Circuits 1 HW 7 Q9 10.15 a) Find the rms value of the periodic voltage showntwo in Fig. P10.15.al I begovito691b) Suppose the voltage in part (a) is applied to theterminals of a 2.5 k resistor. Calculate theaverage power dissipated by the resistor.TOWOJollmoqc) When the voltage in part (a) is applied to a dif-bart 0 ferent resistor, that resistor dissipates 625 mW ofaverage power. What is the value of the resistor?Figure P10.15Vg (V)25-bug0-25 +246812010#topl7121416etc.10.1t(s)10PSIMUL

Given:a voltage signal, we need to find:a) rms value of the signal shown above. b) If it is applied…

10.15 a) Find the rms value of the periodic voltage shown in Fig. P10.15. 20 bodi b) Suppose the voltage in part (a) is applied to the terminals of a 2.5 k resistor. Calculate the al I bege 10WOO average power dissipated by the resistor. lollamaqc) When the voltage in part (a) is applied to a dif- baferent resistor, that resistor dissipates 625 mW of li Vlo average power. What is the value of the resistor? Figure P10.15 vg (V) 25 4 0 br-25 2 4 6 I padioedsel l bso I Hola! 8 10 at about 12 14 16 etc.

10.15 a) Find the rms value of the periodic voltage shown in Fig. P10.15. 20 bodi b) Suppose the voltage in part (a) is applied to the terminals of a 2.5 k resistor. Calculate the al I bege 10WOO average power dissipated by the resistor. lollamaqc) When the voltage in part (a) is applied to a dif- baferent resistor, that resistor dissipates 625 mW of li Vlo average power. What is the value of the resistor? Figure P10.15 vg (V) 25 4 0 br-25 2 4 6 I padioedsel l bso I Hola! 8 10 at about 12 14 16 etc.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The voltage (in Volts) across an element is given as v(t) = 50 cos (6ft + 21°) whereas the current (in Amps) through the element is i(t) = -20 sin (6ft +46.1°); where time, t is the time and f is the frequency in seconds and Hertz respectively. Determine the phase angle between the two harmonic functions.
The voltage (in Volts) across an element is given as v(t)= 50 cos(6ft +24.7°) whereas the current (in Amps) though the element is i(t) = - 20 sin(6ft +55°); where time, t is the time and f is the frequency in seconds and Hertz respectively. Determine the phase angle between the two harmonic functions
20 ohm in a system with a temperature of 280 Kelvin and a bandwidth of 200 MHz. The average value and the RMS value of the noise voltage that will occur in a resistor for microwave frequencies. calculate. Note: The Boltzmann constant should be used as k = 1.380x10 ^ -23 Joules / Kelvin.
A sinusoidal voltage is given by the expression v=300 cos(120πt+30∘) V.1. What is the period of the voltage in milliseconds?2. What is the frequency in hertz?3. What is the magnitude of v at t=2.778 ms?4. What is the rms value of v?
The rms value of the sinusoidal voltage supplied to the convenienceoutlet of a home in the United States is 120 V. What is the maximumvalue of the voltage at the outlet?
Consider the sinusoidal voltagev(t)=40 cos(100πt+60∘) V.1. What is the maximum amplitude of the voltage?2. What is the frequency in hertz?3. What is the frequency in radians per second?4. What is the phase angle in radians?5. What is the phase angle in degrees?6. What is the period in milliseconds?7. What is the first time after t=0 that v=−40 V?8. The sinusoidal function is shifted 10/3 ms to the right along thetime axis. What is the expression for v(t)?9. What is the minimum number of milliseconds that the functionmust be shifted to the left if the expression for v(t) is40 sin 100πt V?
Which of the following is incorrect when the information sign is m(t)=2.Sin2000πt, the carrier sign is c(t)=20.Cos(20000πt-π/3) kp=π/2 rad/Volt and kf=1000π Hz/Volt? a)S_PM(t)= 20.Cos(20000πt+πSin(2000πt)-π/3) b)S_FM(t)= 20.Cos(20000πt+2000πSin(2000πt)-π/3) c)Instantaneous frequency of PM modulated signal is f_i(t)=10000+1000π.Cos2000πt d)Instantaneous frequency of FM modulated signal f_i(t)=10000+1000.Sin2000πt
The rms antenna current for an AM transmitter increases by 15% over the unmodulated value when sinusoidal modulation applied. Find the depth of modulation. Use 4 decimal places for the final answer.
Take w1(n) = 2 sin(πn/10), and w2(n) = 1.5 cos(πn/10). What is the period of w? Find the amplitude and phase of w,given by w(n) =w1(n)−2w2(n)
Given the sinusoidal voltage ?(?)=50cos⁡(30?+10?) V. Find the following: (a) the amplitude, ?? (b) the period, T (c) the frequency, f (d) the angular frequency, ? and (e) ?(?) at t=10 ms
Consider the sinusoidal voltage v(t)=100cos(1000nt-65°)V. A. What is the maximum amplitude of the voltage? B. What is the frequency in HERTZ and in RADIANS PER SECOND? C. What is the phase angle in RADIANS and in DEGREES?
The given data to be used for getting the RMS Values is 0, 5, 10, 30, 50, 70, 50, 30, 10, 5, 0, -5, -10v. Find the RMS value.