1.7 kN/m 3m Mui 1m 20KN

Q: An excavation is made with a vertical face in a clay soil which has C = 50 KN/m², y = 18 KN/m³. The…

A: Given- cohesion of the soil C=50 KN/m2unit weight of soil γ=18 kN/m3Stability no. Sn=0.261Angle of…

Q: Re-design the reinforcement and check the deflection for the beam 5B2 shown in DWG-01 of Chapter 1…

A: Solution: Given: Beam over all depth, h = 750 mm Beam breadth, b = 400 mm Slab thickness, hf = 160…

Q: Determine the Reactions of the structure. Draw the Shear and Moment diagram Member CDE only. Let P…

A:

Q: B 6m 8) 20KN By using an appropriate method, i) 6m 20kN/m 30KN Figure 1 6m M H 20KN 6m 'LL G Figure…

A: For given truss stability and determinacy can be evaluated externally as well as internally.…

Q: Use the virtual work method to determine the slope and deflection at point D of the beam shown. -15…

A: Given data  E = 10,000 ksi  I = 2500 in4  Find slope and deflection at point D using virtual load…

Q: A secondary clarifier handles a total flow of 9600 m³/d from the aeration tank of a conventional…

A: Given: Total flow = 9600 m3/d, Solids concentration = 3000 mg/l, Design solid flux = 3.2 kg/m2.h

Q: A section of highway has a superelevation of 0.05 and a curve with a radius of 300 ft. What is the…

A: since  it is the problem of design  so initially i have to assume the data here for f that is…

Q: A tube-well of 20 cm of diameter fully penetrate a horizontal, homogeneous and isotropic confined…

A:

Q: As we explained in Chapter 10, viscosity is a measure of how easily a fluid flows. For example,…

A: Given:- μ = c1 10c2 1(T−c3 )whereμ = viscosity (N/s.m2 )T = temperature (K)c1=2.414×10-5 (N/s.m2 )…

Q: excavation of a certain foundation pit, draining water causes upward seepage. The water head…

A:

Q: The water flow of 35,000 Liters/min was developed into a booster station with a pump installed rated…

A: Discharge = 35000 lit/sec P2 = 4.18 bars = 8730.127 lb/ft2 P1 = 220mm Hg = 612.589 lb/ft2 A1 = 0.785…

Q: For a soil sample, the following set of experimental data has been obtained: Liquid Limit (LL) = 34…

A: Given:Liquid Limit (LL)=34Plastic limit (PL)=6Now,Plasticity Index PI=LL-PLPI=34-6PI=28

Q: Q- To provide safety against piping failure, with a factor of safety of 5, what should be the…

A: Given data- FOS=5Specific gravity G=2.5n=0.35To Find-maximum exist gradient.

Q: Can you please explain or elaborate the step 3 in sentences

A: I explain step 3 in sentences for your understanding. I use some written content also.

Q: Figure 3: Member BCDE only a. Determine the Reactions of the following structures. b. Draw the…

A: Given P = 19 Required  Support reactions  Shear force and bending moment diagram for member BCDE

Q: A brass cube, 6 in on side weighs 67 lb, we want to hold this cube in equilibrium under water by…

A:

Q: The average velocity of the fluid in the

A: Given. Fluid flowing staedily in a circular pipe of radius R.  Velocity distribution along the…

Q: Determine the reactions. A 3 39 kN/m 3 m 2 m 16 KN 2 m B 18 kN/m 3 m

A:

Q: A rectangular gate having a width of 4 ft is located in the sloping side of a tank as shown in the…

A:

Q: Discuss the procedure of horizontal taping measuring on sloping ground?

A: The use of a surveyor's tape to measure the horizontal distance between two points is known as…

Q: 0⁰) iv) Calculate the total vertical displacement at joint D if the all member is subjected to an…

A:

Q: The cohesion (c), angle of internal friction () and unit weight (y) of a soil are 15 kPa. 20° and…

A:

Q: What are the amounts of cut and fill needed between station 90+25 with fill area of 445 sq.ft and…

A:

Q: 30 mm y = C 30 mm b An aluminum strut has a cross section referred to as a deep hat. Locate the…

A: Given data  a = 70 mm  b = 115 mm  Thickness = 12mm

Q: If a small concrete cube is submerged deep in still water in such a way that the pressure exerted on…

A: Given- Pressure exerted on all faces of cube=pIt is needed to find the value of maximum shear stress…

Q: how can we clasify clay is it organic or inorganic compound?

