10) The secondary side of a Delta-Wye transformer is shown below, with the line-to-line 208 V connections labeled. a) If a 3000 W three-phase load (PF=1) is connected to the secondary side, what is the current? b) What is the voltage for each of the one-phase connections (A-N, B-N, and C-N)? ele Grounded 208 208 A B 208 - N C

10) The secondary side of a Delta-Wye transformer is shown below, with the line-to-line 208 V connections labeled. a) If a 3000 W three-phase load (PF=1) is connected to the secondary side, what is the current? b) What is the voltage for each of the one-phase connections (A-N, B-N, and C-N)? ele Grounded 208 208 A B 208 - N C

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.45P: Two balanced Y-connected loads, one drawing 10 kW at 0.8 power factor lagging and the other IS kW at...

See similar textbooks

Similar questions

An infinite bus, which is a constant voltage source, is connected to the primary of the three-winding transformer of Problem 3.53. A 7.5-MVA,13.2-kV synchronous motor with a sub transient reactance of 0.2 per unit is connected to the transformer secondary. A5-MW,2.3-kV three-phase resistive load is connected to the tertiary Choosing a base of 66 kV and 15 MVA in the primary, draw the impedance diagram of the system showing per-unit impedances. Neglect transformer exciting current, phase shifts, and all resistances except the resistive load.
Three single-phase transformers, each rated 10MVA,66.4/12.5kV,60Hz, with an equivalent series reactance of 0.1 per unit divided equally between primary and secondary, are connected in a three-phase bank. The high-voltage windings are V-connected and their terminals are directly connected to a 115-kV three-phase bus. The secondary terminals are all shorted together. Find the currents entering the high-voltage terminals and leaving the low-voltage terminals if the low-voltage windings are (a) Y-connected and (b) - connected.
Consider a three-phase Y-connected source feeding a balanced- load. The phasor sum of the line currents as well as the neutral current are always zero. (a) True (b) False
(a) An ideal single-phase two-winding transformer with turns ratio at=N1/N2 is connected with a series impedance Z2 across winding 2. If one wants to replace Z2, with a series impedance Z1 across winding 1 and keep the terminal behavior of the two circuits to be identical, find Z1 in terms of Z2. (b) Would the above result be true if instead of a series impedance there is a shunt impedance? (c) Can one refer a ladder network on the secondary (2) side to the primary (1) side simply by multiplying every impedance byat2 ?
there is a three-phase transformer that supplies 12 kW to a neighborhood supermarket, the same is in the standards and is considered a balanced three-phase load with inductive power factor of 0.8. If the supermarket at the supply input is star connected, fed with four conductors and operating at a phase-neutral voltage equal to 200 V. What is the line current with this load?
9. A 3-phase transformer rated at 1,000 kVA, 11/3.3 kV has its primary windings wye-connected and its secondary windings delta-connected. The actual resistances per phase of these windings are: r1 = 0.375 Ω, r2 = 0.095 Ω; and the leakage reactances per phase are: x1 = 9.5 Ω, x2 = 2 Ω. Calculate the voltage at the normal frequency which must be applied to primary terminals in order to obtain full-load current in the windings when the secondary terminals are short-circuited. Also, calculate the power input under these conditions.
in the circuit of the figure, we know: 1) the impedance of the A-B line: (26.6+j107) ohm 2) C-D line impedance: (4.5+j17.5) ohm 3) the nominal values of transformer 1: single-phase transformers' bank (7.97 KV in Y, 230 kV in delta, 50 MVA, x= 8%, r= 3%) 4) the nominal values of the transformer 2: three-phase transformer (220 KV in Y, 88 kV in delta, 40 MVA, x= 8%, r= 3%) 5) the voltage (80kV) and power of the load (30 MVA, cos phi 0.8 inductive) determine the voltage at the primary of transformer 1
There single-phase transformers are 3 transformers (Each of them is to be connected Delta-Delta) is rated at 50kVA, 2200/400 V , Zeq = 1.4 + j1.8 ohms (Ref. the high-voltage side of the transformer). The high voltage side of the transformer receives 2200 V by the transmission line (impedance of transmission line is 0.15+j0.80 ohms). The Low voltage side of the transformer disburses load by the transmission line (impedance of transmission line is 0.001+j0.003 ohms). Determine Load Voltage when the transformer works at rated by PF=0.85 lagging
Consider a portion of a power system with two generators (G1 and G2) in parallel connectedto a step-up transformer (T) which links them with a 240 kV transmission line (TL). The ratingsof the components are given as under:G1: 100 MVA, X=12%G2: 5 MVA, X=8%T: 15 MVA, X=6%TL: 4+j6 Ω, 230 kVWhere the percent reactances are computed on the basis of individual component ratings.Express the reactances and the impedances with 15 MVA as the base value.
II.) The number of turns on the primary and secondary windings of a single-phase transformer are 350 and 38 respectively. If the primary winding is connected to a 2.2 kV, 50-Hz supply, determine (a) the secondary voltage on no-load, (b) the primary current when the secondary current is 200A at 0.8 p.f. lagging, if the no-load current is 5 A at 0.2 p.f. lagging, (c) the power factor of the primary current. [239 V; 25-65 A; 0.715 lag]
A Wye-Delta transformer is connected t0 66 kV input three-phase transmission line. Each transformer is rated at 1000 kVA and has step-down ratio of 8.1_ The bank supplies balance load having powel factor of hag with load current of 70 Assume idea transformer; determine_ The primary line and phase voltages The secondary line and phase voltages The secondary line and phase currents The apparent and active power at the load Total kVA capacity of the transformer
A star connected load with real impedance ZL= 1-j1 Ohm per phase is connected to the secondary of a three-phase Ynyn0 connected transformer. The equivalent impedance per reduced phase of the transformer to the primary is Zeq1= 1+j5 Ohm. The nominal primary voltage is V1Ln= 5920 V and the conversion ratio is a= 10. what is the amplitude of the actual voltage falling on one phase of the specified load? (simplified equivalent circuit will be used).