10. The rigid bars shown are separated by a roller and hinged at A and D. Bar AC is supported by a steel rod at B. Calculate the vertical movement of the roller at C. E= 200 GPa A = 300 mm² L= 3 m | 50 kN 2 m 2 m A B D 3 m 1.5 m

10. The rigid bars shown are separated by a roller and hinged at A and D. Bar AC is supported by a steel rod at B. Calculate the vertical movement of the roller at C. E= 200 GPa A = 300 mm² L= 3 m | 50 kN 2 m 2 m A B D 3 m 1.5 m

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.9.30P

See similar textbooks

Related questions

Q: Completely determine the resultant of the forces shown in the figure. Option: R= 957lb down to the…

Q: 2. A helical gear has a normal diametral pitch of 12. a nor- mal pressure angle of 20°, 48 teeth, a…

Q: Calculate the Reynolds number, Re for water flow in a circular pipe. The diameter of the pipe is 50…

A: Reynold's Number is defined as the ratio of Inertia force to the viscous force in a flowing fluid.…

Q: The concrete gravity dam is held in place by its own weight. If the density of concrete is 2.5 Mg/m,…

Q: Calculate the moment of inertia of the shaded area about the x-axis. A

A: Triangle: Base, b= 45+45= 90 mm Height, h= 84 mm Semicircle: Radius, r= 28 mm

Q: process is

A: Given, Following are the process given for a TD process:Where, During a non-flow TD process (1-2)…

Q: If the viscosity of water at 70 °C is 0.0042 poise and its specific gravity is 0.97, determine its…

Q: A pelton wheel working under a head of 50 meters, develops 80 kW at 230 rpm. Calculate the diameter…

A: Given Head, h = 50 m Power, P = 80 kW Speed, N = 230 rpm Find Diameter of the jet, d

Q: Which of the following heat treatment

A: Given; Following are the heat treatment process used for surface hardening of steels: Where,Heat…

Q: The strain components εx, εy, and γxy are given for a point in a body subjected to plane strain.…

Q: i need the answer quickly

A: For quarter circle, r= 150 mm X1 = 4r/3π =4×150/3π= 63.662 mm Y1 = 4r/3π =4×150/3π= 63.662 mm…

Q: 10) A cast steel pulley attached to a 50mm shaft is transmitting 30kW @ 200rpm, and is keyed by a…

A: Given:d=50 mmP=30 KWN=200 rpml=75 mmSx=400 MPa

Q: 330 feet (100m) of pressure head to a flow of water. The velocities in the suction and discharge…

A: Given, h2 - h1 =100 m, v1 = 2 m/sec v2 = 5 m/sec P = 50 kW

Q: Summarise and discuss the concepts and applications of Design for Additive Manufacturing (DfAM)

A: Given question: Summarize and discuss the concepts and applications of Design for Additive…

Q: Water is pumped at a rate 50o litres per minute through a 1 km horizontal, circular pipe of diameter…

A: Given:Q=500 l/minL=1 km =1000 md=20 cm =0.2 mf=0.05

Q: A STAR WHEEL ADJUSTER RETURN SPRINGS ANCHOR PLATE E ANCHOR PIN PLATE SPRING SPRING STAR WHEEL…

A: Backing plate - C Shoe - D Wheel cylinder - A

Q: Calculate the velocity v of the 50-lb cylinder after the 20-lb cylinder has dropped 6 ft. 41 lb 50…

A: m1= 50 lbm2= 41 lbm3= 20 lb20 lb cylinder has dropped 2 ft.Hence, y1= -6 ft, y2= 6 ft, y3= 6 ft To…

Q: hat differences between ADF and VOR navigation?

A: 1. ADF is short for Automatic Direction Finder. And VOR stands for VHF Omni-directional Range. 2.…

Q: value of h will be

A: Given: Figure shows a schematic diagram of simple watt governor mechanismwith spindle o1o2 rotating…

Q: The following data was collected in a road project: • Free haul distance = 50 meters Cost of borrow=…

Q: If a Carnot cycle operates at temperature limits of 283 K and 319 K, determine the ratio of the work…

Q: Discuss the reason why during WWII, tailwheel and low wing configuration in aircraft is ideal.