A: The soil above A-line in the plasticity chart is called clay with particle size less than 2 micron.…

Q: 5) A line measured with a 40.0 m long steel tape was determined to be 7500.0 m when the average…

A:

Q: A force P=45 KN is applied to a short section of a steel member of specification W 150 x 24.…

A:

Q: The construction company outside is raising a 200 foot steel beam using a crane. At the start, it's…

A: Given values: Consider beam AB, L = 200 ft Increase in angle between beam and ground , dθdt=0.8…

Q: 4. Determine the rectangular representation of the resultant force and direction angle of the figure…

A:

Q: The cyclindrical tank with hemispherical ends shown in the figure below contains a volatile liquid…

A: Reference : Fluid mechanics, Pressure analysis for Volatile liquid. We know that , Gage pressure is…

Q: I | Environmental Engineering A water treatment plant has a flow rate of 0.6 m³/s. The settling…

A: Given- flow rate Q=0.6 m3/sdimensions-L=20 mD=3 mB=6 mSettling velocity Vs=0.004 m/s% of particles…

Q: B 80) 6m 20KN 6m 20kN/m D 30KN Figure 1 6m M H 20KN 6m G 8m Figure 1 above shows a truss structure,…

A: For a given truss External SI = R - r R = Number of unknown reactions = 3 r = number of equilibrium…

Q: The concrete (specific weight = 150 lb/ft³) seawall of the figure below has a curved surface and…

A: There will be horizontal force and vertical force on the curved surface.  The forces and the…

Q: Can you please explain the process of step by step in a paragraph?

A: Step 1: Find the reactions at the support using equilibrium conditions. Step 2: Shear force and MEI…

Q: How is the driver’s psychology or perception considered in geometric design?

A: Driver's perception factor is consider in the following parameters of geometric design: (1) Sight…

Q: ugh pressure taps de of the device.

A: Given, U-tube manometer The liquid in the pipe is water Pipe Horizontal, diameter not varying…

Q: The effective stress

A: Given data, Vertical pressure,P= 50 kN/m3 pore water pressure immediately on increasingthe vertical…

Q: 22= 2 R₁-R3 - 50 R3=2R₁-2₂ + 3C

A: The sides of triangle are R1, R2 , and R3. As per the given question, R1-R2-2R3 = -40-2R1+R2+R3 =…

Q: Example 10.1 - A simply supported girder has a span of 5.5m with a factored concentrated load of 250…

A:

Q: A horizontal nozzle of 30 mm diameter discharges a steady jet of water into the atmosphere at a rate…

A:

Q: 4. For the truss shown, determine the forces in members AB, BG, ED and GF 6 kN 2.4m B 24m C 24 m D…

A:

Q: A vertical plane area having the shape shown in the figure below is immersed in an oil bath…

A:

Q: The thickness of the laminar boundary layer on a flat plate at a point A is 2 cm and at a point B,…

A: Given data: The thickness of the laminar boundary layer on a flat plate at a point A is 2 cm. At a…

Q: A person by the name of Huebscher developed a relationship between theequivalent size of round ducts…

A: Given data:- Thus according to Huebscher, a relationship was created between the equivalent…

Q: In your own words, explain the difference between absolute humidity and relative humidity.

A: There are three different types of water on the planet:- solid (ice), fluid (water), and gaseous…

Q: Can you please explain and elaborate STEP 4 in sentences

A: Explanation for step 4: Release the moment at A and support B is allowed to rotate. Let the…

Q: Design a rectangular tied column for flexure in a reinforced concrete frame is subjected to the…

A: Answer Let us first calculate the Maximum axial load Pu and Maximum Moment Mu 1)Pu = 1.2*PD+1.6*PL…

Q: n anallactic tacheometer in use on a remote survey was damaged und it was decided to use a glass…

A:

Q: A 3m 30 kN 3 m 5 kN/m 6m B

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…