1. In the mechanism shown O₁B=75 mm, BA=225 mm, BC=75 mm, CD=150 mm, O₂D=112 mm, if 01B runs at 15 rpm anticlockwise, find velocity of A and angular velocity of O₂D. 188 mm D 150 mm 0₂ lo, 運 Bki 36⁰1

1. In the mechanism shown O₁B=75 mm, BA=225 mm, BC=75 mm, CD=150 mm, O₂D=112 mm, if 01B runs at 15 rpm anticlockwise, find velocity of A and angular velocity of O₂D. 188 mm D 150 mm 0₂ lo, 運 Bki 36⁰1

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: 1. 1.5-Steam is the working fluid in an ideal Rankine cycle. Saturated vapor enters the turbine at 8…

A: GivenP1=8MPa saturated vapourP2=0.008 MPa=8kPaPnet=100 MW

Q: ure 2 ft 1 ft Part A Determine the angular velocity of the spool. The cable wraps around the inner…

Q: Q4. Consider a 5-m-long vertical plate at 60°C in water at 25°C. Determine the forced motion…

A: To find: The forced motion velocity. Given: The length of the plate is L=5 m. The temperature of the…

Q: The shovel load has a mass of 1.4 Mg and center of gravity at G. All joints are pin connected.…

A: Given: The shovel load has a mass of 1.4 Mg and a center of gravity at G. All joints are pin…

Q: The 80.0-lb boy at A is suspended from the cable that passes over the quarter circular cliff rock as…

A: Given Data: at A weight WA= 80 lb at B (woman) weight WB=195 lb co-efficient of static friction…

Q: 4.What factor/s affect the Coefficient of Restitution (CR)? 5. Give at least three instances where…

A: “Since you have posted multiple questions, we will provide the solution only to the first question…

Q: 5.102 For the machine element shown, locate the x coordinate of the center of gravity.

Q: For the system shown in Figure 1, m₁ = 35 kg, m₂ = 20 kg, k₁=1500 and k₂=2000 If the initial…

A: The values are m1=35 kg, m2=20 kg, k1=1500 N/m, k2=2000 N/m. The initial conditions of mass m1 is…

Q: A DC driven double-suction, single stage, centrifugal pump running at 1800 rpm delivers 3.5 gallons…

A: GivenN=1800 rpmQ=3.5 gl/ hrS.G=1.03h=2mhs=3mhd=3mhfs=0.80mhfd=3mη=70%

Q: Water flows into a tank and out through another pipe, as shown in the figure below. The water in the…

A: Given:Surface area, Asurf=5.6 m2Inclination angle of door, θ=25oLength of the door, L=1.1 mWidth of…

Q: 50 kips 6 ft B 560 kip-ft 10 ft 6 ft D 20 kips/ft 12 ft EO 6 ft F

A: The magnitude of vertical reaction at any support is equal to the height of the shear force diagram…

Q: 2. The overhang beam is subjected to the uniform distributed load having an intensity of w = 50 kN/m…

Q: The air conditions at the intake of an air compressor are 33 C, 50 percent relative humidity, and…

A: The intake temperature of the air is T=33°C. The relative humidity of the intake air is ϕ=0.5. The…

Q: A 3-m-high large tank is initially filled with water. The tank water surface is open to the…

A: Given:Initial height of the tank, H=3 mOrifice diameter, d=10 cm=0.1 mLength of the horizontal pipe,…

Q: Please select all standard lengths for 3V belts between 76 in and 115 in.. a. 110 b. 90 in.…

A: The effective outside lengths are 76 and 115 in.

