CONFIDENTIALBFC21403QI(a)(i)List FOUR (4) process in structural engineering design.(ii)Give the difference between suspension cable bridge and cable-stayed bridgeand explain the advantage of cach type of bridge.A cantilever truss has support reaction at A and B was hanging one pot flower of 25kgas shown in Figure Q1(b). Categorize member AC, BC and BD whether incompression or tension condition.(b)A 02 m C o2 m E 0.1m G0.1 mBFIGURE QI(b)

Given that, * Ac, BC, BD = ?Cut the section such that all 3 forces are included,shown in figure.…

(b) A cantilever truss has support reaction at A and B was hanging one pot flower of 25kg as shown in Figure Q1(b). Categorize member AC, BC and BD whether in compression or tension condition. A 02m C 02m E 0.1m G 0.1 m B 0.3m

(b) A cantilever truss has support reaction at A and B was hanging one pot flower of 25kg as shown in Figure Q1(b). Categorize member AC, BC and BD whether in compression or tension condition. A 02m C 02m E 0.1m G 0.1 m B 0.3m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

We have been solving problems like these by dividing the whole system into the primary structures and original loads on one diagram and another with the redundants. The steps are 1- Classify structure -- the degree 2- Draw the primary with original loads and the primary with redundants 3- Superposition -- determine deltaB1 and deltaB2 4- Compatibility (where the other picture shows different cases) 5- Finidng the equilibrium forces and such. I have started this problem but I want to confirm my thought process is right, you may ignore part C
The floor system used in a school classroom consists of a 4-in.reinforced stone concrete slab. Set a = 10 ft, b = 30 ftLoading: 4 inches reinforced stone concrete slab = 0.15 k/ft³LL for classrooms = 0.04 k/ft² Using “No.10-11” problem. Set a = 10 ft and b = 15 ft. What is the reaction at B and F?a. 5.50 kb. 4.50 kc. 6.50 kd. 7.50 k What is the magnitude of the triangular loading that acts along girder ABCDE?a. 0.45 k/ftb. 0.55 k/ftc. 0.65 k/ftd. 0.75 k/ft Using “No.10-11” problem. Set a = 7.5 ft and b = 20 ft. What is the loading that acts along joist BF?a. 0.475 k/ftb. 0.575 k/ftc. 0.675 k/ftd. 0.775 k/ft What is the loading that acts alongside girder ABCDE.a. 4.75 kb. 5.75 kc. 6.75 kd. 7.75 k
If rope BC will fail when the tension becomes 50kN, determine the greatest verticle load F that can be applied to the beam at B. What is the magnitude of the reaction at A for this loading? Neglect the thickness of the beam
choose the correct answer Why in an arch bridge is the arch at the bottom of the bridge, but in the suspended bridge it is the highest of the bridge * a-The suspension bridge conveys the load plumbly to the cables and then to the pillars b-Because of the lack of loads on the suspension bridge c-Nothing mentioned
Consider a column bean under compression. A load P is applied at the upper end.Both ends have pinned boundary conditions. As you answer the following questions, you must explain each step, so you can show that you understand each step. You must also be concise and very brief.a.What is the critical load for this system. b.Assume that you now add a pinned supportis located a third of the way from the top of the column,and athird from the bottom of the column. These pinned supports prevent the column from laterally translating at the points of support. What is the new critical load of this system? Solve this problem in two very simple ways
Determine the support reactions. ** need asap pls. Thanks.
The nominal Pn-Mn, interaction diagram is given in Figure P1.4 for a reinforced concrete column with ties in Figure P1.4. If Pn =800 kip, Mn= 200 kip-ft, will the column fail or not? (Hint: use Ø valve to generate the ultimate strength curve per AC1318 code).
The jib crane shown is subjected to three coplanar forces.Replace this loading by an equivalent resultant force and specifywhere the resultant’s line of action intersects the column AB andboom BC.
A 6.5m long cantilever beam 300mm x 600mm carries a uniformly distributed dead load(beam weight included) of 5kN/m throughout the length and a concentrated live load of 19KN at the free end. To prevent excessive deflection of the beam it is pretensioned with 12mm diameter strands causing a final prestress force of 550 KN. Pe= 0.85Pi 2. Determie the resulting stress at the top of the fixed end if the center of gravity of the strands is at 100mm above the neutral axis of the beam A.18.79 MPa B.12.77 MPa C. 6.66 MPa D. 6.61 MPa E. None
Pls solve fast for like An L-shape gate AOB weighing 20 kN at its center of gravity G, 0.6 m above the bottom and 0.5 m from the left , 2 m wide perpendicular to the paper. Determine the height h (in unit of meters) of the water surface coinciding the top of the gate and no reaction develop at the stop. Use unit weight of water = 9.80 kN/m^3.
Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress in each material given that P = 15 kN? Specify whether tension or compression. Bronze Aluminum Steel A=400 mm? A=600 mm? A= 300 mm? 2P 3P 4P P -3 m + 5 m -4m
A beam is supported by a column 3 m tall with dimensions a x 1.5a as shown above. The column is fixed at the base and pinned to the beam. Assume a Young’s modulus of ? = 25 GPa and yield strength of ?? = 20 MPa for the column.a) Draw the SFD and BMD for the beam and determine the axial load acting on the column.b) What is the minimum value of “a” that would not result in buckling of the column?c) If the column was instead fixed to the beam, how would this change the minimum value of “a”?