1. Portal Method The frame shown is subjected to lateral loads as shown. Supports S, T, U V, W and X are rigid supports. Determine the following: a) The shear forces in columns and girders.

Q: Note: per grid is equal to 1 meter, all loads are in Newtons. All members are 900 mm?. Required: 1)…

A: Since we only answer up to 3 subparts, we'll answer the first three. Please resubmit the question…

Q: (b) A cantilever truss has support reaction at A and B was hanging one pot flower of 25kg as shown…

A: Given that, * Ac, BC, BD = ?Cut the section such that all 3 forces are included,shown in figure.…

Q: The beam is constructed from four boards as shown. If it is subjected to a moment Mz = 16 kips-ft,…

A: Given Mz= 16 kips-ft Determine the stress at points A and B.

Q: The uniform concrete slab has a mass of 2400 kg. Determine the tension in each of the three parallel…

A:

Q: Determine all the forces acting on the structure shown. Also, indicate the type of force  acting on…

A: To Determine all the forces acting on the given structure and state the nature of their forces.

Q: Refer to the truss shown  a. Determine the maximum positive ordinate for  member DC.  b. Determine…

A: First we will draw the Influence lines for member AB and DC

Q: 15kN 15kN 10 kN 15kN 1.5 m 2.25 m H 1.5 m 2.25 m 1.5 m 1.8 m 18 m 2.4 m. 2.4 m 2.4 m.

A: Given data in question  Point loads Span member length  To find out  Member forces in AJ and AB…

Q: For the truss shown in Figure 2.3b, determine the force in member AM if x = 7 m, y = 3 m, and P = 13…

A:

Q: The frame shown is subjected to lateral loads as shown. Supports S, T, U, V, W, Z are rigid…

A: In portal method, 1. Hinges are assumed at middle of each member. 2. frame is cut at different…

Q: Problem 1 Determine the forces for each bar member and state if the members are in tension or…

A: Let, AV & DV be the vertical support reactions at A and…

Q: Calculate the forces in each member. P₁ D H A a B P₂ b C у

A: Let's calculate the different angles , required for the calculation tanɵ = CC'/AC' = (3-1)/(2+1) =…

Q: Consider the given figure.A floor truss is loaded as shown. Determine the force in members CF, EF,…

A:

Q: Determine the forces FG, DH & EH of the truss using method of joints. 10 k 20 k 30 k 7B 30 k+ 10 k…

A:

Q: Compute the bending moments at the top of the columns in the upper storey of the mutli-storey frame…

A:

Q: Two rods and one cable are attached to the support at O. Two of the forces are as shown and the…

A: step 2

Q: Determine the force in members BC, CD, and CG, if W = 8 kN. Specify whether each member is in…

A: At Joint E : ∑Fy = 0FEG + 8 = 0 ⇒ FEG = - 8 kN (Compressive)∑Fx = 0FED + FEGcos30o = 0FED +…

Q: Solve the problem with complete and neat solution. Draw the figure. Determine the force in each…

A:

Q: Determine all the forces acting on the structure shown. Also, indicate the type of force  acting on…

A: Tension is generally a force that stretches something. Compression is generally a force that…

Q: Given the Truss as shown below with load P,=XN and P, = 3X N. Using Method of Joints, determine the…

A:

Q: Determine the load in each member of the truss in figure below

A: Truss is a structure that is the combination of three or more members which acts as a single object.…

Q: As shown, the truss is loaded by the forces P₁ = 830 N and P₂ = 1870 N and has the dimension a =…

A:

Q: Part B As shown, the truss is loaded by the forces P₁ = 830 N and P₂ = 1870 N and has the dimension…

A:

Q: 8 kN C 2m 1 (3) 15 kN - 2m- -2m-

A:

Q: Determine the force in EA member of the truss, and state if the members are in tension or…

A:

Q: 1. Portal Method The frame shown is subjected to lateral loads as shown. Supports S, T, U V, W and X…

A: The assumption in the portland method:- For each storey of the frame, the interior column will take…

Q: 4. Draw the moment diagram for girder IJKL of the building frame. Use the portal method of analysis.…

