1. Using the Right-Side Elevation, determine the quantity of brick required to place the brick veneer face. The brick chosen will lay at a rate of 7 brick per square foot of wall area.

Q: A uniformly distributed load of 4 kN/m, 6 m long crosses a girder 24 m long. What is the maximum…

A: Calculate the maximum bending moment

Q: Explain bubinga wood, is there any wood like it?

A: Bubinga is a type of hardwood that is highly valued for its beauty, durability, and strength. It is…

Q: Question 1 A highway survey PI falls in a ponc the tangents. In the triangle formed and at B=…

A:

Q: 21 Determine the horizontal displacement of joint B of the steel truss shown in Fig.3 is A 400 mm²,…

A:

Q: 4. Given the inlet below, with h=0.5 ft, W=1.5 ft, L=4.0 ft, and a gutter depression depth=0.33 ft,…

A: The value of "h" = 0.5 ft The value of "W" = 1.5 ft The value of "L" = 4 ft The gutter depression…

Q: Problem 2: A composite shaft is composed of a solid section AB and a tubular section BC, both of…

A:

Q: 18' w K K. 6'

A:

Q: 3 Open traverse Line BC Line CD Line BA N Line CB Find the bearing and azimuth Line AB Line DC A حدا…

A:

Q: What is the surface area (m²) of settling tank used for design discharge of 1.5 m³/s? (Assume design…

A: Given data   Design discharge= 1.5 m3/s  Overflow rate  40 m3/m2/d Find surface area

Q: rectangular gravity dam has a height 5 m. It retains 3 m deep of water. Calculate the minimum width…

A: Factor of safety = 1.5 Coefficient of friction = 0.5 Specific gravity of concrete = 2.4 Water retain…

Q: The equilibrium discharge (in cumecs) of the S-curve derived from a 5-h unit hydrograph for this…

A: 5-h unit hydrograph Area A=860 km2

Q: Q.2(a) In a falling head permeability test on a 120 mm high and 100 mm diameter cylindrical sample,…

A: Falling head permeability test is used to find the permeability of fine grained soil. Given:…

Q: Determine the displacements and the slopes at the nodes, the forces in each element, and the…

A: Elastic constant,E = 29 × 106 psi  I = 150 in4  By using Matrix method

Q: 4.9 through 4.11 Two vertical forces are applied to a beam of the cross section shown. Determine the…

A:

Q: E10.13 Selection of material and shape to suppress buckling. Cylindrical tubing is available from…

A: In the simplest form of Euler buckling, the middle (along the column's length) deflects to one side…

Q: Analysis this graph explaining the relationship between the head loss and velocity

A: Given the graph plotted Head loss v/s  Velocity and it is asked to Analysis this graph explaining…

Q: The pressure of a medium is changed from 1.01 x 105 Pa to 1.250 × 105 Pa and decrease is volume is…

A: Initial pressure- Pi=1.01×105 Pa Final Pressure- Po=1.25×105 Pa Decrease in volume=20% Temperature…

Q: Find shear and moment digram

A:

Q: What does "pattern" really imply in the context of construction design? How are these three…

A: Construction design refers to the process of creating a plan or blueprint for a building or…

Q: Determine the yield modulus of elasticity and yield strength of an aluminum material with the…

A: The stress is taken in y-axis and strain in x-axis. From the data, stress-strain curve are being…

Q: Linear regression analysis was performed on a set of traffic data using speed and density…

A: Take speed and density as y and x respectively; Given equation: y=57.5-0.457x

Q: 6-22. The compound beam is subjected to a uniform dead load of 0.8 kN/m and a single concentrated…

A:

Q: nitial prestressing force of 700 kN at an eccentricity of 350 mm at midspan, stress at op fibre at…

A:

Q: Consider the beam shown in (Figure 1). Suppose that P = 9 kip. w = 1.7 kip/ft. Point E is just to…

A:

Q: Design the flexural reinforcement for a rectangular section with a width of 10 in. and a total…

A: Width = 10 in. Depth = 20 in. Md= 88 k-ft Ml= 70 K-ft fc= 6 ksi fy=80 ksi

Q: в Close traverse Find the total area Өв 5 Чт m. 3.3 BA с A ӨС 2.78 6.45 3.56 8-60 т. m ODI ш ВЕ 7.1…

A:

Q: MAT 1:1,5 30 meter 4m q=1.2 t/m² Ymbunan 1.67 t/m³ Yat = 1.72 t/m³ 0.5 Z 0.75 Z 4 meter M Z= 6 meter…

A:

Q: Two steel plates with thicknesses of 16 mm and 18 mm are connected together using four 12 mm bolts.…

A:

Q: The local mean time at a place located in longitude 90° 40'E when the standard time is 6 h 30 min…

A: Longitude of standard meridian = 90°40' E Longitude of place = 82°30' E Standard time = 6h30min.