A: given; Discuss the reason why during WWII, tailwheel and low wing configuration in aircraft is…

Q: is necessary to start the system of blocks moving to the right? The coefficient of friction is 0.10…

Q: A centrifugal pump of the following characteristics is used to pump the water between 2 reservoirs,…

A: The Power required by the pump to deliver the water to the required can be calculated by the formula…

Q: Determine the equivalent state of stress on an element at the same point which represents (a) the…

A: According to Bartleby guidelines, we are allowed to solve only the first 3 sub-part of a single…

Q: If the daily kw-hr energy by household using solar energy within 6 hrs peak sunlight in a day is 412…

A: Daily solar energy used by household, E = 412 kw hr No of hours, n = 6 hrs

Q: An ideal regenerative cycle is executed with 56700 kg/hr of steam initially at 13.44 MPa and 594 °C.…

Q: Question 5 A fountain consists of a horizontal inlet pipe with a cross-sectional area, At, which…

A: The free body diagram of the block and nozzle is given below,

Q: Using affinity laws, develop a pump curve and BHP curve for a 1 ½" AB pump for a 6" impeller. Use a…

Q: A piston/cylinder arrangement contains 2 kg of ammonia at a temperature 132.45 ℃ and a pressure 5…

Q: 4 Considor the sys bolow X (+) o force in put m Spring » k ? b daw por Uso fhe föllow ir netotim a…

A: Given : To find : Equation of motion Transfer function

Q: Block A in figure 3 below has a mass of 4 kg and is on the verge of tipping as it begins to slide…

A: According to the details provided in the question, we need to calculate the coefficient of the…

Q: A given power plant has the following data: 3.5MW average load 1,500 residence P10.20 kw-hr 67,500…

A: ◆ The maximum demand is 49,950 kW-hr. ◆ Hence, the correct answer is option (C).

Q: D. D. Steam Liquid water 1 kg/s of water at 20°C enters an annular section formed by an outer tube…

A: Given: Mass flow rate of water m˙= 1kg/s Inlet temperature of water Tw,i=20oC Diameter of outer…

Q: a particle travels along a straight line with a velocity v=(12-3t^2) m/s, where t is in seconds.…

Q: For the wood beam shown in Figure A, assume L = 1.5 mand P = 15 kN. The beam cross section shown in…

Q: Q3) If in a standard vapor-compression cycle using refrigerant 22 the evaporating temperature is…

Q: The spherical gas tank is fabricated by bolting together two hemispherical thin shells of thickness…

Q: Draw the shear and moment diagrams for each beam shown in figure

Q: 2. The hollow shaft used in the system has the following conditions: B Outer Ø: 110 mm Ø Allowable…

A: Shear stress-induced in the shaft at any location (r) from the center is given by,= = 11/12Where, r…

Q: Compute the Total work of a plant if the the combined cycle overall efficiency is the, average value…

Q: Explain Second Law of Thermodynamics and give your own example.

Q: Given data : Force=2 N Area =0.2 mm2 Determine stress

A: Given:- Force = 2 N Area = 0.2 mm2 To Find:- Stress

Q: Given the data as shown in the figure, determine the (a) maximum torque Tmax(N·mm) that maybe…

Q: A helical gear has a normal diametral pitch of 12. a nor- mal pressure angle of 20°, 48 teeth, a…

Q: Summarise and discuss the working principles, functional elements, and control of Computer Numerical…

A: Additive Manufacturing (AM) is a computer-controlled method that builds actual things layer by…

Q: A riffle released a bullet from the ground at an angel of 420 degrees from the horizontal with…

Q: A pelton wheel working under a head of 50 meters, develops 80 kW at 230 rpm. Calculate the diameter…

A: Find the diameter of jet.

