#1 1. The circuit below has the following specifications: C1 = 10 mF, C2 = 30 µF, C3 = 250mF, C4 = 80 mF, C5 = 90 µF, and V = 25 V(a) What is the equivalent capacitance of the circuit?(b) What is the total charge on each plate of C4?(c) What is the voltage across each of the capacito.2. Three capacitors 14µF, 16pF, 18µF are connected in parallel with an 8v.a. Determine the capacitance of the circuit.b. the charge on each capacitor.3. Three capacitors 14F, 16F, 18F are connected in series with an 8v.a. Determine the capacitance of the circuit.b. the charge on each capacitor

Answered: Image /qna-images/answer/93566891-0bf9-40a9-bcd9-7f9575278fcc.jpg

1. The circuit below has the following specifications: C1 = 10 mF, C2 = 30 µF, C3 = 250 mF, C4 = 80 mF. C5 = 90 µF, and V = 25 v (a) What is the equivalent capacitance of the circuit? (b) What is the total charge on each plate of C4? (c) What is the voltage across each of the capacito.

1. The circuit below has the following specifications: C1 = 10 mF, C2 = 30 µF, C3 = 250 mF, C4 = 80 mF. C5 = 90 µF, and V = 25 v (a) What is the equivalent capacitance of the circuit? (b) What is the total charge on each plate of C4? (c) What is the voltage across each of the capacito.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter20: Capacitance In Ac Circuits

Section: Chapter Questions

Problem 2PA: You are working in an industrial plant. You have been instructed to double the capacitance connected...

See similar textbooks

Related questions

Q: H.W. Find V. 40 20

A: As per our guidelines we are supposed to be answer only first question. Kindly repost the other ques...

Q: 950 ohms RL 10kO SAKey-A V1 25V D1 12% Vz= 15V When the varistor is set to 12, compute the following...

Q: List the differences between D-MOSFETs and E-MOSFETs.

Q: What is the angle by which I leads V in this circuit? 221UF 300 44.2uF 50V/0° 60HZ O 26.8 degrees O ...

A: First calculate capacitive reactances and than find equivalent impedance by combining the resistors ...

Q: 18. Determine V, for the negative logic OR gate of -5 V Si O V o Vo Si 1 kQ

Q: determine the minimum bandwidth and and baud for a BPSK modulator with a carrier frequecy of 40 MHz ...

Q: GENERAL SAFETY RULES FOR ELECTRICITY AND ELECTRONICS Safe practices will protect you and your fellow...

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you ar...

Q: Problem 2: Class E Amplifier Design A schematic of class E amplifier is shown in the figure 2 given ...

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you ar...

Q: 6) It is required to generate a single pulse waveform (Vtrigg) of 4 Volts amplitude (peak-to peak) a...

Q: b. The expression for the load current (i,) can be written as a function of the input voltage (v) an...

A: Use virtual ground concept.

Q: 20x ix 102 8 A 8Ω VB 1Ω VA (1). f )1 A UX +

Q: Si 4.7 k2 Ge Si 1.2 k2 +12 Vo -10 Vo GaAs 3.3 kS (a) (b) FIG. 2.159 Problem 9.

Q: he Norton equivalent circuit as seen by R,? Note that your answer should NOT be in ems of the unknow...

Q: 20. An electric iron draws 2.5 A at 230 V. Determin resistance. A. 78 ohms B. 84 ohms C. 92 ohms D. ...

Q: A 3A current source is now attached across the 6-2 resistor as shown With switch SW1 open, calculate...

Q: Find the average value of a half-wave rectified signal with a peak value of 20 mV.

A: We need to find average value for half wave rectifier

Q: What do you believe the challenges are for designers and manufacturers in packing billions of transi...

A: It is asked to tell the challenges are for designers and manufacturers in packing billions of transi...

Q: 3. Determine V, and Ip for the network of 2 kΩ Si +10 Vo- GaAs 2 k2 2 k2

Q: 13. Find the rms values of the following sinusoidal waveforms: a. v= 10 millivolts sin (377t + 60) b...

Q: Ex (2):-, If the number of binary bits = 3 and the sampling rate is 2 sample/sec find the signaling ...