Q: 12.5 Air initially at 50 psia and 660°R expands to atmospheric pressure. The process by which this…

A: Given Data: p1=50 psiaT=660oRpV1.3=Cp2=14.7 psia To Find: (a) Final temperature. (b) Change in…

Q: A tensile force of 10 kN is applied on a 0.02-m diameter and 2-m long rod. After applying the load,…

Q: Problem 1 Determine reactions RA, and RB. A distance between Point A and B is 19ft. Point A is a…

Q: An opaque, horizontal plate has a thickness of L = 21 mm and thermal conductivity k = 25 W/m-K.…

Q: earning Goal: o apply the condition of equilibrium to three-dimensional ystems and solve for unknown…

A: To Find : a) The magnitude of tension in cable AC. Given : The weight is w=810 N The lenghts are…

Q: A 21-mm-diameter steel [E = 206 GPa; a = 12.5x10-6/°C] bolt is used to connect two rigid parts of an…

A: Given-Information:- d =21 mmE = 206 GPaα = 12.5 ×10-6/°Ca = 120 mmT1 = 23°CT2 = 54°CP = 2.4 kN…

Q: Determine the magnitude of the pin force at A. Assume W-850 lb. a 3.0 ft. b-2.2 ft, r = 7 in.

A: Given data:- W= 850 Ib a =3.0ft b =2.2 ft r =7in To find:-the magnitude of the pin force at A

Q: 7-104 An air conditioner with refrigerant-134a as the working fluid is used to keep a room at 23°C…

Q: A.) Air is compressed from 200kPa and 7.00 degrees C to 700kPa and 67.0 degrees C. determine the…

A: This question is based on the concept of entropy.

Q: A hollow steel [G = 12,000 ksi] shaft with an outside diameter of 3.50 in. will be subjected to a…

Q: The brake is to be designed to be self locking, that is, it will not rotate when no load P is…

A: Given data is

Q: 37. A 1-inch solid shaft is to be replaced with a hollow shaft of equal torsional strength having an…

A: Diameter of solid shaft = 1 in Outside diameter of Hollow shaft = 2 in Find the inside diameter of…

Q: A 3-in.-radius drum is rigidly attached to a 5-in.-radius drum as shown. One of the drums rolls…

A: for small drum radius of drum(r1)=3infor large drum radius of drum(r2)=5invelocity at point…

Q: 15-102. The 800-lb roller-coaster car starts from rest on the track having the shape of a…

Q: The task is to parachute supply of 120 kg that includes the containing circular cylinder case of…

A: Given : The diameter of the hemisphere , D=0.4 m

Q: The total head of fan is 200 m and has a static pressure of 210 mm of water gage. What is the…

A: What is the velocity of air flowing if density is 1.16 m3/s.

Q: A hollow steel shaft with an outside diameter of 75 mm and a wall thickness of 5 mm is subjected to…

A: Given data:- do=75 mmt=5 mmT=2410 N⋅mG=80 GPaL=2 m It is required to determine the angle of twist…

Q: 2. The tubular steel shaft is 2 m long and has a diameter of 60 mm. When in operation, it transmits…

A: Given data: L=2 mD=60 mmP=25 kWω=40 rad/sτmax=80 MPaG=75 GPa

Q: Draw the Free Body Diagram (FBD) for the given situation and determine the tension in the cables AB…

A: “Since you have posted a multiple question, we will provide the solution only to the first question…

Q: Determine the force in members EF, CF, and BC of the truss. State if the members are in tension or…

A: Take , P=270 lb To find: The force in members EF, CF, and BC of the truss. State if the members are…

Q: The space truss supports a force F = (-550 i +650j + 400 k} lb. (Figure 1) Figure 6 ft 6 ft 8 ft 6…

Q: Water flows into a tank and out through another pipe, as shown in the figure below. The water in the…

A: Given:Surface area, Asurf=5.6 m2Inclination angle of door, θ=45oLength of the door, L=0.9 mWidth of…

Q: Draw the shear and moment diagrams of each of the following loaded beams and report the maximum…

Q: Calculate the electricity energy required in units of D for desalinating 150 w of water and it takes…

A: The amount of waterV=150 l=0.15 m3 The electricity for per unit of water 3.70 kWhm3

Q: Two 55-kg crates are located on a horizontal ground. Force Pis applied to the crate P as shown in…

Q: I just need help simplifying these equations (1 and 2). Qo,Kic, and CL are all their own variables…

A: Given: q0t1/24CL3q30μt8CL2E'1/4Hq0HT q0t1/24CLq20Kict16CL2E'41/4Hq0HT To find: Simplify both…

Q: For the instant represented, link CB is rotating counterclockwise at a constant rate N = 4.4 rad/s…

