1. State in words the condition for rotational equilibrium. 2. In exercise physiology studies, it is sometimes important to determine the location of a person's center of gravity. This can be done with the arrangement shown in the figure below. A light plank rests on two scales that read Fg1= 380 N and Fg2 = 320 N. The scales are separated by a distance of 2.00 m. How far from the woman's feet is her center of gravity? 2.00 m HO Fgl Fg2 OHP

1. State in words the condition for rotational equilibrium. 2. In exercise physiology studies, it is sometimes important to determine the location of a person's center of gravity. This can be done with the arrangement shown in the figure below. A light plank rests on two scales that read Fg1= 380 N and Fg2 = 320 N. The scales are separated by a distance of 2.00 m. How far from the woman's feet is her center of gravity? 2.00 m HO Fgl Fg2 OHP

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

As shown in the figure below, a cantilever beam has a span of 6m long. And it is subjected to a concentrated load 6kN acting 4m from the support and a clockwise moment of 30kN.m at the free end. E = 200 GPa and I = 100,000,000 ??^4 . (Use area moment method) a) Determine the deflection at the free end due to concentrated load only. b) Determine the maximum deflection at the free end.
1. Determine whether the structure shown is unstable, statically determinate, statically indeterminate to the first degree, or statically indeterminate to the second degree. 2. A truss is loaded as shown in the figure. Assume AE = 10000 kN. Which of the following most nearly gives the relative displacement between joints BD due to the two unit loads acting on joints B and D towards each other? A. 1.93 mm B. 1.02 mm C. 1.20 mm D. 1.39 mm
a 50-m steel tape is of standard length under a pull of 5.5 kg when supported throughout its length. the tape weighs 0.05 kg/m, has a cross-sectional area of 0.04 sq. cm , and being made of steel , its modulus of elasticity is 2.10 x10^6 kg/cm^2. this tape was used in the field to measure a distance that was determined to be 458.650 m. at the time the measurement was made, the constant pull applied was 8 kg with the tape supported only at its endpoints. determine the following:a) Correction measure line due to tensionb) Total correction due to sag c) correct length of measured line corrected for effects of tension and sag
A 50-m steel tape is of standard length under a pull of 5.5 kg when supported throughout its entire length. The tape weighs 0.05 kg/m, has a cross-sectional area of 0.04 sq. cm., and being made of steel, its modulus elasticity is 2.10x10^6 kg/cm2. This tape was used in the field to measure a distance that was determined to be 458.650 m. At the time thr measurement was made, the constant pull applied was 8 kg with the tape supported only at its end points. Determine the correct length of the line.
Q3. Find the vertical deflection of joint (b), if the modulus of elasticity (E = 30*10° kN/cm’), area of each member is (A =4 cm’). 10 kN SkN ! 6m . 6 m 6m |, 6m e ale
A 50-m steel tape is of standard length under a pull of 5.50 kg and a temperature of 20°C when supported throughout its entire length. The tape weighing 0.05 kg/m, has a cross sectional area of 0.04cm2 and a modulus of elasticity of 2x106 kg/cm2. This tape was used in the field to measure a distance that was determined to be 458.65m. At the time the measurement was made, a constant pull of 8kg was applied with the tape supported at endpoints only. During the measurement, it was a cool atmosphere at an average temperature of 18°C. Determine the correct length of the line.
Using ANY GEOMETRIC METHOD Consider 250 mm x 400 (b x h) mm section and E = 100,000 MPa. Enter the absolute value only and round-off your answer to 3 decimal places. GIVEN: a = 5.6 m b = 4.4 m c = 15.9 kn/m d = 22 kn QUESTIONS: 1. Determine the VERTICAL REACTION at B in KN. 2. Determine the SLOPE at B in DEGREES. 3. Determine the DEFLECTION at D in MM. 4. Determine the DEFLECTION AT MIDSPAN OF THE BEAM in MM. Thank you! Please answer all. ❤️
A 50 m steel tape measured 50.0250 m when standardized fully supported under a 90-newton pull at a temperature of 20°C. The tape weighed 12N and had a cross-sectional area of 0.028 cm^2. What is the true length of the recorded distance AB for the following condition? (K= 0.0000116/°C, modulus of Elasticity =2.1x10^7).Recorded distance: 215.095 mAverage temperature: 12°CMeans of support: SuspendedTension: 120 NElevation difference per 100 m: 2.5mRound off the final answers to the nearest hundred thousandths (five decimal places) and indicate if the answer is positive or negative. 1. Determine the temperature correction for the entire length of the distance measured. 2. Give the correction for the absolute length of the tape, accounting the full length it measured. 3. Determine the sag correction for one tape length. 4. Determine the pull correction for the entire length of the distance measured. 5. Compute for the slope correction for the entire length of the distance measured.
5. Given: XW = 48.85 ft and weight of W = 652 lb, ? = 36° Solve for the tension in XW connected to W in lb at Y, wherein velocity of W = 14.8 ft/s Report your answers in 3 significant digits
Need help experts. The rigid body shown in the figure is subjected to the indicated force system. Determine the forces applied at points A and E that equal the applied force system.Data: β = 48°; a = 6,6 m; b = 8,9 m; F = 31 kN; P1 = 20,743 kN; P2 = 23,037 kN The force applied at point A is FA = ? Answer kN and the force applied at point B is FB = ? Answer kN.
Use THREE MOMENT EQUATION MET determine the member end moments of the beam of the rectangular cross section shown in Figure 11.10a. Assume that support B settles 2 cm. The modulus of elasticity and the moment of inertia of the beam are E = 210,000 N/mm2 and 4.8 × 104 mm,4 respectively. Hint final answer: MAB= 0 MBA= 165.5127 kn.m MBC= -165.5127 kn.m MCB= 52.2604 kn.m
Compute the resultant of the three forces shown in the figure. a.) None of the Above b.) 315.28 N c.) 836.90 N d.) 894.32 N e.) 948.27 N