A: SIGNALING RATE OR BIT RATE =nfs no of quantization levels=2^n

Q: a. From Figure 3, write node-voltage equations: one for each input terminal of the op amp. RA R3 OA1...

Q: What is the current in this circuit? 221UF 300 44.2uF 50V /0° 60HZ

Q: 1.A long shunt compound generator delivers 100A,250V at rated load. The resistances of the various w...

Q: a. What is the peak value of the waveform? b. What is the peak to peak value of the waveform? c. Wha...

A: One division in x axis is equal to 1 m sec and one subdivision is 0.2msec One division in y ax...

Q: 1. How you can recognize the heathy thyristor from the faulty one?

A: Note: As per the policy we can solve only one question, please re-upload the remaining question as a...

Q: Sketch output waveform the following CLIPPER circuits. Please show your solutions/analysis. 20 V 2V ...

Q: A half wave rectifier develops 10 V dc. What is the value of the ripple voltage? Vr(rms)=Blank 1 V

A: Ripple voltage = sqrt (rms voltage 2- average voltage2). For half wave rectifier average output volt...

Q: A compound motor develops a torque of 271 lb-ft when it is operating at 1200 rpm, under which condit...

Q: Sketch the RS-232 waveform that results from transmitting the binary value 10100011 over a 14,400-8-...

A: RS-232 Logic Waveform The above waveform applies to the Transmission and Receiving lines on the RS-2...

Q: Compute the oscillation frequency in Hz of a UJT based relaxation oscillator given the following: R1...

Q: The armature resistance of 220V shunt DC motor is 0.4 takes load armature of 2A and run at 1350 r.p....

Q: I 5a In

Q: A differentiator has an input of sin wt calculate the output voltage given the following values; R =...

A: Given: A differentiator which is having following values: Let input is a voltage signal, Input volta...

Q: Ignoring the provided value of β(120) draw the load line for the network of Fig. 4.118 on the charac...

Q: Determine the value of Vout from the figure below if: Rf = 42 kn Rin= 8 kn Vin = 7.56 V Vin Vout R1 ...

Q: For the Zener diode determine VI and Iz. R1 1 1k2 V1 D1 R2 | 30V 1kHz 0° 12V 1k2 Circuit F V-Rlank 1...

Q: T or F, modify the wrong part if False, please underline twice your answer if True or False. Th...

A: In this question we will write relation between field flux and current in dc series motor....

Q: 2. Calculate the equivalent impedance of tw parallel connected units, given that Z1 = 20@30°, and Z2...

Q: I=....A a- 3 I 18- b- 4 8 A с- 5 d- 6

A: Given circuit,

Q: In Figure 2.1, with switch SW1 closed, current I, = 2A. With switch SW1 open, what is the Norton equ...

Q: Derive the ABCD Constants for Medium (Nominal-pi method) and Long transmission line.

A: ABCD parameters- ABCD parameters basically describe the relation ( A mathematical relation ) between...

Q: 25 V t = 0 4 H Turn on the circuit and findt = 1,t = 2, t = 3, t = 4, t = 5

A: After turn on the switch , inductor and 2 ohm resistor become short.

Q: R 3kohms V1 R_L 20V D1 10KO 25% Key-A Vz= 8V When the varistor is set to 25%, compute the following ...

Q: Question 3 Refer to the circuit in Figure Q3: C=265.25 uF R = 52 L=39.79mH v = 85 sin (377t+10) V Fi...

A: Since you have asked multiple questions in a single request, we will be answering only the first thr...

Q: (b) The voltage limiter circuit shown below (Fig. Q.A1(b)) has been designed to prevent the output e...

Q: A synchronous generator having no-load frequency of 51HZ and droop constant of 0.5Hz/MW is synchroni...

A: Given a synchronous generator having, No load frequency, fnl=51 Hz Drop constant = 0.5 Hz/MW Slope =...

Q: ELECTRONIC CIRCUIT ANALYSIS AND DEVICES

Q: A 415V TPN busbar rising main chipped to a surface is to provide a 240V supply to each of 8 individu...

