1. On a lossless 500 coaxial transmission line with a shorted load: a. a voltage minimum will occur at the load. b. a current maximum will occur at the load. c. a voltage maximum will occur X/4 back from the load. d. the voltage and current are in phase. e. the voltage and current are 90° out of phase. f. the standing wave moves toward the source.

1. On a lossless 500 coaxial transmission line with a shorted load: a. a voltage minimum will occur at the load. b. a current maximum will occur at the load. c. a voltage maximum will occur X/4 back from the load. d. the voltage and current are in phase. e. the voltage and current are 90° out of phase. f. the standing wave moves toward the source.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter5: Transmission Lines: Steady-state Operation

Section: Chapter Questions

Problem 5.18P

See similar textbooks

Similar questions

A 300ᘯ transmission line is 0.8 m long and terminated with ashort circuit. The line is operating in air with a wavelength of 0.8m and is lossless. (a) If input voltage is 10V, what is themaximum voltage amplitude at any point on the line? (b) Whatis the current amplitude in the short circuit?
The capacitance per unit length and the characteristic impedance of a lossless Transmission line are C and Z0 respectively. Express the velocity of travelling wave on the transmission line in terms of the two given parameters above.
Express the velocity of wave on a lossless line in terms of c and z0 with proper derivative. C is capacitance of transmission line
An 8000 V, 60 Hz, single-phase, transmission line consists of two hard-drawn aluminumconductors with a radius of 2 cm spaced 1.2 m apart. If the transmission line is 30 km longand the temperature of the conductors is 200C,a. What is the series resistance per kilometer of this line?b. What is the series inductance per kilometer of this line?c. What is the shunt capacitance per kilometer of this line?
A lossless transmission with characteristic impedance of ?0 = 100Ω and length = 52cmThe line was terminated with a load of ?? = 30 + ?50Ω. According to what is given, a) The reflection coefficient in the load and the voltage standing wave ratio on the line (GDDO)Find out.b) Find the impedance and admittance at the line input. (for ? = 750???)c) For ? = 750???, the impedance and admittance values 2cm away from the load.(It will be assumed that = ?0.)
Derive an expression for sag in a transmission line of equal height poles
A 50Ω lossless transmission line is terminated with a load impedance valued ZL = RL + jXL.According to what is given, a) RL for Voltage Standing Wave Ratio to be 2What should be the relationship between XL and?b) If RL = 100Ω, find the value of XL.c) Find the voltage minimum point closest to the load on the line.
1. What is the necessary condition for matching transmission lines? In addition, what is a micro strip line? 2. For a distortion less line α = 0.02dB/m, Z0 (R0) = 60Ω and C = 0.2nF/m. Find the resistance and velocity of wave propagation. [Do not forget the units.] 3. For a finite lossless transmission line with open-circuit termination, sketch Xio vs l. Indicate where the sketch is inductive and capacitive.
a) Discuss the effect of primary constants of a transmission lines onsignal propagation b) Using mathematical theories discuss how the standing wave phenomenon comes about and what can be done to eliminate it completely. c) Develop an expression for voltage and current traveling on atransmission line assuming all its primary constants are uniformlydistributed.
A lossless transmission line has 100 ? characteristic impedance. The line is terminated in a load impedance of 70-j100 ?. The maximum voltage measured on the line is 200V. Find;1. The minimum current and minimum voltage on the line2. Explain how location of voltage maximum can be determined by using load reflection coefficient from the forward and backward wave.3. Using load reflection coefficient in ii., calculate the distance from the load that produce the maximum voltage and current.
What is meant by transmission line and Attenuation in transmission lines and why it is happen? justify your answer with suitable examples and figures?
In a three-phase transmission line with a length of 150 km, a voltage of 250 kV and a frequency of 50 Hz, the diameter of the steel-cored aluminum conductors is 18 mm, the roughness coefficient of the conductors is 0.6, and the spacing between the conductors is 6 m. Since the average air temperature is 27˚ C and the air pressure is 762 mmHg along the line, find the corona voltage around the conductor and the total loss of the line according to the Peek formula.