11 .625 .125 SECTION A-A VIEW B-B .344 1.000 .313- 0.2407+.0013 -.0013 10 .125 8 B A Q 3.875 NO PAINT -2X-24UNF-2B 2.938

Q: The frame ACD is hinged at A and D and is supported by a cable that passes through a ring at B and…

A: To find: The moment about the diagonal. Given: The tension in the cable is T=550 N. The frame is…

Q: Find the velocity field and volumetric flow rate for two stationary plates, imposing pressure p0 on…

A: The case of pressure uniform pressure gradient is given. It is required to determine the velocity…

Q: an ericson cycle operates on 0.75 lbm ocygen from 60 psia and 1200degree F at the beginning of the…

A: To Find : The value of QA,QR,Wnet,η,Pm Given : The pressure is, P3=60Psia6.894kPa1Psia=413.64kPa The…

Q: Suppose that the following rod system is subjected to a specific amount of load that makes the…

A: Introduction We will compute the stress at node 1 in this issue, but first, we will calculate the…

Q: What cutting-edge tech is currently in the works?

A: Cutting-edge technology is the technology in which technology is capable of performing the work…

Q: P24-1. The assembly shown is welded to collar A that fits on the vertical pin shown. The pin can…

A: To Find : The tension in each cable and reaction at A. Free Body Diagram : Th F.B.D is,

Q: What is the pressure drop that arises from a Lid-driven cavity flow?

A: A Lid-driven cavity flow refers to the motion of a fluid contained within a square or rectangular…

Q: 1. The working substance for a Carnot cycle is 8 lbm of air. The volume at the beginning of…

A: Given data: The mass of the air is m=8 lb The volume at the point 1 is V1=9 ft3 The pressure at the…

Q: A structure is attached to the ocean floor as shown in the figure below. A 2-m-diameter hatch is…

A: Given: The angle made by the hatch from the horizontal: →θ=28° And diameter of the hatch→D=2 m So…

Q: a) A suction pump. Consider a pipe that is inserted vertically into water. By suction, the pipe is…

A: According to Bartleby guidelines, we can solve three subpart of a question at a time. Please post…

Q: 1) Determine the magnitude of the resultant force. Express your answer in pounds to three…

A: Given the value of the three forces  Required: Resultant force and couple about point A.

Q: ind the moment caused by the force about point A, resultant force, and x-bar (M, R, x). Dont forget…

A: According to the given data  A loading beam is given  We need to find  moment caused by the force…

Q: A centrifugal pump is to deliver 227 m³/hr of water from a source 4 meters below the pump to a…

A: Given data: A centrifugal pump delivers 227 m3/hr of water from a source 4 meters below the pump…

Q: 7. Determine the net torque about the axle of the wheel shown to the right in terms of F and R 2F 2R…

A: According to the question. a force system, at wheel We need to find Torque

Q: A 500 N RAY K ↓ 1<im-31 Im 4m 500 B Re

A:

Q: The 58-mm-diameter cylinder is made from Am 1004-T61 magnesium and is placed in the clamp when the…

A:

Q: Vibration is ubiquitous. It is seen in everyday life applications.  Discuss the typical applications…

A: Vibration is a mechanical phenomenon in which oscillations of particles occur about an equilibrium…

Q: Find the centroid of the following figure, explain the procedure used to obtain it, step by step

A:

Q: Determine the maximum axial force P that can be applied so as not to exceed an allowable tensile…

A:

Q: 2. See Figure P12-2. The shaft rotating at 200 rpm carries a spur gear C having 80 teeth with a…

A:

Q: Determine the components of reaction at A and B. Take that P = 430 N and M = 700 Nm .(Eigure 1)…

A:

Q: Hot combustion gases, modeled as air behaving as an ideal gas, enter a turbine at 10 bar, 1500 K and…

A: One can use the First Law of Thermodynamics to determine the rate of heat transfer from the turbine…

Q: Express the force F1 and F2 in Cartesian vector form. Determine the magnitude of the resultant…

A:

Q: It's crucial to tell the difference between a pair of cold boots and a warm pair of boots.

