1. When a load of 1.2 x 10^6 N is placed on a battleship, the ship sinks 3.5 cm in the water. what is the cross-sectional area of the ship at water level? the density of sea water is 1,027 kg/m^3. A= m^2

1. When a load of 1.2 x 10^6 N is placed on a battleship, the ship sinks 3.5 cm in the water. what is the cross-sectional area of the ship at water level? the density of sea water is 1,027 kg/m^3. A= m^2

Name: Solve it correctly please. I will rate accordingly. 1. When a load of
Uploaded: 2024-03-20T06:51:10.000Z
Channel: Bartleby
Description: Solve it correctly please. I will rate accordingly. 1. When a load of 1.2 x 10^6 N is placed on a battleship, the shipsinks 3.5 cm in the water. what is the cross-sectional area of theship at water level? the density of sea water is 1,027 kg/m^3.A= _

College Physics

1st Edition

ISBN:9781938168000

Author:Paul Peter Urone, Roger Hinrichs

Publisher:Paul Peter Urone, Roger Hinrichs

Chapter11: Fluid Statics

Section: Chapter Questions

Problem 15PE: The greatest ocean depths on the Earth are found in the Marianas Trench near the Philippines....

See similar textbooks

Similar questions

Explain why the fluid reaches equal levels on either side of a manometer if both sides are open to the atmosphere, even if the tubes are of different diameters.
Why is it difficult to swim under water in the Great Salt Lake?
What fraction of an iceberg floating in the ocean is above sea level? Assume the density of the iceberg is 917 kg/m3.
The weight of Earths atmosphere exerts an average pressure of 1.01 105 Pa on the ground at sea level. Use the definition of pressure to estimate the Height of Earths atmosphere by approximating Earth as a sphere of radius RE = 6.38 106 m and surface area A = 4RE2.
Oil having a density of 930 kg/m3 floats on water. A rectangular block of wood 4.00 cm high and with a density of 960 kg/m3 floats partly in the oil and partly in the water. The oil completely covers the block. How far below the interface between the two liquids is the bottom of the block?
A container is filled to a depth of 20.0 cm with water. On top of the water floats a 30.0-cm-thick layer of oil with specific gravity 0.700. What is the absolute pressure at the bottom of the container?
What force must be exerted on the master cylinder of a hydraulic lift to support the weight of a 2000-kg car (a large car) resting on the slave cylinder? The master cylinder has a 2.00-cm diameter and the slave has a 24.0-cm diameter.
A container is filled to a depth of 20.0 cm with water. On top of the water floats a 30.0-cm-thick layer of oil with specific gravity 0.700. What is the absolute pressure at the bottom of the container?
What depth of mercury creates a pressure of 1.00 atm?
The greatest ocean depths on the Earth are found in the Marianas Trench near the Philippines. Calculate the pressure due to the ocean at the bottom of this trench, given its depth is 11.0 km and assuming the density of seawater is constant all the way down.
Every few years, winds in Boulder, Colorado, attain sustained speeds of 45.0 m/s (about 100 mi/h) when the jet stream descends during early spring. Approximately what is the force due to the Bernoulli effect on a roof having an area of 220 m2? Typical air density in Boulder is 1.14 kg/m3, and the corresponding atmospheric pressure is 8.89104 N/m2. (Bernoulli's principle as stated in the text assumes laminar flow. Using the principle here produces only an approximate result, because there is significant turbulence.)
How do you convert pressure units like millimeters of mercury, centimeters of water, and inches of mercury into units like newtons per meter squared without resorting to a table of pressure conversion factors?