Steel floor beam -Steel girder (A = 25,600 mm?) Problem 2. The floor system of a gymnasium consists of a 130- (A = 9,100 mm2) A D Steel B mm-thick concrete slab resting on four steel beams (A = 9,100 column mm2) that, in turn, are supported by two steel girders (A = 25,600 mm2), as shown in Figure. Determine the dead loads 130 mm 10 m concrete acting on beam BF and girder AD. slab E- F G -3 at 5 m 15 m

Steel floor beam -Steel girder (A = 25,600 mm?) Problem 2. The floor system of a gymnasium consists of a 130- (A = 9,100 mm2) A D Steel B mm-thick concrete slab resting on four steel beams (A = 9,100 column mm2) that, in turn, are supported by two steel girders (A = 25,600 mm2), as shown in Figure. Determine the dead loads 130 mm 10 m concrete acting on beam BF and girder AD. slab E- F G -3 at 5 m 15 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The partial plan layout for the framed structure of a multistory building is shown below. The vertical structure consists of columns and the horizontal floor structure of a one-way deck and beam system. The uniformly ultimate (factored) distributed load for the one-way-spanning deck is equal to 0.14 kip/ft2. Ignore the own weights of beams and walls. L1 = 22 ft, L2 = 22 ft, L3 = 32 ft. Compute the load on column 1. Compute the value of distributed load on beam A. Compute the value of concentrated loads on beam C. Draw the shear and bending moment diagrams for beam C (with values) – Assume beam C as simply supported.
A reinforced concrete column 500mm square in section is reinforced with four steel bars of 25mm diameter, one in each corner. The column is to carry load of 1000kN. Calculate the stresses in the concrete and steel bars. E steel=219X109N/m2 and E concrete =14X109N/m2
The interior wall of a building is made from 2 x 4 wood studs, plastered on two sides. If the wall is 12 ft high, determine the load in lb/ft of length of wall that it exerts on the floor. Check the minimum design dead load table for the unit weight.
A rectangular beam has the following properties: b = 300 mm, d = 350 mm, tension bars As = 4-28mmØ,compression bars As’ = 2-28 mmØ, d’ = 60 mm. Fc’ = 30 MPa and fy = 345 MPa Determine the design strength of the beam.a. 233.155 kN.m. c. 636.511 kN.m.b. 332.511 kN.m. d. 755.321 kN.m. Calculate the ultimate axial load capacity of a round spiral column having a diameter of 400 mm reinforced with 6-20 mm Ø bars having fc’ = 24 MPa and fy = 276 MPa a. 1941.401 kN c. 1841.321 kNb. 9141.401 kN d. 8141.321 kN Please answer asap.
Calculate the total equivalent uniform load in KN/m on Beam AB, if the total floor load is 11.56KPa. Use a=3.7m, b=5.8m . Express your answer in 2 decimal places.
A rectangular beam has the following properties: b = 300 mm, d = 350 mm, tension bars As = 4-28mmØ, compression bars As’ = 2-28 mmØ, d’ = 60 mm. Determine the design strength of the beam.a. 233.155 kN.m. c. 636.511 kN.m.b. 332.511 kN.m. d. 755.321 kN.m. Calculate the ultimate axial load capacity of a round spiral column having a diameter of 400 mm reinforced with 6-20 mm Ø bars having fc’ = 24 MPa and fy = 276 MPa. a. 1941.401 kN c. 1841.321 kNb. 9141.401 kN d. 8141.321 kN
Calculate the governing load combination for a secondary beam with effective width = 2.0 m Dead load Weight of slab = 3.0 kPa Ceiling services = 1.0 kPa Self-weight of beam = 1.0kN/m Imposed load - 0.2 kPa
A reinforced concrete beam as shown in the figure below has a flange width of350mm, flange thickness of 120mm, and an effective depth of 600 mm. It is reinforced with 3-32 mm ∅ at the bottom. If fc’ = 28MPa, and fy = 275 MPa, determine the following:a. Balance steel ratiob. Depth of compression block.c. Moment capacity of the beam.
The uniformly distributed live load on the floor plan in Figure P2.4 is 60 lb/ft2 . Establish the loading for members (a) floor beam B1, (b) floor beam B2, (c) girder G1, and (d) girder G2. Consider the live load reduction if permitted by the ASCE standard.
A hospital located in central Illinois has a flat room. Determine the snow load in kN/m^2 that is required to design the roof.
A floor slab 100 mm thick is cast monolithically with beams 300 mm wide 500 mm deep spaced 1.5 m on centers, on simple supports over a span of 6.0 m. The floor supports a superimposed service dead load of 1.77 kPa and service live load of 4.8 kPa. Using f’c= 21 MPa, long bar fy = 415 MPa, calculate Using a T-beam geometry formed from monolithic construction, determine the effective flange width of a typical interior beam in mm.
A floor slab 100 mm thick is cast monollthically with beams 250 mm wide 450 mm deepspaced 1.2 m on centers, on simple supports over a span of 5.0 m. The floor supports asuperimposed service dead load of 1.0 kPa and service live load of 2.1 kPa. Using f.=21MPa, long bar f, = 415 MPa, calculate the following:Factored uniform load on a typical interior beam in kN/m using load factors of 1.2for dead load and 1.6 for live load.A. 8.928B. 11.448C. 11.028D. 9.960Effective flange width of a typical interior beam in mm.A. 1,500B. 1.850C. 1.200D. 1.466Required amount of 16-mm-flexure bars for a typical interior beam in positivebending. Use 10-mm-dia. stirrupsA. 512 mm2B. 246 mm2C. 331 mm2D. 427 mm2