1. The hydraulic lift (the figure below) has a small piston with the surface A,in = 0.04 m? and a large piston with the surface Aout = 7 m?. 19 N. in F. out F Aout Ain (a) When the small piston is pushed down, the pressure in the fluid is: (b) What force will the large piston provide if the small piston in a hydraulic lift is moved down as shown in the figure? F, N out in

1. The hydraulic lift (the figure below) has a small piston with the surface A,in = 0.04 m? and a large piston with the surface Aout = 7 m?. 19 N. in F. out F Aout Ain (a) When the small piston is pushed down, the pressure in the fluid is: (b) What force will the large piston provide if the small piston in a hydraulic lift is moved down as shown in the figure? F, N out in

Physics for Scientists and Engineers, Technology Update (No access codes included)

9th Edition

ISBN:9781305116399

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter14: Fluid Mechanics

Section: Chapter Questions

Problem 14.8P: The small piston of a hydraulic lift (Fig. P14.8) has a cross-sectional area of 3.00 cm2, and its...

See similar textbooks

Similar questions

What is the difference between flow rate and fluid velocity? How are they related?
Explain why the fluid reaches equal levels on either side of a manometer if both sides are open to the atmosphere, even if the tubes are of different diameters.
Is there a limit to the height to which an entrainment device can raise a fluid? Explain your answer.
Oil having a density of 930 kg/m3 floats on water. A rectangular block of wood 4.00 cm high and with a density of 960 kg/m3 floats partly in the oil and partly in the water. The oil completely covers the block. How far below the interface between the two liquids is the bottom of the block?
The hydraulic system of a backhoe is used to lift a load as shown in Figure 11.45. (a) Calculate the force F the slave cylinder must exert to support the 400-kg load and the 150-kg brace and shovel. (b) What is the pressure in the hydraulic fluid if the slave cylinder is 2.50 cm in diameter? (c) What force would you have to exert on a lever with a mechanical advantage of 5.00 acting on a master cylinder 0.800 cm in diameter to create this pressure? Figure 11.45 Hydraulic and mechanical lever systems are used in heavy machinery such as this back hoe.
Water emerges straight down from a faucet with a 1.80-cm diameter at a speed of 0.500 m/s. (Because of the construction of the faucet, there is no variation in speed across the stream.) (a) What is flow rate in cm3/s? (b) What is the diameter of the stream 0.200 m below the faucet? Neglect any effects due to surface tension.
How do you convert pressure units like millimeters of mercury, centimeters of water, and inches of mercury into units like newtons per meter squared without resorting to a table of pressure conversion factors?
Archimedes' principle can be used to calculate the density of a fluid as well as that of a solid. Suppose a chunk of iron with a mass of 390.0 g in air is found to have an apparent mass of 350.5 g when completely submerged in an unknown liquid. (a) What mass of fluid does the iron displace? (b) What is the volume of iron, using its density as given Table 14.1? (c) Calculate the fluid's density and identify it.
Gasoline is piped underground from refineries to major users. The flow rate is 3.00102m3/s (about 500 gal/min), viscosity of gasoline is 3.00102m3/s , and its density is 680 kg/m3. (a) What minimum diameter must be pipe have if the Reynolds number is to be less 2000? (b) What pressure difference must be along each kilometer of be pipe to maintain flow rate?
What fraction of ice is submerged when it floats in freshwater, given the density of water 0°C is very close to 1000 kg/m3?
Figure 11.35(a) shows the effect of tube radius on the height to which capillary action can raise a fluid. (a) Calculate the height h for water in a glass tube with a radius of 0.900 cm—a rather large tube like the one on the left. (b) What is the radius of the glass tube on the right if it raises water to 4.00 cm?
The small piston of a hydraulic lift (Fig. P14.8) has a cross-sectional area of 3.00 cm2, and its large piston has a cross-sectional area of 200 cm2. What downward force of magnitude F1 must be applied to the small piston for the lift to raise a load whose weight is Fg = 15.0 kN?