Equal torques are applied to thin-walled tubes of the same length L, same thickness t, and same radius r. One of the tubes has been slit lengthwise as shown, determine; a) the ratio of their maximum shearing stress Tb/Ta b) the ratio of the angle of twist of the shaft 0/0a T (b) (a)

Equal torques are applied to thin-walled tubes of the same length L, same thickness t, and same radius r. One of the tubes has been slit lengthwise as shown, determine; a) the ratio of their maximum shearing stress Tb/Ta b) the ratio of the angle of twist of the shaft 0/0a T (b) (a)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: For a frame shown, a 4442 N load is acting on a member ABD at D. If the allowable material shear…

A: Given Data:Load = 4442Nshear stress = 44Mpadia = 2.5mm thickness of member BC= 12mmDE=16mm

Q: USE FORCE METHOD. What is the force member AC in the given truss? AE is constant. (kN) Vertical…

Q: Longitudinal spacing of bolts in built-up members is reversely proportional to the applied shear…

A: Asked: To determine whether the given statement is true or false corresponding to longitudinal…

Q: For the beam shown, calculate the beam slope at A. Assume that a = 80 in., b = 270 in., c = 109 in.,…

Q: The extruded plastic shape has dimensions of D = 23 mm, d = 21 mm, a = 93 mm, and t = 3 mm. (a)…

Q: For the figure shown, under the same loading and supporting conditions, the deflection of the steel…

A: Given data: The loading and supporting conditions are same for circular steel and aluminium square…

Q: For the figure shown, the neutral axis of reinforced concrete section .(2) is below that of section…

A: Answer: False The neutral axis id same for both section.

Q: Which of the following terms does not describe the process of designing and constructing sustainable…

A: concept- Sustainable buildings- A sustainable building is a different type of building. This…

Q: A simply supported beam is subjected to a triangularly distributed load of Q = 2.3 kN/m segment…

Q: For the beam shown, calculate the beam slope at A. Assume that a = 47 in., b = 161 in., c = 65 in.,…

A: In order to find the slope at A , we will use discontinuity equation of Bending moment to determine…

Q: Steel plates A PL % x 7 tension member is connected with three 1-inch-diameter bolts, as shown in…

Q: For the beam and loading shown, use discontinuity functions to compute (a) the slope of the beam at…

Q: Situation 5 - A 12-m simple beam supports a uniform load of 36 kN/m over 5 m from the left end.…

A: Given: Simply supported beam Loading To find: Maximum bending moment Shear force at mid span…

Q: Answer: 0A = B rad b C W C

Q: Q1) d- for the following equation, the value :of n is (n + 1)P3 = nP4 5 O 4 2.5 1 none of all above…

Q: PROBLEM SETS: A hollow member having the cross-section shown is to be formed from sheet metal of…

A: To find out the smallest dimension of d that can be used for maximum shearing stress not exceed to 5…

Q: uniformly distributed load is Ely = 8x^240x, then the beam length is

A: Given, beam loading equation, EI y = 8x2 - 40x

Q: A developer plans to extend Bayview Haven residential estate in Darwin by constructing a 3.5mm fill…

A: The given data is shown below: Fill thickness=3.5mClay thickness=5mDegree of…

Q: A tractor mounted ripper will be used for excavating a limestone having a seismic velocity of…

Q: Three building structure around the world that have installed thermal and moisture protection.…

A: Answer People living in hot regions wants to make their inside atmosphere very cool similarly people…

Q: REQUIREMENTS: CONCRETE MATERIALS (CLASS A) -bags cement -m° sand -m° gravel -gallons water

Q: How many 150 mm diameter, 7.5 mm thick disks can be fitted into a 120 mm long, 157.5 mm diameter…

A: Given:- The value of the diameter of the disk = 150 mm The thickness of the disk is 7.5 mm The…

Q: Truss members supporting a roof are connected to a 26-mm-thick gusset plate by an 18-mm diameter…

Q: 1.30 The lap joint is connected by three 20-mm-diameter rivets. Assuming that the axial load P= 50…

Q: For an element subjected to ox = 40 MPa and oy = 40 MPa, if the minimum principal stress is -40 MPa,…

Q: Q1. 11.3). Determine the moments at the supports A and C, then draw the Moment Diagran Assume joint…

A: Given :

Q: Kindly solve as fast as possible.

