H.W.1 /The cantilever beam in Figure below has a rectangular cross section with dimension(20 mm(width) x40 mm (height)).(a). Find the maximum bending stress (oms) in the beam.(b) Find the maximum bending stress (amar) in point B and C in the beam (c)Sketch thebending stress distribution over the cross scction on which the maximum bending stressoccurs.Aв10 Ib/ftC20 ft60 ft

Answered: Image /qna-images/answer/81ef3619-efb4-4284-9594-bb8e9029fe77.jpg

1.W.1/The cantilever beam in Figure below has a rectangular cross section with dimension 20 mm(width) x40 mm (height)).(a). Find the maximum bending stress (Gman) in the beam. b) Find the maximum bending stress (ama) in point B and Cin the beam (c)Sketch the ending stress distribution over the cross section on which the maximum bending stress ccurs. A в 10 Ib/ft 20 ft 60 ft

1.W.1/The cantilever beam in Figure below has a rectangular cross section with dimension 20 mm(width) x40 mm (height)).(a). Find the maximum bending stress (Gman) in the beam. b) Find the maximum bending stress (ama) in point B and Cin the beam (c)Sketch the ending stress distribution over the cross section on which the maximum bending stress ccurs. A в 10 Ib/ft 20 ft 60 ft

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

If Mz = 210 kip-ft, find the magnitude of the bending stress at a point H. For the beam cross section, assume a = 7 in. b = 10 in. d = 28 in. r = 3.5 in. The centroid of the cross section is located 12.88 in. below the uppermost surface of the beam. The moment of inertia about the z axis is 15990 in.4.
If M, = 285 kip-ft, find the magnitude of the bending stress at a point H For the beam cross section, assume a = 9 in. b= 12 in. d= 31 in r= 45 in. The centroid of the cross section is located 14.16 in. below the uppermost surface of the beam. The moment of inertia about the z axis is 26227 in 4
The uniform sign has a weight of 1500 lb and is supported by the pipe AB, which has an inner radius of 2.75 in. and an outer radius of 3.00 in. If the face of the sign is subjected to a uniform wind pressure of p = 150 lb>ft2, determine the state of stress at points C and D. Show the results on a differential volume element located at each of these points. Neglect the thickness of the sign, and assume that it is supported along the outside edge of the pipe.
If d = 450 mm, determine the absolute maximum bending stress in the overhang beam.
Since the beam M in the figure is under the effect of simple bending moment, calculate the bending stress and shear stress values at the A, B and C points. h = 400mm b = 140mm and M = 150KNm
1.) Draw the internal stress and strain diagram of beam considering that the depth of the stress block is greater than the thickness of the flange. f’c =30 MPa, fy=400 MPa and is subjected to a positive bending Mu=140KN-m.
If σsafety=140MPa (safety stress) in the beam whose loading condition and cross-section are visible, find the maximum value of the P force, Based on the assumption of Maximum shear stress (Tresca) and deformation energy (Von Mises) theorems. Draw the shear stress diagram for the force P found.
The moment acting on the cross section of the unequal-leg angle has a magnitude of 15 kN-m and is oriented as shown in the figure. All stresses are positive if tensile and negative if compressive. Assume a = 245 mm, b = 175 mm and t = 24 mm.Determine(a) the bending stress at point H.(b) the bending stress at point K.(c) the maximum tension and the maximum compression bending stresses in the cross section.(d) the orientation β of the neutral axis relative to the +z axis. (a) σH= MPa (b) σK= MPa (c) σmaxT= MPa σmaxC= MPa (d) β= °
From the given simply supported beam below, determine the following: d. The moment of inertia with respect to the neutral axis. e. The maximum flexural stress and shear stress of the beam. f. The bending stress at point B and C. g. The shear stress at the mid-point of the beam.
A couple M of moment 8 kN·m acting in a vertical plane is applied to a W200 * 19.3 rolled-steel beam as shown. Determine (a) the angle that the neutral axis forms with the horizontal plane, (b) the maxi-mum stress in the beam
Since the bending safety stress σem = 10 MPa, shear safety stress Tem = 600 kPa of the rectangular section beam given the loading status in the figure and width b = 150 mm, how much should the height h of the beam section be at least so that the stresses that will occur in the beam do not exceed the safety stress values. .
The T-shaped beam shown above is supporting a concentrated load P at its free end. The beam has an allowable bending stress of ?????? = 250 MPa and an allowable shear stress of ?????? = 100 MPa. a) Determine the distance to the neutral axis (?̅), second moment of area (?), and the section modulus (?) of the cross-section.b) Draw the shear force diagram (SFD) and bending moment diagram (BMD) of the beam. On your diagrams, express the values of shear and moment in terms of the applied load P.c) Determine the maximum value of P such that bending failure will not occur.d) Determine the maximum value of P such that shear failure will not occur.e) Based on your answers to (c) and (d), what is the maximum load P that can be applied to the beam? Is this beam bending or shear governed?