Q: Ageothermal power plant was installed at the rear side diff of Mayon Terrain that generates thermal…

Q: 3. Determine the torsion on the rigid supports and the maximum shearing stress developed in each…

A: The shaft is as shown below, For equilibrium, TA+TD-TC=0TA+TD=TCTA+TD=750 N.m ............. 1…

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

10. The rigid bars shown are separated by a roller and hinged at A and D. Bar AC is supported by a steel
rod at B. Calculate the vertical movement of the roller at C.
E = 200 GPa
A = 300 mm²
L= 3 m
| 50 kN
2 m
2 m
B
D
3 m
1.5 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

An aluminum [E = 10,000 ksi] control rod with a circular cross section must not stretch more than 0.22 in. when the tension in the rod is 2100 lb. If the diameter of the rod is 0.372 in., determine the maximum length of the rod.
Compute the internal diameter of the 10 m length hollow cast iron column. If the externaldiameter is two times the internal diameter and the safe compressive load on a hollowcast iron column with one end rigidly fixed and other end hinged is 60 kN. Use Euler’sformula with a factor of safety of 3 and E = 90 kN/mm2
A ladder with a uniform cross-section has a length of 4.80-foot long. It weighs W Ib. It is arranged such that one end is on the ground and the other against a vertical wall. The angle of triction at all contact surtaces is 20 degrees. What is the value of the coefficient of triction? What is f, in terms of variable Na? What is the normal force at A in terms of variable W? Answer in three decimal places
Calculate x if point B contacted with the square support? (Erod CD=200GPa; AB is a rigid bar without deformation)
SHOW COMPLETE SOLUTION AND ILLUSTRATION FINAL ANSWER IN 3 DECIMAL PLACES Problem 2: A circular rod tapers in diameter from 50 mm from one end to 20 mmon theother end for a length of 12 m. it is attached to the ceiling with its bigger end and a load P= 85 kN is suspended at its lower end. The rod has E = 200 GPa. Compute the deformation of the rod due to this load. Neglect the weight of the bar.
For the antenna tower shown, it is supported in its upright position by four high tensile wires. Given specifications of the tensile wire: E = 200 GPa, diameter = 12 mm. If a = 6 m and b = 8 m How far(horizontally in mm) would the tip of the tower move from its original position if P = 8 kN.
Problem 1): A circular pipe girder is constructed from 80mm external diameter and 60 mm internal diameter. Three such girders are mounted vertically one at equal angles of a circular horizontal platform which the girders support. The platform is 5 m above ground level and weighs (0.1*B) KN. The platform supports an additional central load of (0.2*B) KN. The weight of the girders may not be neglected. The density of the material from which the girders are constructed is (290*B) kg/m3. Assuming that each girder supports an equal share of the load, determine the compressive stresses set up in the material of each girder:1- At the lower point of the girder.2- At the middle point of the girder.3- At the upper point of the girder. Discuss the above values when the weights of the girders are neglected.Note: B = 39 Problem 2): A 20 mm diameter steel rod passes concentrically through a bronze tube (200+Q) mm long, 50 mm external diameter, and 40 mm internal diameter. The ends of the steel rod…
The bar ABCD has rigid supports and consists of three prismatic solid segments, as shown. The end segments have cross-sectional area A1 = 840 mm2 and length L1 = 200 mm. The middle segment has cross-sectional area A2 =1260 mm2 and length L2= 250 mm. Loads PB and PC are equal to 25.5 kN and 17.0 kN, respectively. Determine the magnitude of the compressive axial force FBC (kN).
Figure 1 below shows the bronze and galvani pipes are fastened to rigid supports at ends A and B and to a rigid plate C at their junction. The bronze pipe is twice as long as the galvani pipe. Two equal and symmetrically placed loads P act on the plate at C.
An aluminum bar having a cross-sectional area of 0.5 m2 carries the axial loads applied at the positions shown in Fig. Q.1A. Compute the total change in length of the bar if E = 10 × 106 kPa. Assume the bar is suitably braced to prevent lateral buckling. Note: weights in (N), Length in (mm)
The turnbuckles in the diagram shown are tightened until the compression block DB exerts a force of 12,365lb on the beam at B. Member DB is a hollow shaft with an inner diameter of 1.0 inch and outer diameter of 2 inches. Rods AD and CD each have cross-sectional areas of 1.1 square inches. Pin C has a diameter of 0.78 inch. Determine the following: a.The axial stress, in psi, in BD. b.The axial stress, in psi, in CD.c.The shearing stress, in psi, in pin C.
A compressive load of 219 kN is resisted by a rectangular strut which has one side measuring 83 mm. If the stress in the strut is 164 909 kPa, what is the length of the other side of the strut?