A: slope angle in this figure tan θ =1.5/1 θ=62.566° ∅ is not given so we assume ∅ value approx 0°…

Q: Q3) Ahom P = nstagnation m = pQ Ah0 = is obtained same as Q1 m|4h static nstatic P Ahstatic: V². V2…

Q: For the section shown, if d = 200 mm, horizontal shear force = 100 kN to the right and torque = 15…

A: To find out the total shear stress at B.

Q: Q3: For the stresses at the point shown, find the followings: 1- The maximum shear stress. 2- The…

Q: area by coordinate method.

A: In this question, we have to calculate area by coordinate method. X & Y coordinates are given in…

Q: A 1000g of sand has been soaked for at least 24hours prior to lab. After drying the sample to…

Q: In the figure below, the wood pole is supported by cables of 0.32-in diameter. The turnbuckles in…

Q: For the section shown, if a = 15 mm, b 30 mm, h = 120 mm, 1 = 7646787 mm^4 and M = 30 kN.m, then the…

Q: Situation 12-The bolt shown in Figure 503-56 S(06) is subjected to a total tensile force of 112 kN.…

A: Given, P = 112 kN

Q: An L = 39-ft-long soldier beam is used as a key component of an earth retention system at an…

A: Given data in question Span member length UVL Point load To find out Deflection at point C

Q: An aluminum alloy pipe with an outside diameter of 4.9 in. and a wall thickness of 6/16 in.…

Q: Question-A The channel index at irrigation outlet is 5/3. Find the value of setting for an orifice…

A: Given data- Channel Index = 5/3Orifice type outletTo Find-The value of setting

Q: Maria can do a job in 6 hours. Jhul can do the same job in 4 hours more while Vince can do it in…

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…

Q: The hydraulic conductivity, k of the clay for the loading range is 2.0 x 10^-4 ft^2/day. a) Find the…

Q: An elementary triangular concrete gravity dam, supporting 60 m height of reservoir water, should…

Q: Mang Tikyo wanted to know the width of cut of his moldboard plow with 0.70 ha per hr field capacity,…

A: Answer We are given Actual field capacity = 0.70 ha/hr Operating speed = 6.5 Kph Field efficiency…

Q: Question 3 A pair of lateral load is applied to a 3 m steel beam as in Figure Q3a to bend it…

A: L = 3m

Q: 1. From the figure shown, two blocks weighing 150 N and resting on a horizontal surface are to be…

Q: For the figure shown, if the stress in steel is 75 MPa, then the stress in the ****** .. copper is…

A: Given data in question Stress in steel Elasticity modulus To find out Stress in copper

Q: A representative calculation for a,, and an using Eq. (1.58) and (1.59) will be made for the sample…

Q: 42. A 30-m steel tape is used to measure the distance of a line. The measured distance is 457.65 m.…

Q: The annual peak flow data were recorded between 1980 and 2021 at a particular section of a river.…

A: AEP =It stands for annual exceedence probability. It is the probability during the return period,…

Q: A is 150 mm and the liquid flows in at the rate of 56 dm3 /s and has a specific gravity of 0.93. At…

Q: What does cause heat transfer?

A: The creation, utilization, transformation, and interchange of thermal energy (heat) across physical…

