Example Determine the x and y components of each forceacting on the gusset plate of a bridge truss. Show that theresultant force is zero.yEx, EyF2 = 6 kNاولرF = 8 kNنال كل قوة ال مركبن209رجرين ابع النوة امباه XF3 = 4 kNF = 6 kN988000واجمح القوة باتباه ۹اي مرنا888

Answered: Image /qna-images/answer/6219363d-f5b3-47f3-bc79-0fe835e941b4.jpg

1.465 Example Determine thex and y components of each force acting on the gusset plate of a bridge truss. Show that the resultant force is zero. H.W Ex, Ey F2 = 6 kN F = 8 kN تےال كل قوة ال مركبن رعدن ابع القوة انباه X F = 6 kN F = 4 kN 000 واجمع القوة باتباه 3 888

1.465 Example Determine thex and y components of each force acting on the gusset plate of a bridge truss. Show that the resultant force is zero. H.W Ex, Ey F2 = 6 kN F = 8 kN تےال كل قوة ال مركبن رعدن ابع القوة انباه X F = 6 kN F = 4 kN 000 واجمع القوة باتباه 3 888

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. If the shear at a point 1m from the roller support is equal to -217.65765765766kN, determine the value of "w". 2. Determine the deflection at point 3.2m from the hinge support. 3. Determine the deflection at point 1m from the roller support.
The main beam of UB 610 x 229 x 101 kg/m in steel grade S275 supportssecondary beamsof UB 406 x 140 x 39 kg/mon its top flange.The schematic diagram of the floor supported by the beams is presented in Figure 1. b)The slab floor is reinforced concrete 150 mm thickwith 50 mm screed on top of it. The slab floor carriesthe uniform distributed load of 400 kg/m2.Calculate the ULS load on the secondary beam. 4xxx= 4715 1xxx= 1715 50xx= 5015
What is the force carried by member DE? Select one: a. 402 kN b. 240 kN c. 204 kN d. 420 kN
The 300-lb force is to be resolved into components along lines a-a’ and b-b’. 1. Determine the angle α knowing that the component along line a-a’ is 240-lb. 2. What is the corresponding value of force along line b-b’?
Determine the magnitude of the 15 points force in member CD using method of section * (O 35.3KN Tension O none of the above (O 15.02KN Tension () 27.7 KN Compression (O 13.83 KN Tension O 16.2 KN Compression
Find the deformation of the bar in the figureE= 200gpa
A short length of a rolled-steel column supports a rigid plate on which two loads P and Q are applied as shown. The strains at two points Aand B on the center lines of the outer faces of the flanges have been measured and found to be εA=–400 * 10-6 in./in. εB= –300 * 10-6 in./in.Knowing that E= 29 * 106 psi, determine the magnitude of each load.
What is the internal force in member AD? A. 750 N , T B. 450 N , T C. 750 N , C D. 450 N , C SHOW SOLUTIONS
The T section shown is formed by joining two rectangular pieces of wood together. The beam is subjected to a maximum shearing force of 60 kN. All dimensions are in mm . A.) Which of the following gives the moment inertia in x 10^6mm^4 at the neutral axis? Choices: 8.56,14.26,10.57,21.52 B.) Which of the following gives the shearing stress at the neautral axis? Choices: 3.21,4.64,3.95,4.28 C.) Which of the following gives tge shearing stress in MPa at the junctiin between two pieces of wood? Choices: 31.78,21.42,28.32,16.52
The initial compressive force of a steel column can be determined by using the Euler's Critical Load Formula. The x-axis has an unbraced length of L meters which is fixed at the top and bottom supports to prevent sidesway. The y-axis has an unbraced length of L/2 meters due to the bracing at mid-height. The properties of the column are the following A=8,338mm2 , Ix=177,283,158mm4 , Iy=23,354,047mm4 ,Fy=345MPa. Calculate the minimum length, L of the column in millimeters without exceeding the proportionality limit, fs=300MPa. Express your answer in 2 decimal places.
an 8 m long steel is pinned at the top and fixed at the bottom. the column is provided with lateral support 3m from the top in the weak direction. the properties of the column section are as follows: ix = 178.1x10^6 mm^4 ly = 18.8x10^6 mm^4 a = 8129 mm^2 fy = 400 mpa a. what is the critical effective slenderness ratio? %3d %3d b. what is the buckling stress of the column? c. calculate the critical load pc in kn
Problem 11.075 - Determine the vertical deflection of point C caused by the load P Each member of the truss shown is made of steel and has a cross-sectional area of 5 in2. Using E = 29 × 106 psi, determine the vertical deflection of point C caused by the 10-kip load P. (Round the final answer to three decimal places.) The vertical deflection of point C is in. ↓.