A: To find: The difference between a pair of cold boots and a warm pair of boots.

Q: Two couples act on the beam (Figure 1). Figure 200 lb 1.25 1 of 1 > It F = 137 lb, determine the…

A:

Q: Under elestic condition, calculate the ave. forge and pressure of a closed window when a 500 water…

A: To Find : The average force and pressure of closed window. Given : The number of water ice is n=500…

Q: 7.3 Orifice meters are used to measure the flow rate of a fluid. In an experiment, the flow…

A: Given: Here is the given formula, K=Mt×Ap2×g×∆h12 Where, Mass, M=865.00±0.05 lbm Time, t=600.0±1s…

Q: 12 Problem 02.086.a - Hooke's Law for shearing stress and strain . Determine the change in volume of…

A:

Q: Determine the displacements at all nodes for the plane truss shown (Hint: you do not need to develop…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: P25-1. Member ABCE is supported by three separate cables, DB, DC, and EF. The load at G has a weight…

A:

Q: The weights of the various components of the truck are shown in (Figure 1). Replace this system of…

A: To Find : a)The magnitude of the resultant force. b) The location Free Body diagram :

Q: A 4-kg sphere rests on the smooth parabolic surface. Determine the normal force the ball A exerts…

A: Introduction Using the static equilibrium equation, we will calculate the normal force exerted by…

Q: The 80-kg lamp is supported by two rods AB and BC as shown in Fig. 1-16a. If AB has a diameter of 10…

A: Given Data- Lamp mass m=81kg Diameter of AB =5mm Diameter of Bc =8mm We have to find normal stress

Q: The vertical distance above a reference datum to a point is called the point’s

A: ▪︎We have to specify the term related to the vertical distance above the reference datum to a point.…

Q: Q2. Rigid member DEF is supported by three rods, AD, BE, and CF, and the rods are of the same…

A:

Q: EXERCISE 2.34 The cable, whose length is 300 mm, is fastened to the 500-g block. Clockwise rotation…

A: The mass of the block is m=500 g=0.5 kg. The coefficient of sliding friction is μ=0.4. The angular…

Q: A 0.09 kg tennis ball traveling at 15 m/s rebounds in the opposite direction at 20 m/s after being…

A: This question is based on the concept of momentum conservation and impulse momentum theorem.

Q: Consider a cylindrical metal 16 mm in diameter and 70 mm long is pulled in tension. It is known that…

A: Given data:- Initial length of the specimen =70 mm Final length of the specimen=76 mm To find:- The…

Q: assume there is damping in the system such that ζ=0.2

A: Write the given data. k1=k2=5000 N/ma=0.25 mb=0.5 ml=1 mM=50 kgm=10 kgF0=500 Nω=1000 rpm

Q: The assembly has the diameters and material make-up indicated. It fits securely between its fixed…

A:

Q: 8. In the figure below, the velocity of the boats shown are A = 37 m/s and v= 56 m/s. Answer the…

A: Given: VA = 37 m/s VB = 56 m/s Required: (a). v→A ( velocity vector of car A ) (b). v→B ( velocity…

Q: Problem 5. EOM Derivation Derive the equation of motion for the following system: A solid cylinder,…

A: Given the spring stiffness and initial displacement.  Required: Equation of motion.

Q: The cantilever beam is subjected to a uniform distributed load (g) and a concentrated force (F), at…

A:

Q: Problem 2. EOM Derivation Derive the equation of motion for the following system: 77 m y(t) k IM Dry…

A: To determine: Derive the equation of motion for the following system:

Q: The Fourier heat conduction equation has been used to obtain the temperature-time response during…

A:

Q: Design a crank-rocker linkage that will move the rocker link between two extreme positions 45…

A: Solution: Given Data and to find: Design a crank-rocker linkage that will move the rocker link…

Q: Determine the Centroid of the lines/curve shown shown: 5cm 6cm a. x = 0; y = 0 b. x = 1; y = 0 c. X…

A:

Q: At the instant shown = 45 deg and w = 9.2 rad/s. Link AB is currently vertical. First calculate the…

A: According to the given data ω=9.2rad/s OA=5.2 m We need to find

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.