100 mm 75 mm 150 mm 200 mm 100 mm 150 mm 100 mm CE PROBLEM 8.29 The solid shaft AE rotates at 600 rpm and transmits 45 kW from the motor M to machine tools connected to gears G and H. Knowing that Tall = 55 MPa and that 30 kW is taken off at gear G and 15 kW is taken off at gear H, determine the smallest permissible diameter of shaft AE.

100 mm 75 mm 150 mm 200 mm 100 mm 150 mm 100 mm CE PROBLEM 8.29 The solid shaft AE rotates at 600 rpm and transmits 45 kW from the motor M to machine tools connected to gears G and H. Knowing that Tall = 55 MPa and that 30 kW is taken off at gear G and 15 kW is taken off at gear H, determine the smallest permissible diameter of shaft AE.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Three shafts and four gears are used to form a gear train that will transmit 6.7 kW from the motor at A to a machine tool at F. (Bearings for the shafts are omitted in the sketch.) Knowing that the frequency of the motor is 30 Hz and that the allowable stress for each shaft is 60 MPa, determine the required diameter of each shaft. The required diameter of shaft AB is mm. The required diameter of shaft CD is mm. The required diameter of shaft EF is mm.
A steel shaft must transmit 150 kW at a speed of 360 rpm. Knowing that G = 77.2 GPa, design a solid shaft so that the maximum shearing stress will not exceed 50 MPa and the angle of twist in a 2.8-m length must not exceed 3°. Consider the frequency f to be 6 Hz. The diameter of the solid shaft is -- mm
The preliminary design of a motor-to-generator connection calls for the use of a large hollow shaft with inner and outer diameters of 4 in. and 6 in., respectively. Knowing that the allowable shearing stress is 12 ksi, determine the maximum torque that can be transmitted by (a) the shaft as designed, (b) a solid shaft of the same weight, and (c) a hollow shaft of the same weight and an 8-in. outer diameter.
Two solid steel shafts, each 30 mm in diameter, are connected by the gears shown in the figure. Knowing that G = 77.2GPa, determine the angle through which end A rotates when a couple of magnitude T = 200Nxm is applied to A.
A hollow steel (G = 12,000 ksi) shaft has diameters of 6 in. and 4 in. and an allowable shearing stress of 9,000 psi. Determine a. the horsepower transmitted at 25 rad/sec; b. the magnitude of the angle of twist in a length of 10 ft; and c. the required number of 3⁄4-in diameter bolts for a flange coupling in which two-thirds of the bolts are on a 12-in diameter bolt circle and one-third are on a 9-in diameter circle. The allowable shearing stress in the bolts is 12,000 psi.
Gear B supplies 15 kW of power, while gears A, C and D withdraw 6 kW, 4 kW and 5 kW, respectively. If the shaft is made of steel with the allowable shear stress of tallow = 75 MPa, and the relative angle of twist between any two gears cannot exceed 0.05 rad, determine the required minimum diameter d of the shaft to the nearest millimeter. The shaft is rotating at 600 rpm.
Under normal operating conditions, the electric motor exerts a torque of 2.4 kN·m on shaft AB. Each shaft is solid with diameter d 52 mm. In order to reduce the total mass of the assembly, a new design is being considered in which the diameter of shaft BC will be smaller. Determine the smallest diameter of shaft BC for which the maximum value of the shearing stress in the assembly will not be increased. The smallest diameter of shaft BC is mm.
1. A steel shaft is to be manufactured either as a solid circular or as circular tube. The shaft is required to transmit a torque of 1200 Nm without exceeding an allowable shear stress of 40 MPa, nor an allowable rate of twist of 0.75º/m. For G = 78GPa, determine: a. The required diameter do of the solid shaft.b. The required outer diameter d2 of the hollow shaft if the thickness t of the shaft is specified as one-tenth of the outer diameter.c. The ratio of diameters (that is, the ratio d2/do and the ratio of the weights of the hollow and solid shafts.
A hollow shaft's inner diameter is half of its outer diameter D. Show that the maximum torque that this shaft can carry is 15/16th of the maximum torque that a solid shaft of diameter D made of the same material can carry.
Under normal operating conditions a motor exerts a torque of magni-tude TF= 1200 lb·in. at F. Knowing that rD= 8 in., rg= 3 in., and the allowable shearing stress is 10.5 ksi in each shaft, determine the required diameter of (a) shaft CDE, (b) shaft FGH.
Q2: A solid steel shaft A of 60 mm diameter rotates at 300 rev/min. Find the greatest power that can be transmitted for a limiting shearing stress of 60 MN/m2 in the steel. It is proposed to replace A by a hollow shaft B, of the Same external diameter but with a limiting shearing stress of 75 MN/m2 . Determine the internal diameter of B to transmit the same power at the same speed.
Two shafts, each of 7878 -in. diameter, are connected by the gears shown. Knowing that G = 11.2 ×106 psi and that the shaft at F is fixed, determine the angle through which end A rotates when a 1.4-kip·in. torque is applied at A.