A: Answer - Following is the circuit arrangement showing how each flat must be connected to the rising...

Q: 4. The circuit uses current- (or shunt-) feedback bias. The Si transistor has ICEO = 0, VCEsat =0, a...

A: It is given that: ICEO=0VCEsat=0β=100RC=2kVCC=12V

Q: a. From the figure , write note voltage equations, one for each input terminal of the op amp b. The ...

A: Use virtual ground concept.

Concept explainers

KVL and KCL

KVL stands for Kirchhoff voltage law. KVL states that the total voltage drops around the loop in any closed electric circuit is equal to the sum of total voltage drop in the same closed loop.

Sign Convention

Science and technology incorporate some ideas and techniques of their own to understand a system skilfully and easily. These techniques are called conventions. For example: Sign conventions of mirrors are used to understand the phenomenon of reflection and refraction in an easier way.

Question

1. The circuit below has the following specifications: C1 = 10 mF, C2 = 30 µF, C3 = 250
mF, C4 = 80 mF, C5 = 90 µF, and V = 25 V
(a) What is the equivalent capacitance of the circuit?
(b) What is the total charge on each plate of C4?
(c) What is the voltage across each of the capacito.
2. Three capacitors 14µF, 16pF, 18µF are connected in parallel with an 8v.
a. Determine the capacitance of the circuit.
b. the charge on each capacitor.
3. Three capacitors 14F, 16F, 18F are connected in series with an 8v.
a. Determine the capacitance of the circuit.
b. the charge on each capacitor

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Three capacitors having capacitance values of 20F,40F, and 50F are connected in parallel to a 60 - Hz power line. An ammeter indicates a circuit current of 8.6 amperes. How much current is flowing through the 40F capacitor?
You are an electrician working in an industrial plant. You discover that the problem with a certain machine is a defective capacitor. The capacitor is connected to a 240-volt AC circuit. The information on the capacitor reveals that it has a capacitance value of 10 mF and a voltage rating of 240 VAC. The only 10-mF AC capacitor in the storeroom is marked with a voltage rating of 350 WVDC. Can this capacitor be used to replace the defective capacitor? Explain your answer.
Fill in all the missing values. Refer to the formulas that follow. Resistance Capacitance Time constant Total time 150 k 100 F 350 k 35 s 350 pF 10 s 0.05 F 1.2 M 0.47 F 12F 0.05 s 86 k 1.5 s 120 k 470 pF 250 nF 100 ms 8 F 150 s 100 k 150 ms 33 k 4 F =RCR=CC=R Totaltime=5
You find that a 25-F capacitor connected to 480 VAC is defective. The storeroom has no capacitors with a 480-VAC rating. However, you find two capacitors rated at 50 F and 370 VAC. Can these two capacitors be connected in such a manner that they can replace the defective capacitor? If yes, explain how they are connected and why the capacitors will not be damaged by the lower voltage rating. If no, explain why they cannot be used without damaging the capacitor.
You are a journeyman electrician working in an industrial plant. Your task is to connect an inductor to a 480-V, 60-Hz line. To determine the proper conductor and fuse size for this installation, you need to know the amount of current the inductor will draw from the line. The nameplate on the inductor indicates that it has an inductance of 0.1 H. An ohmmeter reveals that it has a wire resistance of 10 . How much current should this inductor draw when connected to the line?
A capacitor uses air as a dielectric and has a capacitance of 3 F. A dielectric material is inserted between the plates without changing the spacing, and the capacitance becomes 15 F. What is the dielectric constant of this material?
A pure capacitive circuit is connected to a 480-volt, 60-Hz power source. An ammeter indicates a current flow of 24 amperes. The circuit current must be reduced to 16 amperes by connecting a second capacitor in series with the first. What is the value of the existing capacitor? What value capacitor should be connected in series with the original capacitor to limit the circuit current to 16 amperes?
Three capacitors having values of 2.2 F, 280 F, and 470 pF are connected in parallel. What is the total capacitance?
A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating of 600 WVDC. The capacitor and resistor are connected to a 480-V, 60-Hz circuit. Is the voltage rating of the capacitor sufficient for this connection?