1. The following DA-DA converter circuit feeds 8 A DC motor, switching frequency is 10 kHz and transistor conduction time is 40 us. According to this; a. Plot the load voltage, T1 transistor current, and T1 transistor voltage for 2 periods in the time domain. b. Calculate the power transferred to the load. c. Show in which region the circuit works on the u-i plane and determine the mode in which the circuit works and present your explanation in detail.

1. The following DA-DA converter circuit feeds 8 A DC motor, switching frequency is 10 kHz and transistor conduction time is 40 us. According to this; a. Plot the load voltage, T1 transistor current, and T1 transistor voltage for 2 periods in the time domain. b. Calculate the power transferred to the load. c. Show in which region the circuit works on the u-i plane and determine the mode in which the circuit works and present your explanation in detail.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In the Buck - Boost DA-DA converter circuit, given below; 1) Source voltage (E) value: in the voltage range of [AB] (Volts) 2) Switching frequency (f) value: M kHz 3) Voltage between load terminals (Vload) F (Volt) 4) Capacitance value 470 (UF) 5) Load current lload) value: [KS] (Amps) current range The lowest Linductance value that can keep the DC-DC converter in continuous current condition under The lowest ripple (AIL) amount of the current passing through the coil (L) is given below in Amps. Which option do you see? A = 40 Volts B = 80 Volts M = 25kHz F = 55 Volts K = 10 Amps S = 25 Amps
In the Boost DA-DA circuit:Source voltage (E) value: in the range of [17-29] (volts),Switching frequency (f) value: 20 khz,Voltage between load ends: 40VCapacitance value: 470uFPower dissipated at load: 10 watts What is the lowest inductance L, in uH, that can keep the DC-DC converter in continuous current under these conditions? a) 269.3731 b) 415.4375 c) 364.8204 d) 163.6472 e) 578.1875
A base biased transistor circuit with the following element values is given VBB = 10V, VCC = 10V, RB = 470kΩ +/- 5%, RC = 820Ω, β = 100. Find the max and min values of base current. Type your equations and results ..
An ideal boost converter is required to have a constant output voltage of 12 V at 24 W load.The input voltage varies from 2.7 to 4.5 V (as in a battery cell). Select a switching frequency of100 kHz. The value of the inductance in the boost converter is 2.2 uH. Determine:(a) The range of duty cycle that the converter will operate with (hint: mode?), and(b) The minimum value of the output capacitance such that the pk-to-pk load voltage rippleis less than 2%.
2. a) Design a 9v DC oscillator circuit that produces a frequency of 500 Hz. The circuit may use a 555 timer or two transistor design(s). Show all calculations including the DC currents and bias voltages. Include the schematic and the required frequency formula(s). b) As a bonus, if a larger load were required to be connected to the chip, how would the schematic look and what components would be used to do design it? Also, as a theoretical approximation, if the 9v battery had a rating of 4 amp-hours, how long would it last powering this circuit? Show calculations to illustrate how you arrived at the answer.
A CCVT is connected to its rated primary source voltage of 138 kV. The valueof the capacitor from the high-voltage terminal to the tap point is 0.005 µF. The tap point voltage is 4kV. Find the value of the capacitor connected between the tap point and the ground terminal? Also,calculate the value of the tuning inductance for 50 Hz supply voltage.
FOLLOW UP QUESTIONS: BIPOLAR JUNCTION TRANSISTOR (BJT) SOLVE FOR: a.) VCE (off) CONSTRUCT A DC LINE SHOWING THE VALUES OF b.) IC (sat) c.) VCE (off) d.) ICQ e.) VCEQ
Values of Vg = 125 V, V0 = 75 V, f = 15 kHz, R = 10  are given for the buck converter.The switch, diode, coil and capacitor used are considered ideal. According to this:a) In order that the peak-to-peak value of the coil current ripple does not exceed 5% of the rated load current valuethe inductance (L) of the coil to be used and the average output voltage of the output voltage ripple.Calculate the capacity (C) of the capacitor that should be used to be 1% of the value. b) This circuit must be used for continuous transmission (CCM) operation at 50% load.Find the minimum inductance value.
An 8-bit A/D converter has VFS= 5 V. What is the digital output code word for an input of 1.2 V? What is the voltage range corresponding to 1 LSB of the converter?
Consider the following circuit. Calculate the output voltage when VGS=0 and VGS=-10V. Also, calculate the on-off ratio.
Determine the point Q for the JFET circuit shown and perform the curve transfer showing that point. We have the following data from the different elements of the circuit such as: RG = 10 MΩ, RD = 3.3 kΩ, RS = 780 Ω and powered by a 9 volt source. The manufacturer's sheet indicates that it has IDSS = 4 mA and VP = −6 V. Include transfer characteristic graph.
The input resistance of the amplifier used in the oscillator circuit shown in the picture is very large. No-load voltage gain is given as K0 = 5. For L = 0.1mH; Calculate the value of C1 and C2 capacitors for the circuit to oscillate at f0 = 2MHZ.