Question

PROBLEM SETS:
Equal torques are applied to thin-walled tubes of the same length L, same
thickness t, and same radius r. One of the tubes has been slit lengthwise
as shown, determine;
a) the ratio of their maximum shearing stress Tb/Ta
b) the ratio of the angle of twist of the shaft 0/0a
T
(b)
(a)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A hollow shaft transmits 15 MW at 400 rev / m * i * n . It is supposed that the maximum allowable stress is not to exceed 70 MN/m2 nor the angle per metre of twist 0.4 degree length of shafting. If the outside diameter of the shaft is 400 mm find the minimum thickness of the hollow shaft to satisfy the above conditions. G = 80 GN/m2. *
For the shaft shown, a. Determine the maximum stress on the shaft and the maximum angle of twist of end D relative to end A. b. If the stress in every section must not exceed 25 MPa, what should be the uniform diameter of the shaft? dAB = 100mm, dbc = 80mm, dcd = 50mm G for the shaft is 80GPa. Consider clockwise torques as negative.
A shaft 100mm in diameter and 3m long, with bult-in ends, is subjected to a clockwise torque of 4KN-m applied 1m from the left end, and to another clockwise torque of 16 KN-m applied 2m fromthe left end. 16. Compute for the shearing stress at segment AB. A. 61.12 MPa B. 20.37 MPa C. 40.74 MPa D. 30.30 MPa 17. Compute for the shearing stress at segment BC. A. 61.12 MPa B. 20.37 MPa C. 40.74 MPa D. 30.30 MPa 18. Compute for the shearing stress at segment CD. A. 61.12 MPa B. 20.37 MPa C. 40.74 MPa D. 30.30 MPa
A hoop shrunk onto a hallow tube exert a contact pressure of 3 ksi on the tube. An internal pressure of 10 ksi is then applied to the tube. The inner and outer radii of the tube are 1.5 in and 2.5 in, and 2.5 in and 4 in for the hoop. What is the maximum tangential strss in the tube after application of internal pressure? Also plot tangential stress variation diagram across the section.
The pipe shown has an innder diameter of 60 mm and an outer diameter of 75 mm. 80-N forces are applied as shown to develop a torque. The pipe AB is 1200 mm, and the material is steel with modulus E = 30 Msi. Problem: Determine the maximum shear stress developed in the material in the outer and inner walls along the central portion of the hollow pipe. How much angular rotation is exerted by the torque?
The stepped shaft ACB shown in Figure bellow is fixed at both ends and loaded by a torque TO at point C. Segment AC having solid circular cross section and segment CB having hollow circular cross section. If the shafts material is steel with shear modulus G = 11 x 10°psi, and the torque is To = 8,000 lb-in. Calculate: (a) The maximum and the minimum shear stress in segment CB. (b) The maximum and the minimum shear strain in segment CB. (c) The angle of rotation 0, at the cross section where the torque To is applied.
The shaft is supported by journal bearings at A and B that exert force components only in the x and z directions. Determine the smallest diameter of the shaft to the nearest 18 in. Use the maximum shear stress theory of failure with tallow = 6 ksi.
The bronze shaft is formed by attaching a hollow shaft to a solid shaft. The allowable shear stress of bronze is 100 MPa. Use G = 35 GPa for bronze. a. If the torque applied is 15 kN m, determine the maximum shearing stress developed in the bronze shaft b. Determine the maximum torque T that can be applied to the ends of the shaft without exceeding a shear stress of 100 MPa or an angle of twist of 3.5 in the 3.5-m length.
The turbine motor moving at 378 rev/ min can produce 2.5 hp. The shaft diameter is 1.25 inches. Calculate the torque and shearing stress developed in the shaft.
The turbine motor moving at 378 rev/min can produce 2.5 hp. The shaft diameter is 1.25 inches. Calculate the torque and shearing stress developed in the shaft.
Very very Urgent The distributed load q and the singular moment M act on the stepped shaft given in the figure. Draw the cross-sectional influence diagrams of the system under these forces. Determine the maximum stress value for the critical section. L1 = 226 mm ,L2 = 118 mm, a = 159 mm M = 572 N.m, q = 5 N/mm D = 51 mm , d1 = 19mm , d2 = 5 mm
STRENGTH OF MATERIALS A boiler is constructed of 9mm thick steel plates that are fastened together at their ends using a butt joint consisting of two 9mm cover plates and rivets having a diameter of 10mm and spaced 60mm apart as shown. If the stream pressure in the boiler is 1.38MPa, determine (a) the circumferential stress in the boiler's plate apart from the steam, (b) the circumferential stress in the outer cover plate along the rivet line a-a, and (c) the shear stress in the rivets. 60 mm 0.78 m