1. Three non-inductive resistances, each of 100 Q, are connected in star to a three-phase, abc-sequence, 440-V supply. Three inductive coils, each of reactance100 2 connected in delta are also connected to the supply. Three wattmetersare connected as in Example 2.1.18. Calculate the reading indicated by eachwattmeter.

Wattmeter will indicate only real power. Power indicated by each wattmeter is the real power of each…

1. Three non-inductive resistances, each of 100 Q, are connected in star to a three- phase, abc-sequence, 440-V supply. Three inductive coils, each of reactance 100 Q connected in delta are also connected to the supply. Three wattmeters are connected as in Example 2.1.18. Calculate the reading indicated by each wattmeter.

1. Three non-inductive resistances, each of 100 Q, are connected in star to a three- phase, abc-sequence, 440-V supply. Three inductive coils, each of reactance 100 Q connected in delta are also connected to the supply. Three wattmeters are connected as in Example 2.1.18. Calculate the reading indicated by each wattmeter.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.31P: Consider two interconnected voltage sources connected by a line of impedance Z=jX, as shown in...

See similar textbooks

Similar questions

In a string of three identical suspension insulator units supporting transmission line conductor.if the self capacitance of each unit is debited as C farads, The capacitance of each connector pin to ground can be taken as 0.1C farad's. If the maximum permissible voltage per unit is given as 20 kva then calculate A.maximum safe working voltage B.string efficiency
Which of these can be installed without needing an electrical permit first? A. Hot tubB. Bank of lights at a football stadiumC. Building security system D. Basement furnace
Consider two interconnected voltage sources connected by a line of impedance Z=jX, as shown in Figure 2.27. (a) Obtain expressions for P12 and Q12. (b) Determine the maximum power transfer and the condition for it to
Consider the balanced three-phase system shown in Figure 2.34. Deter mine v1(t) and i2(t). Assume positive phase sequence.
For the circuit element of Problem 2.3, calculate (a) the instantaneous power absorbed, (b) the real power (state whether it is delivered or absorbed). (c) the reactive power (state whether delivered or absorbed). (d) the power factor (state whether lagging or leading). [Note: By convention the power factor cos() is positive. If | | is greater than 90, then the reference direction for current may be reversed, resulting in a positive value of cos() ].
Which of the following statement is wrong for single phase AC distribution system? 1the drop is the sum of moments of I cos φ and I sin φ components with distances equal to resistance and reactance respectively. 2the distance of separation between wires is relatively smaller as compared to overhead line. 3the net drop is the difference of the drop in reactance due to the quadrature component and in resistance due to inphase component of current. 4the inphase and quadrature components of current contribute to the voltage drop. 5the resistance component is normally higher than the inductive reactance component.
Consider a house that has a 120V mains with mains frequencyof 60hz and a service current of 100A, which follows the safety standards of theresidential facilities.(a) Calculate the maximum power capacity.(b) Within the safety limit, the following devices can all operate at the sametime? If yes, what is the total power consumed? If not, what happens if all devicesare turned on at the same time and suggest a solution to the problem?- 4800W clothes dryer.- 400W washing machine.- 1200W dishwasher.- 1000W iron.- 860W air conditioning.- 150W color television.- 110W stereo sound.- 2400W electric stove.- 1200W microwave oven.- 1800W cooler.(c) Assuming that 60% of the maximum power were used daily, what is the total costper month for a kWh value of 10 cents?(d) Sketch the waveform, determine the phase difference and calculate the rms values of thefollowing waveforms: v(t) = 60 sin(wt + 20) and i(t) = 12 sin(wt - 20).
A 210V, 50 Hz, single phase radial distribution system, the resistance of the wire is 0.0008 ohm/m supply and return. Two loads are connected and it consumes 10 and 10 A respectively and are fed from the cable at distance of 15 and 15 respectively. Calculate the voltage available across load 1 and 2
You are a journeyman electrician in an industrial plant. You have been assigned the task of connecting a 25-kW electric heater to a 240-V, single-phase panel. The heater is located in an area with an ambient temperature of 90°F. The conductors are to be copper with Type TW insulation. The heater is expected to operate for more than three hours at a time. What size conductors would you use to connect this heater? Is this correct? I=P/EI=25000 W/ 240 VI= 104.17 amps x 125%I= 130.21 amp/ .96I= 135.63 amp2/0 AWG conductor will be needed
The following data were obtained from a short-circuit test performed upon a 50 kVA, 2300/115 V, 60 Hz transformer: Esc = 87 V, Isc = 21.75 A, Psc = 590 W. Calculate (a) equivalent resistance, reactance and impedance referred to the primary, and (b) voltage regulation at a power factor of 0.866 lagging. Subject: Electrical Apparatus and Devices
For transferring electrical power at 220 kV, six conductors of ACSR Drake constitute a 60Hz double circuit three phase line arranged as shown below. The vertical spacing between consecutive conductors is 14ft; the longer horizontal distance is 32ft whereas the shorter horizontal distance is 25ft. a. Find the inductance per phase per mile and the inductive reactance per phase in ohms per mile. b. Find the capacitive reactance to neutral in ohm-miles. c. Find the resistance per phase per mile in ohms per miles. d. If the length of the line is 90 miles then draw an equivalent circuit of the line and analyse the open circuit and short circuit performance of the line. e. Find the maximum power we can transmit over the line. f. If the line is delivering power to a load of 20MW at 0.8 power factor lagging then find the voltage at the receiving end of the line. Also, Determine the voltage regulation, losses and efficiency of the line. g. If a fixed shunt compensation of 3 MVAr is attached at…
A power plant produces 1000MW to supply a city 40km away. Current flows from the power plant on a single wire with resistance through the city and returns via the ground, with negligible resistance. At the power plant the voltage between wire and ground is 115 kV. Determine: (a) the current in the wire, and (b) the fraction of the power lost in transmission.