also like to keep one window air conditioner running, as well as run the refrigerator in your kitchen. When days. The freezer in the basement contains $300 worth company will not be able to fix the problem for several of food that you cannot afford to let spoil. You would as well as run the refrigerator in your kitchen. When these appliances are on, they draw the following currents (all values are rms): Air conditioner: 9.6 A rms @ 120 V rms pf = 0.90 lagging %3D Freezer: 4.2 A rms @ 120 V rms pf = 0.87 lagging %3D Refrigerator: 3.5 A rms @ 120 V rms pf = 0.80 lagging %3D In the worst-case scenario, how much power must an emergency generator supply?

also like to keep one window air conditioner running, as well as run the refrigerator in your kitchen. When days. The freezer in the basement contains $300 worth company will not be able to fix the problem for several of food that you cannot afford to let spoil. You would as well as run the refrigerator in your kitchen. When these appliances are on, they draw the following currents (all values are rms): Air conditioner: 9.6 A rms @ 120 V rms pf = 0.90 lagging %3D Freezer: 4.2 A rms @ 120 V rms pf = 0.87 lagging %3D Refrigerator: 3.5 A rms @ 120 V rms pf = 0.80 lagging %3D In the worst-case scenario, how much power must an emergency generator supply?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.1MCQ: The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmax

See similar textbooks

Similar questions

A residential four-wire system supplies power at220 V rms to the following single-phase appliances:On the first phase, there are ten 75-W bulbs. On thesecond phase, there is a 750-W vacuum cleaner with apower factor of 0.87. On the third phase, there are ten40-W fluorescent lamps with power factor of 0.64.Finda. The current in the netural wire.b. The real, reactive, and apparent power for eachphase.
A voltage waveform is shown below, please find its RMS voltage value. Choose the value that is closest to the answer. NEED A NEAT HAND WRITING ONLY OTHERWISE WILL LEAVE A DOWNVOTE NO CHAT GPT MINIMUM3 STEPS WITH EXPLANATION
Determine the rms values of each of the following (a) v(t) = 100 sin(ωt) V Vrms = 70.7V (b) i(t) = 8 sin(377t) A Irms = 5.656V(c) v(t) = 40 sin(ωt + 40o) V Vrms = 28.28V (d) i(t) = 120 cos(ωt) mA Irms = 84.84A Can you double check if my answer is correct?
Two sinusoidal voltages of the same frequency have rms values of 8 V and 3 V. What is the smallest rms value that the sum of these voltages could have? The largest? Justify your answers.
A voltage given by v(t) = 311 cos (311 pi t) V is applied to a 50-ohm resistance. (a.) Sketch v(t) to scale versus time. (b.) Determine the rms value of the voltage and the average power delivered to the resistance. (c.)Determine the power as a function of time and sketch to scale.
A 1000-W electric motor is connected to a 120 V rms, 60-Hz source. The power factor seen by the source is 0.8, lagging. To correct the pf to 0.95 lagging, a capacitor is placed in parallel with the motor. Calculate the current drawn from the source with and without the capacitor connected. Determine the value of the capacitor required to make the correction.
A voltage is given by v( t )=10 sin(1000πt+30°). First, use a cosine function to express v(t). Then, find the angular frequency, the frequency in hertz, the phase angle, the period, and the rms value. Find the power that this voltage delivers to a 50-Ω resistance. Find the first value of time after t=0 that v(t) reaches its peak value. Sketch v(t) to scale versus time. * Denotes that answers are contained in the Student Solutions files. See See Appendix E for more information about accessing the Student Solutions.
A 250 V rms system is supplying three parallel loads. One draw 20kW at unity pf, a second uses 25 kVA at 0.8 lagging pf, and the third requires a power of 30 kW at a lagging pf of 0.75. At what power factor does the source operate?
Q6: An AC source operating at 60 Hz with a maximum voltage of 170 V is fed to a series combination of1.2kΩ resistor and 2.5μF capacitor connected in a timer circuit. How can you evaluate the maximumcurrent in the circuit? Can you estimate the rms value potential difference across each circuit element?Compare the power factor of this timer circuit with a circuit contain only ohmic resistance. Justify youranswer?
Determine the rms (or effective) value ofv(t) = VDC + vAC = 50 + 70.7 cos(377t) V
A 50 Hz, alternating voltage of 150 V (rms) is applied independently to: (a) resistance of 10 ohms,(b) inductance of 0.2 henry’ and(c) capacitance of 50 microfarad. Find the expression of the instantaneous current in each case. Draw the phasordiagram in each case.
An example power system has two distinct manufacturing areas, one with harmonic loads, and another with only linear loads. The portion of the system with the harmonic loads draws 75 A rms at 60 Hz, 10 A rms at 300 Hz, and 5 A rms at 420 Hz. The part of the system with only linear loads draws 75 A rms at 60 Hz. (i) What is the total load current (at 60 Hz) if both manufacturing plants are running? Calculate the THD. (ii) What is the total load current (at 60 Hz) if only the manufacturing plant with harmonic loads is running? Calculate the THD.