1. Sketch the specific schematic diagram of functional elements for this measuring instrument. 2. Is the measuring instrument of the Pressure Type Thermometer considered as Null or Deflection type measuring device, why? 3. What is the opposing effect in this measuring instrument which is introduced according to the physical effect and where does it occur? 4. Sketch only the specified configuration of input- output relationship diagram including only two quantities of Interfering inputs with only two quantities of Modifying inputs.

1. Sketch the specific schematic diagram of functional elements for this measuring instrument. 2. Is the measuring instrument of the Pressure Type Thermometer considered as Null or Deflection type measuring device, why? 3. What is the opposing effect in this measuring instrument which is introduced according to the physical effect and where does it occur? 4. Sketch only the specified configuration of input- output relationship diagram including only two quantities of Interfering inputs with only two quantities of Modifying inputs.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Suppose the frequency of a system is measured to be 2rad/s and after the addition of another mass the frequency is measured to be 1rad/s, calculate the mass and stiffness.
A thermometer having a first-order response is used to measure the temperature profile with the triangular wave as shown below. Sketch the response of the output if 10 TS . (No calculation is required)
Please explain me how you got the answer. Consider a pulley system shown below. Let x be the displacement of the pulley's center of mass. Assume there is no slip between the cord and the pulley. What is the potential energy of the system? Select all that apply.
a string is attached to a mechanical vibrator, which has a frequency of 30Hx. the sttring is 3.0m long and has a linear density of .4 g/cm. the tension is varied by adding weights to teh string passing over the pully. What tension is needed to cause the string to resonate with the vibrator in four segments. assume that he points where the string meets the vibrator and the pulley are approx nodes.
A Thomas meter is located in an air duct of 2 sq ft cross-sectional area. The air weighs 0.083 lb per cu ft, and its specific heat is 0.24. Assume a controlled temperature differential of 5° and heater potential of 110 volts. Plot the velocity as abscissa and amperage as ordinate for veloc- ity 0 to 300 ft per min. Assume constant amperage of 3, and plot tem- perature difference against velocity. Discuss the curves from the stand- point of accuracy of the system.
(Q4) A thermopile 18 constructed with Iron-constantan materials. Four junctions are maintained at 300°C and for junctions are maintained at 40°C. The output of the thermopile is connected to a potentiometer. What voltage will be indicated if both terminals of the potentiometer are at the same temperature? What is the temperature indicated in this case?
Model the problem in terms of a differential equation
Measurement & metrology thermometer reads 97.2 C and the static correction given in the correction cu is-0.06 °C. Determine the true value of the temperature.
A converted box board sample measures 1.625 ft (Length) by 1.5 ft (Width) with theflutes running along the 1.5 ft dimension (see below picture). The box uses a C-flute medium,which is characterized by a take-up factor of 1.44.What is the estimated distance for the stretched out medium in feet?
A special instrument that will accommodate type E thermocouples operating over the range of -150 to 100°C is going to be designed. At some stage of design, the sensitivity at 0°C is needed. What is the sensitivity of the thermocouple at 0°C?
kitchen oven has a dial thermometer with a resolution of 10 degrees. The error caused by interpolation due to the use of this dial thermometer is 95% expected to be:
Define the displacement compatibility equation, the virtual loading state and the main system of the structure.