Q: 1. Dikes are to be installed on both channel banks of the 1.2 km long river section. The river width…

A: length of river -1.2 km Width of river - 60 m Angle - 10 degrees To determine- numbers of dikes…

Q: Can I get a step by step on how to answer? Convert 168 mg/m^3 of SO2 to ppm at 25°C and 101.325 kPa…

A: Given:- 168 mg/m³ of SO2, T= 25°C P= 101.325kPa

Q: Activity 1. Solve the problems below and use NSCP 2001 limitations/specifications. Show your…

A: d=375 mm b=375 mm Cc=75 mm fy=345 MPa fc'=21 MPa As=3-22 mm ∅ bar

Q: Q4. An L-shaped beam is being supported by a ball and socket support at O and two cables, AB and CD.…

A:

Q: Design the required tension steel reinforcement at the critical rectangular section of the shown 3.0…

A: Cantilever beam with span = 3 m  Service Dead Load,wd= 15 KN/m  Service Live Load,wL = 20 KN/m  F'c…

Q: You have a run of overhead irrigation pipe that has 20 sprinkler heads in a 600-foot row (one every…

A: Length of the row: L=600 ftd Width of the row: B=40 ft Each sprinkle discharge rate: 3 Gallons/min…

Q: Assuming a reverse curve with the following parameters: Tangent @ Curve 1 = 40m Deflection Angle…

A: Tangent @ Curve 1 = 40 m Deflection Angle from PC to PRC = 60 degrees Stationing of the PC = 0+000…

Q: Q.2 What will be the capillary rise observed in a capillary of diameter 3mm inserted in water bath,…

A: Diameters- d1=2 mmd2=3 mm&h1=1.5 cm

Q: 7.6 and 7.7 Use the virtual work method to determine the vertical deflection at joint C of the truss…

A: E = 29000 ksi  Determine the vertical deflection at joint C using virtual work method.

Q: In a horizontally held injection syringe, the piston of 0.2 cm² cross-sectional area is pushed at a…

A:

Q: What type of polymer: elastomer (rubber), thermoplastic, or thermoset exhibit low creep? Explain wh

A: The creep refers to a solid deforming permanently below its yield point when subjected to continuous…

Q: A portion of a mechanical coin sorter works as follows: Pennies and dimes roll down the 29 degrees…

A: Let us first draw the free body diagram based on the given data On Considering Moment about O, we…

Q: (2) * 28" 2#8 14" I2.5" NwC fé=3000 psi > 2 #10 z 2 #11 I 3" Grade 60 steel &Mn = ?

A:

Q: D 400 mm- 6 KN 4 kN 400 mm 400 mm H 300 mm + 300 mm

A: To find Force in member FH, GH and GI

Q: What units are used to indicate the lag time measurement result?

A: This question is related to the Unit hydrograph from Hydrology from Civil Engineering. In this…

Q: Calculate the potential evapotranspiration from an area near the Philippines in the month of August…

A: The following data are available:- Latitude = 13°5’N Temperature = 23°C Relative humidity = 69% n =…

Q: d W.S. 22.5KN 60⁰ pulley 5m hinged (Width normal to paper -2.8m)

A:

Q: 3.2 Consider the basic system of Fig 2-1a with the following properties: m = 2 kips-sec²/in and k =…

A: m = 2 kips·sec2/in k = 20 kips/in The system is subjected to resonant harmonic loading (ω = ω)…

Q: If the overhanging beam is made of wood having the allowable tensile and compressive stresses of…

A:

Q: For the beam structure shown, compute the reactions and draw shear and bending moment diagrams.…

A: Given Propped cantilever beam with triangular load acting of magnitude 4 kN/m It is asked to compute…

Q: (2) 28"/ 2#8 14" I2.5" NwC fé=3000 psi > 2 #10 z 2 #11 I 3" Grade 60 steel &M=?

A: h = 28 in b = 14 in d' = 2.5 in fc = 3 ksi fy = 60 ksi tension bars, 2#10, 2#11 compression bars,…