A: The angular velocity of link CB is ωcb=4.4 rad/s (counterclockwise)

Q: Spacecraft must be cooled via radiative mechanisms, and one means of doing this is by using…

A: To Find : The temperature profile with in rod. Given : The perimeter is Pd The base temperature is…

Q: Consider the tripod in (Figure 1). Figure 15m 2m 2m 2.5m < 1 of 1

A: Solution: The coordinate of the points are : A=(0,2,0)B=(3.5,2.5,0)D=(2.5,2,4) The direction cosine…

Q: Determine the linear acceleration of A (in m/s²) for = 90° if angular velocity of OB, WOB = 0 and…

Q: the metacenter is above the center of gravity, the buoyant force and the weight will create a: B.…

A: “Since you have posted multiple questions, we will provide the solutiononly to the first five…

Q: A rod-shaped single crystal of pure iron is to be tested in tension. The tensile axis is: [uvw] =…

A: Write the given data. Tensile axis: u v w=1 2¯ 0Slip plane: h1 k1 l1=1 1 0Slip direction: <u1 v1…

Q: Water is stored in a pressurised container at a height HT = 8 m. It then moves through a horizontal…

Q: The A-36 steel pipe in (Figure 1) has a 6061-T6 aluminum core. It is subjected to a tensile force of…

Q: Using the top view, right-side view, and front view. Draw the isometric view.

A: Given: Draw the isometric view.

Concept explainers

Conservation of Energy

In physics, the rule of the conservation of energy states that energy doesn’t disappear from the atmosphere; instead, it changes its form from one type to another. Energy is one of the most important physical quantities in nature, and it cannot be created or destroyed — only transformed.

Question

1. In the mechanism shown O₁B=75 mm, BA=225 mm, BC=75 mm, CD=150
mm, O₂D=112 mm, if 01B runs at 15 rpm anticlockwise, find velocity of A and
angular velocity of O₂D.
188 mm
D
150
mm
0₂
lo,
運
Bki
36⁰1

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data:

VIEW

Step 2: Draw velocity diagram from given mechanism

VIEW

Step 3: Procedure of velocity diagram

VIEW

Step 4: Congratulations of velocity of A and angular velocity of O2D.

