1. The cylinder of weight, W (see the table of values), shown below is being hoisted up with the force F against the vertical wall. If u, = 0.57 | W W = 500 kn a. Determine the reaction force (resultant of normal force and frictional force) against the vertical wall. b. Calculate the force, F, needed to set the cylindrical roller in motion.

1. The cylinder of weight, W (see the table of values), shown below is being hoisted up with the force F against the vertical wall. If u, = 0.57 | W W = 500 kn a. Determine the reaction force (resultant of normal force and frictional force) against the vertical wall. b. Calculate the force, F, needed to set the cylindrical roller in motion.

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter14: Sheet-pile Walls

Section: Chapter Questions

Problem 14.5P

See similar textbooks

Similar questions

The system in the figure is at 70°C (SG = 0.983). Determine the pressure at point C.
A rectangular gate AB in Figure 1 is 1.2 m long and 0.8 m into the paper. Neglecting atmospheric pressure effects, compute the force, F on the gate and its center of pressure position X.
Determine the magnitude of the projected component of the F = 120 lb force acting along the axis BC of the pipe. Suppose that a = 7 ft and h = 2 ft. Express your answer to three significant units and include the appropriate units
Calculate the horizontal displacement of point B. EI is constant for all members (p=50kN , W=90KN/m , h=7m , b=5 m) I need a solution within 40 min
Questions b and c. The pressure from part a is 0.86832 Mpa
A minimum force of P = 50 lb is required to hold the cylinder from slipping against the belt and the wall. Determine the weight of the cylinder if the coefficient of friction between the belt and cylinder is μs = 0.3 andslipping does not occur at the wall.
estimate the pressure at points A and B. (given the distance X=4.6m and Y=0.90m)
Fluid Mechanics Problem 1) A rectangular gate 3 meters high and 1.2 meters wide is hinged at the top. A force to keep the gate closed is applied at the bottom with an angle of 45 degrees with the veritcal. Compute the following if the water surface is 0.9 meters below the top of the gate. Use 9.81kN/m^3 as water's specific weight. a. the total hydrostatic force acting on the gate in kN. b. the distance of the total hydrostatic force measured from the liquid surface in meter. c. the magnitude of the force at the bottom of the gate in kN. 2) Use 9.81kN/m^3 as water's specific weight. Consider the rectangular gate shown in the figure. If the gate has a length of 2 meters, determine: a. the force exerted by the water on the left side of the gate in kN. b. the force exerted by the water on the right side of the gate in kN. c. the horizontal force at B required to turn the gate about the hinge in kN.
Determine the difference in pressure between points A and B.
Based on the following figure if the value of F is equal to 2541 N and the angle α is equal to 26.3°. Determine the minimum mass of the block A (in kg) so that it does not slide to the right product of the force F, if it is known that the static coefficient of friction is 0.25 and the dynamic is 0.2.
T (Shear force) and M (Bending) for the system whose loading condition is given in Figure 1.Draw the moment diagrams. Calculate the deflection (vertical displacement) at point B in mm using Castigliano's Theorem. The beam bending stiffness (EI) is constant along the bar and its value is 50 000 kNm2. q=1,4(kN/m) a=8(m) El=50000(kNm2)
Compute the magnitude of the resultant force on the indicated area and the location of the center pressure. Show the resultant force on the area and clearly dimension its location. From the figure