1. What is the phase relationship between R, L, and C components in a series AC circuit? 2. What is the relationship between inductive reactance and frequency? 3. What is the relationship between capacitive reactance and frequency? 4. What is the effect of the frequency in series circuit? CONCLUSION:

1. What is the phase relationship between R, L, and C components in a series AC circuit? 2. What is the relationship between inductive reactance and frequency? 3. What is the relationship between capacitive reactance and frequency? 4. What is the effect of the frequency in series circuit? CONCLUSION:

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter5: Transmission Lines: Steady-state Operation

Section: Chapter Questions

Problem 5.25MCQ

See similar textbooks

Similar questions

Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor, and a 4 capacitor. (a) Draw the circuit diagram. (b) Compute the series impedance. (C) Determine the current I delivered by the source. Is the current lagging or leading the source voltage? What is the power factor of this circuit?
For the single-phase circuit shown in Figure 122,I=100A. (a) Compute the phasors I1,I2, (b) Draw a phasor diagram showing I,I1,I2, and V
The power factor for a capacitive circuit (R-C load), in which the current leads the voltage, is said to be (a) Lagging (b) Leading (c) One
A 60Hz, single-phase source with V=27730 volts is applied to a circuit element. (a) Determine the instantaneous source voltage. Also determine the phasor and instantaneous currents entering the positive terminal if the circuit element is (b) a 20 resistor. (C) a 10mH inductor, and (d) a capacitor with 25 reactance.
The instantaneous power absorbed by the load in a single-phase ac circuit, for a general R LC load under sinusoidal-steady-state excitation. is (a) Nonzero constant (b) Zero (c) Containing double-frequency components
1- Explain why the phasor and the impedance have the same angle. 2- Compare the result for utilized different frequency in same circuit. 3- Give example to utilize the RLC circuit. 4- In general, how would the phasor diagram of Figure 4.1 change if the frequency was raised? 5- In general, how would the phasor diagram of Figure 4.4 change if the frequency was lowered?
Sketch the phasor diagram of the above circuit in terms of impedance, voltage, and the power triangle.
When you are converting an instantaneous current to a phasor, how does the phase angle being positive or negative affect solving the problem i.e. the representation being (wt - the phase angle in degrees) or (wt + the phase angle in degrees)?
A circuit consists of an AC voltage source, a 10-ohm resistor, and a capacitor, all connected in series. The magnitude of the impedance of the capacitor is also 10 ohms. Which of the following is true about the source voltage and the current through the circuit? a. Insufficient information is given. b. The source voltage will lag the current. c. The source voltage will lead the current. d. The source voltage will be in-phase with the current.
A 120V adjustable frequency ac source is connected in series with a resistor, an inductor, and a capacitor. At 60Hz, the resistance is 5 ohms, the inductive reactance is 3 ohms, and the capacitive reactance is 4 ohms. Compute: (a)load impedance at 60Hz (b) value of the capacitance and inductance Explain each step. Please recheck
A capacitor and a resistor are connected in parallel to a 120-V, 60-Hz line. The resistor has a resistance of 40 Ω, and the capacitor has a capacitance of 132.6 µF. What is the total current flow through the circuit? What is the impedance of the circuit?What is the power factor of the circuit? How many degrees out of phase are the current and voltage?
Determine the following for the circuit below: (a) The impedance and the supply current (b) The voltages across R, Land C (c) The phase difference between the current and supply voltage with the aid of phasor diagram. Draw both the voltage and impedance triangle/diagrams