A 30-mm thick AISI 1020 steel plate is sandwiched between two 10-mm thick 2024-T3 aluminum plates and compressed with a bolt and nut with no washers. The bolt is M10 x 1.5, property class 5.8. (a) Determine a suitable length for the bolt, rounded up to the nearest 5 mm. (b) Determine the bolt stiffness. (c) Determine the stiffness of the members.

A 30-mm thick AISI 1020 steel plate is sandwiched between two 10-mm thick 2024-T3 aluminum plates and compressed with a bolt and nut with no washers. The bolt is M10 x 1.5, property class 5.8. (a) Determine a suitable length for the bolt, rounded up to the nearest 5 mm. (b) Determine the bolt stiffness. (c) Determine the stiffness of the members.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter8: Eccentric Connections

Section: Chapter Questions

Problem 8.2.10P

See similar textbooks

Similar questions

An A36 steel plate with width of 400 mm and thickness of 12 mm is to beconnected to a plate of the same width and thickness by 34 mm diametersbolts, as shown in the figure (next slide). The holes are 2 mm larger thanthe bolt diameter. The yield strength of the steel plate is Fy = 248 MPa.Assume allowable tensile stress on net area is 0.60Fy. It is required todetermine the value of b such that the net width along bolts 1-2-3-4 isequal to the net width along bolts 1-2-4.a. Calculate the value of b in mm.b. Calculate the value of the net area for tension in plates in mm².c. Calculate the value of P so that the allowable tensile stress on net areawill not be exceeded.(Use at least 2 decimal points on your answers.)
Determine the design tensile strength of plate (200x8 mm) connected to 10-mm thick gusset using 20 mm bolts as shown in the figure, if the yield and the ultimate stress of the steel used are 250 MPa and 410 MPa, respectively. Add 1mm around the bolt for the hole. Use LRFD method. Plate 8-mm thick 2 3 40+ 30 301 T 200 mm Gusset 10-mm thick 3af 30 2_3 *40 40+ 50,54 +40
One bolt 34 in-16 UNF × 2 12 in. SAE grade 5 is subjected to a P load of 6 kip at atension joint. The initial stress is Fi = 25 kip. The stiffness of the bolt and the joint are kb = 6.50and km = 13.8 Mlbf / in, respectively.a) Determine the preload and service load stresses on the bolt. Compare them withthe minimum SAE test strength of the bolt.
Plate connection with bolts with shear strength value T=200 MPA is given in the figure. Determine the minimum required bolt diameter for the safe transfer of the P=70 kN load.
Two plates each with thickness t= 16 mm are bolted together with 6-22mm bolts forming a lap connection. Bolt spacing are as follows: S1=40 mm, S2=80 mm, S3=100 mm. Bolt hole diameter= 25mm. (a)Compute the bearing stress of the bolt and hole if the P = 200KN. (b)If allowable bearing stress is 480MPa, compute the value of P.
An A36 angle bar is used as a tension member connected on both legs with 22 mm diameter bolts. Given that s = 50 mm, calculate the design strength (kN) by LRFD with the limiting state of tensile fracture at the smallest possible net area. Write your answer to the nearest whole number. Ag = 1,852 mm2 t = 8 mm
Calculate the tightening torque for an SAE 5, ASTM449, 13UNC grade bolt with a diameter of 1/2 inch. Also determine the tensile stress and torsional stress. Indicate on the Mohr circle the principal stresses in the bolt and determine the factor of safety FS.
An A36 angle bar is used as a tension member connected on both legs with 17 mm . Given that s = 49 mm, calculate the design strength (kN) by LRFD with the limiting state of tensile yielding in the gross area. Write your answer to the nearest whole number. Ag = 1,852 mm2 t = 8 mm
Load and resistance Factor design-tension members Q- Look into the block shear failure mode on the angle L4X4X linked to the 1-inch gusset plate with three 1-inch diameter bolts. Steel A36 is the substance.
A bolted lap joint is used to connect a rectangular bar to a hanger bracket, as shown in Fig. P2.8-2. If the allowable shear stress in the bolt is 80 MPa, and the diameter of the bolt shank 15 mm, what is the allowable tensile load on the rectangular bar, Pallow., in kN?
Topic: COMBINED STRESS-AXIAL TENSION AND FLEXURE BENDING: STEEL DESIGN Please solve your Solution in a handwritten Note: It should be handwritten pleaseeee Questions A Tension member with no holes is subjected to axial loads of PD=68kN & PL=64kN.It is also subjected with bending moments of MDy=40kN-m & MLy=55kN-m. Is themember adequate? Steel is of A992 Gr 50 Specs. Use LRFD. Neglect the weight of the beam. Section properties:Lp = 1.863 md=459.99mmtw=9.02mmzx= 1835x10^3 mm^4Lr = 5.305 mLb = 4.8 mbf=191.26mmtf=16mmSx=1611x10^3 mm^4 Sy=195x10^3 mm^4Zy=303x 10^3 mm^4 Cb=1.32
Topic:Bolted Steel Connection - Civil Engineering -Steel Design *Use latest NSCP/NSCP 2015 formula to solve this problem *Please use hand written to solve this problem A 12.5 mm x150 mm plate is connected to a gusset plate having a thickness of 9.5 mm.Diameter of bolt = 20 mm Both the tension member and the gusset plate are of A 36 steel. Fy = 248 MPa, FU = 400 MPa. Shear stress of bolt Fnv = 300MPa. Questions: a.Determine the shear strength of the connection. b.Determine the bearing strength of the connection. c. Determine the block shear strength of the connection.