I need answer within 20 minutes please please with my best wishes lo02/A timbep beam is reinforced WithSteel Plates vigdly attached at the top andbottom as Shown in fi'g P- 1002 By Whatqumokut is the moment increased bythe reinforcement if n= 15 and theallowable stresses i'n the Wood and steelave 8 mpa and 120 MPa respectively?K-150- mm300mmtomtmm250

Answered: Image /qna-images/answer/e5a2088e-ffb4-490a-ac8c-48d570ffdb49.jpg

1002/ A timber beam is reinforced with Steel Plates rigidly attached at the top and bottom as shown in Fig P-1002. By What amount is the moment increased by the reinforcement if n = 15 and the -Allowable stresses in the Wood and steel are 8 mpa and 120 MPa respectively? K-150mm k Tomm mm 250 mm 300mm Tomm

1002/ A timber beam is reinforced with Steel Plates rigidly attached at the top and bottom as shown in Fig P-1002. By What amount is the moment increased by the reinforcement if n = 15 and the -Allowable stresses in the Wood and steel are 8 mpa and 120 MPa respectively? K-150mm k Tomm mm 250 mm 300mm Tomm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.6.1P: A steel bar has a square cross section of width b = 2.0 in. (sec figure). The bar has pinned...

See similar textbooks

Similar questions

Torsional T is applied to the hollow axis (G=80 GPa). Ewha Womans University, the maximum shear strain is γmax = 640 × 10-6rad Igo, inside andThe outside diameters are 120mm and 150mm, respectively.a. What is the maximum axial strain?b. Maximum axial stress?c. What is the maximum torque (T) meeting the above conditions?
If the shear modulus of a material is 120GPa & the bulk modulus is 140 GPa, then Young’s modulus is------ a. 820 GPa b. 280 Pa c. 280 GPa d. 820 Pa
A steel rod of 30 mm diameter is enclosed centrally in a hollow copper tube of external diameter 40 mm and 5 mm thick. The composite bar is then subjected to an axial pull of 45 kN. If the length of the compound rod is 150 mm , and the elasticity moduli are Est = 200 GPa and Ecu = 100 GPa , determine: 1.2.1 The stresses in the rod and tube
Internal loadings at a critical section along a steel drive shaft are given. If theyield stress under tension and shear are S_y = 800 MPa, respectively, determine the maximum length of the shaft using the maximum-shear-stress theory (Tresca yield theory) in a way that the shaft does not fail neither at A nor at B. （DON'T COPY OTHER ANSWER) AND 30mm is radius
A two-story building has steel columns ABin the first floor and BC in the second floor, as shownin the figure. The roof load P1 equals 400 kN, and thesecond-floor load P2 equals 720 kN. Each column hasa length L = 3.75 m. The cross-sectional areas of thefirst- and second-floor columns are 11,000 mm2 and3900 mm2, respectively.(a) Assuming that E = 206 GPa, determine thetotal shortening δAC of the two columns due tothe combined action of the loads P1 and P2.(b) How much additional load P0 can be placedat the top of the column (point C ) if the totalshortening δAC is not to exceed 4.0 mm?
A prismatic bar with a length L = 3 ft andcross-sectional area A = 8 in2 is compressed by anaxial centroidal load P =10 kips. Determine thecomplete state of stress acting on an inclined sectionpq that is cut through the bar at an angle θ = 35°, andshow the stresses on a properly oriented stress element.
In a 2.5 cantilevered I-beam, 2500 kg weight is applied at 0.75 meter from the free end. If the allowable stress in beam is 120 Mpa, determine the section modulus and The base and height of the beam if the base is 75% of its height mm.
A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?
A pole is fixed at the base and is subjected to a linearly varying distributed force with maximum intensity of q0and an axial compressive load P = 20 kips at the top (see figure). The pole has a circular cross section with an outer diameter of 5 in. and an inner diameter of 4.5 in. Find the normal stresses on the surface of the pole at the base at locations A and B.
A plain concrete wall (i.e., a wall with no steel reinforcement) rests on a secure foundation and serves as a small dam on a creek (see figure). The height of the wall is h = 6.0 ft and the thickness of the wall is t = 1.0 ft. Determine the maximum tensile and compressive stresses o*!and trt, respectively, at the base of the wall when the water level reaches the top {d = h). Assume plain concrete has weight density ye= 145 lb/ft . Determine the maximum permissible depth dnuxof the water if there is to be no tension in the concrete.
A retaining wall (Fig. a) is constructed using steel W-shape columns and concrete panel infill (Fig, b). Each column is subjected to lateral soil pressure with peak intensity q0(Figs, b and c). The tensile and compressive strength of the beam is 600 MPa. Select the most economical W 360 section from Table F-l(b) based on safety factor of 3.0.
A square wood column with side dimensions b (see figure) is constructed of a structural grade of southern pine for which Fc= 10,5 MPa and E = 12 GPa. An axial force P = 200 kN acts on the column. If the dimension b = 150 mm, what is the maximum allowable lensth Lmax, of the column? If the length L = 4.0 m, what is the minimum required dimension bmin?