Mechanical engineering fluid mechanics questions A cylindrical tank with a height of 1.2m and diameter of 0.6m is three quarters A cylindrical tank with a height of 1.2 m and diameter 0.6 m is threequarters filled with water when stationary. If the tank is rotated aboutits vertical axis at 150 r/min, water spills over the side. Calculate:2.Page 5 of 7a. The maximum depth of the vortex depression above the tank bottom.b. The water level if the tank has been brought to rest.c. The volume of water that was spilled.(68 mm, 436 mm, 75.2 litre)A cylindrical container is 1.5 m deep with a diameter of 0.8 m. It rotatesabout its vertical axis at a speed of 120 r/min. The container is openat its top and was completely filled with water before rotation started.3.07:32

Name: Mechanical engineering fluid mechanics questions A cylindrical tank w
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Mechanical engineering fluid mechanics questions A cylindrical tank with a height of 1.2m and diameter of 0.6m is three quarters A cylindrical tank with a height of 1.2 m and diameter 0.6 m is threequarters filled with water when stationary. If the

Answered: Image /qna-images/answer/d9875d3e-c670-4312-9166-d2ccf975f44d.jpg

Answered: 1.2 m and diameter 0.6 m is three…

Engineering

Mechanical Engineering

1.2 m and diameter 0.6 m is three quarters filled with water when stationary. If the tank is rotated about its vertical axis at 150 r/min, water spills over the side. Calculate

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The plunger diameter of a single-acting reciprocating pump is 115 mm and the stroke is 230 mm. The suction pipe is 90 mm in diameter and 4.2 m long. If cavitation takes place at the suction head of 4 m, the barometer stands at 10.3 m of water, and the water level in the sump is 3 m below the pump cylinder axis.1. Find the maximum allowable speed to operate the pump
The plunger diameter of a single-acting reciprocating pump is 115 mm and the stroke is 230 mm. The suction pipe is 90 mm in diameter and 4.2 m long. If cavitation takes place at the suction head of 4 m, the barometer stands at 10.3 m of water, and the water level in the sump is 3 m below the pump cylinder axis.3.1 Find the maximum allowable speed to operate the pump3.2 What power is expected in overcoming friction at this speed, take ƒ = 0.01
A cylindrical vessel 3m high and 1.50 m diameter is filled with water to a depth of 2.50m. In its side is a 50mm circular orifice C=0.60 placed 30 cm above the bottom of the vessel. If the vessel be rotated about its own axis at 60 rpm and the water is allowed to escape through the orifice for a period of 3 minutes, compute thea. Difference in elevation of the water surface at the center and at the periphery of the tank at this instant.b. Volume of water dischargedc. How deep will the water stand in the vessel if brought to rest?
5) Before transferring the rod into the graduated cylinder, the cylinder tipped and some of the water splashed from the cylinder. The student did not redo the volume. Will the student’s calculated density be higher, lower or the same as the actual density of the rod? Explain.
In an experiment a jet of water of diameter 20 mm is fired vertically upwards at a sprung target thatdeflects the water at an angle of 120° to the horizontal in all directions. If a 500g mass placed on thetarget balances the force of the jet, what is the discharge of the jet in litre/s?
Find the density of a metallic body which flows at the interface mercury of specific gravity 13.6 and water such that 40% of its volume us submerged in Mercury and 60% in water.
Water flows in a channel with uniform curvature ?. The channel has height ℎ = 5 mm and width ? = 190 mm (normal to the drawing plane). The curved part of the channel has a length of ? = 100 mm in the ?-direction. You can assume that the channel height is very small compared to the curvature radius.Neglect effects of gravity. a) Assuming that the pressure is uniform on each of the channel walls, determine the pressure difference between the upper and lower wall that is needed if the required net force on the two walls is 2000 N pointing downward (in the negative ?-direction).Use a sign convention that a positive pressure difference or gradient means the pressure at the higher ?-position is higher. b) Your team agree that, from experience, the average velocity of the fluid is ?= 53 m/s. Assuming that the velocity is uniform across the channel, and neglecting gravitational effects, determine the curvature ?required to generate this force with this flow velocity. Use a sign convention that…
Find the surface tension of the water jet of 38 mm diameter when the inside pressure is 4.5 N/m2 The surface tension in N/m is
If the pressure in a tank of oil (sp gr 0.85) is 376 kN/m2, what is the equivalent head (a) inmeters of oil; (b) in meters of water; (c) in meters of mercury? maintaining the liquid head h at 5.67 ft (d)to what pressure PA be raised in order to double the discharge?
A cylindrical tank ois 6m high and is full of water. An orifice 1m from the top is opened. How far from the bottom of the tank will the jet strike the ground?
An open cylinder tank, D= 1.0m, h=1.5m, contain water at depth 1.0m. If this tank rotate about its central vertical axis. Determine the angular velocity without falling water from its open end
The 6-ft-radius waterwheel in Fig. is being used tolift water with its 1-ft-diameter half-cylinder blades. If thewheel rotates at 10 r/min and rigid-body motion is assumed,what is the water surface angle θ at position A ?