A:

Q: 4. Consider the angle iron. If the moment acting on the cross section is 936 kip-ft, determine the…

A: Answer To calculate the Maximum compressive stress and Maximum tensile stress we can use the Bending…

Q: Part B As shown, the truss is loaded by the forces P = 195 lb and P = 400 lb and has the dimension a…

A: Method of joints : The method of joints is a method for calculating unknown forces operating on…

Q: The frame below is subject to applied loads of X = 2 kN and Y = 4 kN. Assuming the frame dimensions…

A: Consider the FBd of the joint 5 as shown:

Q: (b) Figure Q2(b) shows that the truss supports loads at point C and E. If the value of F = 3 kN,…

A: In this question, we shall first use method of sections to determine force in the member BE and then…

Q: 1- Compute the force in each member of the loaded cantilever truss by the method of joints. B 5 m 5…

A:

Q: Determine the magnitude of the tension at support A (N). Supports are pin connected

A:

Q: A rigid beam is loaded with negligible mass and pinned at B and supported by two identical rods,…

A:

Q: B. Refer to the structure below: 1. Isthe structure a truss or frame? Explain. 2. Which among the…

A: Given; The force acting on the member, P = 600 kN

Q: The given truss structure is loaded by a force F at the joint D and is to examine their buckling…

A: Solution- The given diagram is shown below,

Q: Determine the load P such that all the members in the three-hinged arch in the figure are in pure…

A: The given figure is shown below:

Q: The truss shown is designed to support a staircase. For all questions, indicate whether the members…

A: To find a. Determine the force in members EG, FG, and HFb. Determine the force in members EF and DF

Q: The center panel of the truss contains two flexible cables. What load P will cause a compressive…

A:

Q: For the figure shown, determine the horizontal and vertical components, respectively, of the hinge…

A: From the given question it is required to determine the horizontal and vertical components of the…

Q: 2. Given the truss below, calculate the forces in each member in kN. Indicate also if the member is…

A: Consider the free body diagram of the beam shown below. Here, M=400 kN and N = 300 kN

Q: Determine the largest load P that can be applied to the frame

A:

Q: Determine the maximum flexural stress of the beam shown.

A: To calculate the maximum flexural stress in the given beam.   Given, Width of beam, b = 75 mm Depth…

Q: 1 m F A 1m B. E 45° 2 kN 45° D 5 kN

A: The problem can be solved by using both method of sections as well as method of joints. First…

Q: 4. Determine the forces For, For & Fre of the truss using method of sections. 20 20 20 50 kN 80 kN…

A:

Q: G H -67.5 kN 3.6 m -112.5 kN E F 3.6 m 6 m -4.5 m- Use portal method to analyze the frame. Determine…

A:

Q: 1- A vertical tower truss shown below is supporting a water tank and is also subjected to horizontal…

A:

Q: Example The man has a weight W and stands at the center of the plank. If the planes at A and B are…

A: Draw the free body diagram of the man stands at the center of the plank Consider the applied force…

Q: 3.30 For the truss and loading shown, determine the resultant of the loads and the distance from…

A: To find resultant and it's location from A

Q: With the truss below, solve the force experienced by each members and indicate if it is a…

A: Note: We subject expert are allowed to only one question . so I am doing only first question.…

Q: 2. Compute the force in each member of the loaded cantilever truss by method of joints. B 5 m 5 m 5…

A:

Length and Length related Variables

Length can de defined as the measurement or extent of physical quantities or objects from one terminal to another terminal. Stone age humans used finger length, step length, and so on to measure the size or displacement of an object. Nowadays, depending on how precise the measurement requires to be and the object’s size is measured, we use measuring devices for measurements like rulers and steel tape. Most people have used a ruler or tape measure to measure a particular distance or the size of an object. For more precise measurements of tiny objects, the development of measurement tools such as the Vernier caliper, which permits us to measure dimensions within 1/1000 of an inch. In the last few decades, electronic distance measuring instruments (EDMI) have been implemented that permit us to measure distances from a few feet to many miles with reasonable accuracy.