1. In which of the following cases, the Electrostatic Discharge (ESD) is more? Explain how the ESD event taken place in both the cases. a. A person walking across a synthetic carpet on a dry day and generates a potential of 15 kV on his body.

1. In which of the following cases, the Electrostatic Discharge (ESD) is more? Explain how the ESD event taken place in both the cases. a. A person walking across a synthetic carpet on a dry day and generates a potential of 15 kV on his body.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

What do you understand by Ferranti effect? Subject Power Transmission and Distribution
Please answer the following points in detail and rigorously. Instead ofresort to formulas, develop from basic principles (laws ofvoltages and currents, definition of electrical power, properties ofphasors, among others) a) Suppose that between the two terminals of an element there is a voltage v (t) and that through the terminal marked with a positive sign a current i (t). Show that if v (t) and i (t) are sinusoidal and are out of phase an angle θ, then the active power P which is consumed by this element is proportional to cosθ. b) How much is P for a pure inductor and how much for a capacitor pure? Does this make physical sense? c) When the power factor seen between two terminals is specified, Why is it necessary to indicate whether it is late or early? d) Show that the complex power consumed by two elements in parallel is the sum of the individual complex powers. After, repeat the procedure but for two elements in series. e) What meaning would you give to the P consumed by an…
Answer the following points in detail and rigorously. Instead of resorting to formulas, develop from basic principles (laws of voltages and currents, definition of electrical power, properties of phasors, among others). d) Show that the complex power consumed by two elements in parallel is the sum of the individual complex powers. Then repeat the procedure but for two elements in series. e) What meaning would you give to the P consumed by an element? Which to Q?
A lossy capacitor Cx, rated for operation of 5 kV, 50 Hz is represented by an equivalent circuit with an ideal capacitor Cp in parallel with a resistor Rp. Cp is 0.102 microF and Rp=1.25 Mohm. The power loss, and loss tangent of this lossy capacitor at rated voltage respectively ?
A solid specimen of dielectric dielectric constant of 4.0, shown in the figure has an internal void of thickness 1mm. The specimen is 1cm thick and is subjected to a voltage of 80 kV(rms). If the void is filled with air and if the breakdown strength of air can be taken as 30 kV(peak)/cm, find the voltage at which an internal discharge
a)We have a two-wire overhead transmission line, powered by a constant voltage source of 700 V. The values for the inductance of the conductors are 2.348x10-3 H/km and the capacitance values are 6.325x10-9 F/km. Assuming an ideal (no loss) line and its length at 130 km, determine the natural impedance of the line. b) What is the transient phenomenon in a transmission line? As an example of its causes.
Estimate the AEP for a 3-MW wind turbine in a wind regime that has a CF= 30%. For this turbine explain why the increase of wind speed to levels greater than 25 m/s generates less electrical power compared to wind speeds around 11 m/s
what is the mutual inductance in ohms (or the mutual inductive reactance ) between the two mutually-coupled inductors? if circuit to the left of load Z is converted into its Thevenin's equivalent, what would be the magnitude of ZTh in ohms? what is the phase angle of ZTh in degrees? what would be the phase angle of VTh in degrees? what would be the magnitude of VTh in volts if E = 120 V?
A telephone receiver has an impedance of 306 ohms at 800 cps and a resistance of 60 ohms. For what value of capacitance of a capacitor in series with the coil will the power factor be unity at 1,000 cps?
Answer the following points in detail and rigorously. Instead of resorting to formulas, develop from basic principles (laws of voltages and currents, definition of electrical power, properties of phasors, among others). a) Suppose that between the two terminals of an element there is a voltage v (t) and that a current i (t) enters through the terminal marked with a positive sign. Show that if v (t) and i (t) are sinusoidal and are out of phase by an angle ϕ, then the active power P that is consumed by said element is proportional to cos ϕ. b) How much is P for a pure inductor and how much for a pure capacitor? Does this make physical sense? c) When specifying the power factor seen between two terminals, why is it necessary to indicate whether it is lagging or leading? d) Show that the complex power consumed by two elements in parallel is the sum of the individual complex powers. Then repeat the procedure but for two elements in series. e) What meaning would you give to the P consumed…
Answer the following points in detail and rigorously. Instead of resorting to formulas, develop from basic principles (laws of voltages and currents, definition of electrical power, properties of phasors, among others). a) Suppose that between the two terminals of an element there is a voltage v (t) and that a current i (t) enters through the terminal marked with a positive sign. Show that if v (t) and i (t) are sinusoidal and are out of phase by an angle ϕ, then the active power P that is consumed by said element is proportional to cos ϕ b) How much is P for a pure inductor and how much for a pure capacitor? Does this make physical sense? c) When specifying the power factor seen between two terminals, why is it necessary to indicate whether it is lagging or leading?
a question by considering the annual load time curve for an electric station as a straight line from 20mw to 3mw, and to cover these loads, then operate three generating units, the first and second, each with a capacity of 10mw, while the third has a capacity of 5mw, and illustrate the load time curve by drawing, then find: 1- the total capacity of the station 2- the maximum demand 3- capacitance coefficient 4- pregnancy coefficient 5 utilizatio