1. Water flows through a horizontal, 0.5-m-diameter pipe at a rate of 0.9 m³/s (Figure below). It is ejected from the pipe through a 0.25-m-diameter nozzle. Determine the force (F) that holds the nozzle in place if the water pressure in the pipe just upstream of the nozzle is 283 kN/m² (kPa). F pl V₁. in F Vout

1. Water flows through a horizontal, 0.5-m-diameter pipe at a rate of 0.9 m³/s (Figure below). It is ejected from the pipe through a 0.25-m-diameter nozzle. Determine the force (F) that holds the nozzle in place if the water pressure in the pipe just upstream of the nozzle is 283 kN/m² (kPa). F pl V₁. in F Vout

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Water at 20°C flows through a 300-mm-diameter pipe that discharg sphere as shown in Figure 4.61, When a partially open val the top of the pipe, the flow rate in the pipe is 0.2 m*s and the (gauge) pressure just upstream of the valve is 600 kPa. Estimate the force partially open valve, es into the atmo- ve extends 200 mm from exerted by the water on the —Valve 0.2 mYs —» Atmosphere Figure
Hydraulics ProblemAn open horizontal tank 1.5m high 2m wide and 5m long is full of oil with a specific gravity of 0.9. It is accelerated in the direction parallel to the longer length at 2.3 m/s2 a. What is the force acting on the wall of the tank with the shortest depth in KN? b. If the acceleration is increased by 0.88 m/s2. Determine the volume of oil that spilled out the tank?Note: Draw free-body diagram and used 4 decimal places
A 3 m diameter , 7 m long cylindrical tank is completely filled with water. The tank is pulled by a truck on a level road with 7 m long axis being horizontal. Determine the pressure difference in kPa between the front and back ends of the tank along a horizontal line when the truck decelrates at 4 m/s^2.
Water at 15°C (? = 999.1 kg/m3 and ? = 1.138 × 10−3 kg/m·s) is flowing steadily in a 30-m-long and 6-cm-diameter horizontal pipe made of stainless steel at a rate of 10 L/s. Determine (a) the pressure drop, (b) the head loss, and (c) the pumping power requirement to overcome this pressure drop.
A tank containing water moves horizontally (parallel to length) with a constant linear acceleration of 3 m/s2 . The tank is 3 m long and the depth of water when the tank is at rest is 1.5 m. (a) What angle (degrees) does the water make during acceleration? (b) What is the minimum height of the vessel for no spilling of water? (c) What is the maximum pressure head (m)?
The siphon in Fig. is used to draw water from the large open tank. If the absolute vapor pressure for the water is p = 0.91 kPa, determine the shortest drop length L of the 40 mm diameter tube that will cause cavitation in the tube. Draw the energy and hydraulic grade lines for the tube.
With the chamber-pipe system in the figure, the ideal fluid (water) taken from the infinitely sized chamber A is poured into the atmosphere with a 40 cm fixed diameter BCDEF pipe. Since zB=29, zC=10, zD=28.5, zE=5 and zF=28 meters according to the comparison plane;a) Calculate the flow of the system.b) Draw the relative load (energy) and piezometer lines of the system.c) Determine where the greatest pressure will be observed throughout the system and calculate its relative value.
1. A long siphon connected at the side near the bottom of the reservoir discharges water through a nozzle 200mm by 50 mm creating a jet. Various points were identified located along the siphon: Point A is located after the reservoir connection, Point B is 4 m above Point A, Point C is 3 m above Point A, and Point D is 1 m below Point A and located before the nozzle. Determine the flow in m3/s along the siphon and the pressure in kPa at Point A, Point B, Point C, and Point D. Consider that the level of the reservoir is same with Point C. Assume no head loss along the siphon. 2. Two interconnected pipes A and B with 300 mm and 200 mm diameter, respectively, carries a flow of 0.116 m3/s. Determine the velocity in m/s of pipe A and pipe B. If pipe B was replaced with 400 mm diameter, determine the velocity in m/s of pipe B. 3. The 500 mm diameter pipe conveys treated water to supply a municipality with a demand of 40 MLD. Determine the head loss in meter if the length of the pipe is 10 km…
An open circular cylinder with 2m of water is acted upon by an unbalanced upward force of 20 kN. The volume of water inside the cylinder is 6.28 m^3. a. Compute the acceleration of the tank. b. Compute the pressure at the bottom of the tank.
The flowrate of water through the bend pipe (90o) is 0.21 m3/s. The pipe diameter at the inlet is 150 mm and the outlet diameter is 75 mm. The outlet is higher than the inlet by 2 m. Frictional losses in the pipe is equal a loss factor of 0.5 applied to the inlet velocity head. The pressure head at the inlet is 8.6 m and the volume of water in the bend is 0.6 m3. Calculate the resultant force and its direction.
Obtain the gage pressure at the center A of the pipe shown. Neglect surface tension effects. For Liquid 1 specific gravity= 1.5, for liquid 2 specific gravity= 3.2, h1=15cm, h2= 30cm,h3=75cm
An open rectangular tank 2.2m in length contains 16m^3 of gasoling (sg=0.70) and 23m^3 of water. The fluid is arranged in two stable layers. Determine the total hydrostatic force(kN) on one of the two smaller vertical sides of the the tank.