10. A fluid flows through a horizontal 0.1-in.-diameter pipe. When the Reynolds number is 1500, the head loss over a 20-ft length of the pipe is 6.4 ft. Determine the fluid velocity. 11. A viscous fluid flows in a 0.10-m-diameter pipe such that its velocity measured 0.012 m away from the pipe wall is 0.8 m/s. If the flow is laminar, determine the centerline velocity and the flowrate.

10. A fluid flows through a horizontal 0.1-in.-diameter pipe. When the Reynolds number is 1500, the head loss over a 20-ft length of the pipe is 6.4 ft. Determine the fluid velocity. 11. A viscous fluid flows in a 0.10-m-diameter pipe such that its velocity measured 0.012 m away from the pipe wall is 0.8 m/s. If the flow is laminar, determine the centerline velocity and the flowrate.

Name: 10. A fluid flows through a horizontal 0.1-in.-diameter pipe.When the
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: 10. A fluid flows through a horizontal 0.1-in.-diameter pipe.When the Reynolds number is 1500, the head loss over a 20-ftlength of the pipe is 6.4 ft. Determine the fluid velocity.11. A viscous fluid flows in a 0.10-m-diameter pipe such that itsvelo

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Flow In Closed Conduits 2. Water at 25C flows through a 200-mm diameter new cast iron pipe at a velocity of 2 m/s if the pipe is 720 m long, determine the head lost due to friction using Darcy – Weisbach formula. Answer: _______________________________
1 - If the pipeline is now specified to be of Schedule 40 with a nominal diameter of 6 in., and the available pressure at the pump exit is P2 = 132.7 psig, what flow rate Q (gpm) can be expected? Answer the following additional questions: 2 -If the combination of pump and motor is 80% efficient, how much electrical power (kW) is needed to drive the pump? 3 -, in order to avoid vapour lock, the pressure in the pipeline must always be above the vapor pressure of the crude oil, what is the maximum permissible elevation of point 3 relative to point 4? 4 -If the flow in the pipeline were at the upper limit of being laminar, what pump exit pressure would then be needed? (Answer this part without using the friction factor plot.
10.) A horizontal pipe gradually reduces from 300 mm diameter section to 100 mm diameter section. The pressure at the 300 mm section is 100 kPa and at the 100 mm section is 70 kPa. If the flow rate is 15 liters/sec of water, compute the head lost between the two sections. Answer: 2.872m Subject: Fluid Mechanic Lesson: Relative Equilibrium of Liquids Fundamentals of Fluid Flow
Two pipes with C1= 120, connected in series, discharge 4.75 cfs with a loss of head of 27 ft. Each pipe has a length of 1000 ft.If one pipe has a diameter of 18 inches, determine the diameter of the other pipe. Neglect minor losses.
When glycerin (25°C or 77°F) flows through a 30 m (100 ft) length of 75 mm (3 in.) pipe,the head loss is 36 m (120 ft). Calculate the flowrate
Water flows through the piping junction, entering section 1 at 20 US gallons/min (1 US gal = 3.78 L). The average velocity at section 2 is 2.5 m/s. A portion of the flow is diverted through the shower head, which contains 100 holes of 1-mm diameter. Assuming uniform shower flow, estimate the exit velocity from each hole of the the shower head. Answer should be in m/s.
Water at 38°C flows from A to B through 244 m of average 300-mm-I.D. cast iron pipe (e = 0.00061 m).Point B is 9.1 m above A, and the pressure at B must be maintained at 138 kPa. If 0.222 m3/s is to flowthrough the pipe, what must be the pressure at A? Ans. 314 kPa (show the complete solution with diagram) [Note: Indicate the formula used in determining the friction factor. (Colebrook Equation, Haaland Equation, andor Swamee Jain Equation). If not given, Use properties of fluid based ontemperature available ontheinternet.E.g. (density, viscosity). Apply roughness of pipe values from https://www.pipeflow.com/pipe-pressure-drop-calculations/pipe-roughness]
A 12′′ pipe line carries oil of specific gravity 0.811 at a velocity of 80.0 ft/sec. At points A and B, measurements of pressure and elevation were 52.6 psi and 100.0 ft and 42.0 psi and 110.0 ft,respectively. For steady flow, find the lost head between A and B. indicate the free body diagram
Water flows at a rate of 500 gal/min through a 400-ft-long line. The first and last 100 ft of the line are 6-in-diameter cast iron pipes, while the middle 200 ft consists of two 4.24-in-diameter cast iron pipes. Find: a. Provide a diagram b. the average velocity in each section of pipe, c. the pressure drop in each length of pipe, and d. the total pressure drop.
1) 2) Determine the Reynolds number in the pipe system and the significance of this Information? 3) Using Bernoulli’s equation, find the water pressure at point C? 4) Determine the head losses accumulated by the fluid when flowing in the pipeline? 5) Calculate the energy that the fluid will lose after passing through the turbine by applying theenergy equation? 6)If the used turbine converts only two-thirds of the energy that the fluid will lose after passing through the turbine, what is the efficiency of this turbine? 7) Identify the most common water turbines and the limitations that exist within these differenttypes? 8) Although hydraulic turbines considered one of the most efficient power plants, theirecological impact is a big concern. Discuss this issue and suggest remedies for such problems by writing 100 words at least?
How many gal/hr of water at 68 deg F can be delivered through a 1320-ft length of smooth 6.00 in i.d. pipe under a pressure difference of 0.25 psi. Assume that the pipe is “hydraulically smooth”
Assumptions of a discharge and a friction head loss through the series of pipe and the parallel of pipe are different. For pipes in series, the total discharge equals to the individual discharge in each pipe. For pipes in parallel, the total friction head loss equals to the individual friction head loss in each pipe. True or false