VIEW

Solution

VIEW

Step by step

Solved in 5 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The 16 in. diameter pulley of a gasoline engine is connected by a pulley (which is assumed not to slip) to the pulley of apump. The belt speed is 4,000 fpm. Determine (1) the angular speed of the engine pulley in revolutions per minute and inradians per second; and (2) the diameter in inches of the pump pulley if the pump speed is one-half the speed of theengine pulley.
A load is raised 11 ft by the gears and wheel system below. Gear A is initially rotating at rest and accelerates uniformly to omega = 24 rpm in t= 10 sec and maintain then maintain this constant 24 rpm speed. The dimensions are rA= 1 in, rB= 9 in and rC=16 in. 2) After 10 sec, find the distance s2 in feet and in NC es needed to reach the 11 ft, find thetaC2(t), alphaA2, alphaB2 in rad/s^2, omegaA2(t), omegaB2(t) in rad/s, thetaA2(t), in rad and the distance s2 in ft that should be made to get to the 11 ft raising distance of the load. 3) Deduce the number of revolutions made by gear A and how long it will take, to raise the load up to 11 ft.
The power of an engine running at 125 rpm is turned off and the engine comes to rest at the end of 2 min and 40 sec. Assuming that there is no slipping between the belt and pulley surface and that the deceleration is uniform, find 1) the average speed in radians per second of the engine pulley in coming to rest; 2) the total angular distance traveled in revolutions, radians and degrees in coming to rest; 3) the distance in feet traveled by a belt running on the pulley in coming to rest, if the pulley diameter is 3ft.
In a mechanism that is a combination of a four-bar mechanism and a slider-crank mechanism. Slider A moves at a speed of 10 cm/s (constant) to the right. Determine: a. Angular speed of links 3, 4, 5 and link 6. b. Angular acceleration of links 3, 4, 5 and link 6. A.= 10Gm/s
Find the velocity of the slider D and the angular velocity of link CD for the engine mechanism shown in Fig. The crank 01A rotates at a uniform speed of 20 rad/sec in the clock wise direction. The various lengths of the given mechanism are. O1A =0.5 m, AB =1.0m, 02B =0.75m, BC =lm and CD =1.75m.
For items 4-5, consider the slider-crank mechanism shown. Crank AB is 0.500 m long. Rod BD is 1.500 m long. The velocity at point B is 0.500 m/s, ↖45.0°. Which of the following gives the closest value to the speed of the piston at D? Which of the following gives the closest values of the lengths of the sides of the triangle formed by points B and D and point C, the instantaneous center of rod BD?
A load is raised 11 ft by the gears and wheel system below. Gear A is initially rotating at rest and accelerates uniformly to omega = 24 rpm in t= 10 sec and maintain then maintain this constant 24 rpm speed. The dimensions are rA= 1 in, rB= 9 in and rC=16 in. 1) From 0 to 10 sec, find alphaA1, alphaC1 in rad/s^2, omegaA1(t), omegaC1(t) in rad/s, thetaA1(t), thetaB1(t) and thetaC1(t) in rad, and the distance made by the load s1 in inches and in feet made by the load during this time. 2) After 10 sec, find the distance s2 in feet and in NC es needed to reach the 11 ft, find thetaC2(t), alphaA2, alphaB2 in rad/s^2, omegaA2(t), omegaB2(t) in rad/s, thetaA2(t), in rad and the distance s2 in ft that should be made to get to the 11 ft raising distance of the load. 3) Deduce the number of revolutions made by gear A and how long it will take, to raise the load up to 11 ft. In the box below, give the time it takes to raise the load in seconds, with one decimal.
A load is raised 11 ft by the gears and wheel system below. Gear A is initially rotating at rest and accelerates uniformly to omega = 24 rpm in t= 10 sec and maintain then maintain this constant 24 rpm speed. The dimensions are rA= 1 in, rB= 9 in and rC=16 in. 1) From 0 to 10 sec, find alphaA1, alphaC1 in rad/s^2, omegaA1(t), omegaC1(t) in rad/s, thetaA1(t), thetaB1(t) and thetaC1(t) in rad, and the distance made by the load s1 in inches and in feet made by the load during this time.
A pulley has a tangential velocity of 75 fpm. If pulley diameter is 10 inches, find the speed of the speed. A. 24.34 rpm B. 28.65 rpm C. 34.22 rpm D. 32.34 rpm Please solve the Problem elaborately. Your solution will be use as reference for my studies. Thank you so much your work will be appreciated much!
ABCD is a four-bar chain with link AD fixed. The lengths of the links are AB = 70mm; BC = 175 mm; CD = 100 mm; and AD = 200 mm to be horizontal (fixed link).The crank AB rotates at 20 rad/s clockwise. Draw the velocity and accelerationdiagram when angle DAB = 45° and B and C lie on the same side of AD. Find theangular velocity and angular acceleration of links BC and CD.
1. A surge is moving at 9 f t/s into a basin of depth 1.4 f t where the speed is zero. Find the water depth behind the surge and the drift velocity behind the surge (that is, the velocity downstream of the surge in a stationary frame of reference). 2. A river of depth 2 m flows downstream at 1 m/s. A surge of depth H moves up the river at 5 m/s relative to a stationary observer on the bank of the river. Find H.
Link BC (of length 0.47 m) is pin connected at the fixed point C and makes an angleof ⍬ = 51° with the vertical. This link is connected to the vertical link AB (of length0.3 m) and point A is also the axle of a wheel of negligible size that is moving alonga circular track of radius r =2.3 m. If the speed of A is constant and VA = (-2.59)im/s, which one of the following statements is correct? (In the followingstatements, wAB and wBC denote ⍵AB and ⍵BC respectively, where both are definedpositive in the k-direction and given in rad/s, and A denotes the magnitude of pointA's acceleration in m/s2) 1) wAB=0; wBC=0; aA=02) wAB=6,99; wBC=-7.09; aA=03) wAB=8.63; wBC=0; aA=04) wAB=8.63; wBC=0; aA >0 5) wAB=6.99; wBC=-7.09, aA>0