11. *Design a bandpass filter of the form in the figure below, with a lower cutoff frequency of 20.1kHz and upper cutoff requency 20.3kHz. Take R=20k. Calculate L, C and Q. L C + v¡ (t) % (1) Answer: 15.915H, 3.9pF and 101. R

11. *Design a bandpass filter of the form in the figure below, with a lower cutoff frequency of 20.1kHz and upper cutoff requency 20.3kHz. Take R=20k. Calculate L, C and Q. L C + v¡ (t) % (1) Answer: 15.915H, 3.9pF and 101. R

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: S + ď laplace 6 1872) (5+4) Inverse Transform

A: (i) Given data, Function is given as, FS=SS+2S+4

Q: b. Given the digital signals x(n) in Fig.1, write an expression for digital signal using the…

Q: 2. Determine the stability for the following linear system y(n) = 5x(n) + 30x(n-3) - 10x(n - 20)

A: Given,The linear system is,yn=5xn+30xn-3-10xn-20

Q: Q4. [14 Marks A DC shunt motor is supplied by 250-volt and 15kW at rated load, if the No-load speed…

Q: A 2-wire d.c. distributor cable AB is 2 km long and supplies loads of 100A, 150A,200A and 50A…

A: It is a two wire distribution system with distributor fed at one end: Here, the distributor is fed…

Q: 1) Determine the response of the system to the input signal: X (n) = Scm) - =—= Sen-1) any pole-Zero…

Q: Find v, for the circuit below. 5 0 10 sin (5000) 30°) V + 40 μF 80 2 sin (8000 + 10°) A

A: In this question, We need to determine the voltage v as shown the circuit using the super position…

Q: 1. The diagram below shows a typical data acquisition system where an analogue signal from a…

A: Data acquisition system is used to perform some necessary operations on data. Figure shows the block…

Q: A schematic of a buck converter is shown below. Vin is the DC Input voltage. CTRL is a control…

A: Given A schematic of a buck converter is shown below. Vin is the DC Input voltage. CTRL is a…

Q: A single phase transformer on open circuit condition gave the following test results: Applied…

A: From the question, it is given that Applied voltage Frequency Power drawn 192 V 40 Hz…

Q: Find VTH, ZTH, and IN for the circuit shown below for R = 2 ohms. 3 Ω j4 Ω 10/40° V 6 Ω 1) 2/20° A…

A: For the above given question by calculating open circuit voltage across the given terminal we need…

Q: BJT Emitter Follower: Draw the small-signal model for the common-collector amplifier shown below.…

A: The given amplifier is in common collector configuration because input signal is applied at base…

Q: If resonant frequency, wo = 1100 rad/s, find the following: a) L in mH; b) Quality factor Q; c)…

A: In this question parallel RLC resonance is given...We have to find out L, Q factor , bandwidth…

Q: PZ 4- A 4-pole generator has a wave-wound armature with 722 conductors and the armature current is…

Q: Qz/ind Fourier transform of the signal given below, and then find the amplitude spectrum X() and the…

A: In this question we need to find a Fourier transform , amplitude and phase spectrum of the given…

Q: Find VTH, ZTH, and IN for the circuit shown below for R = 2 ohms. 3N j4 R 10/40° V 6 Ω 2/20° A go

A: In this question, We need to determine the Thevenin voltage, Thevenin impedance and norton current…

Q: Find VTH, ZTH, and IN for the circuit shown below for R = 2 ohms. 3N j4 Ո R 760 2/20° A 10/40° V

A: The circuit diagram is shown below, Where,R=2 Ω

Q: 30 V DC generators are operating

A: Three Phase Synchronous machine- This Synchronous machine comprises of rotor and stator as it basic…

Q: 4. What is an emergent property? O a. a property that a system has but that its individual component…

A: Given: Emergent property

Q: * A 16 N force produce a moment of 64 Nm. the moment arm is; O 4m O √2m O2m O 8m

A: We need to find out moment arm .

Q: c. A basic d'Arsonval movement instrument has been converted to operate as a series ohmmeter with an…

A: c) A d'Arsonval movement instrument is operated as a series ohmmeter Internal resistance = 100 ohms…

Q: A 230 V DC shunt motor has a full-load efficiency of 89.9%. Rated (full) load is 40 hp. Motor…

A: As per the guidelines of the bar

Q: how many hours do you need to charge a 3.7 , 2600 mah li-ion battery on TP4056?

A: Given: A 3.7 V, 2600 mAh li-ion battery on TP4056. To find: How many hours are needed to charge the…

Q: 2. Find the RMS value of the voltage waveform and the average power absorbed by the 9 ohms resistor…

A: In this question we need to find a RMS value of the given voltage waveform and average power…

Q: 5. Solve for vix @ t = 0. ヤ

Q: Compute for Ib, Ic, Ie

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: B. Answer the following: 1. Give two differences Between the characteristics of Shunt and Series…

A: Given We need to find the difference between the shunt and series motor,self excited and seperately…

Q: 1. Find the currents I, and I,. 2. Find the voltages V, and V3. 10A R₁60 E24V 60 80 V₂

A: given here a electrical circuit and asked to find the I1 , Is , Vs , V3 .

Q: What distance should a 2N load placed from the pivot so that the see saw won't move? 0.3 m ? m 3N O…

A: We need to find out distance for 2N force .

Q: 1. Mark on an Argand diagram the points representing the following numbers: (a) 2 (b) 3i (c)-i (d)…

Q: Q1. Multiple Choice Questions (MCQ): 1. For a horn antenna, in which flaring is done only in one…

A: As per guidelines given to us we can only provide the solution of first question in multiple type of…

Q: D) ANSWER IT. А ВС э

A: To implement using NAND GATE

Q: 2. Find the RMS value of the voltage waveform and the average power absorbed by the 9 ohms resistor…

A: Power: It is the time rate of the change of energy. It can be absorbing or expanding and its unit is…

Q: Z Given H(Z) = (Z-0.5) (Z+0.8) Find hen) and write and draw region of convergence Roc for the…

Q: Its main purpose is to reduce the noise figure that could be a problem because of the large…

A: In this question ,we will write about amplifier to reduce noise figure....

Q: A 20 kVA, 2000/200-V, 50 Hz transformer has a high voltage winding resistance of 0.2 2 and a leakage…

A: Resistance: It is a property of a material that resists the flow of the current. This is denoted…

Q: Q3. Consider the sequence: x(n) = 48(n) + 38(n-1) + 28(n-2) + 8(n-3) Let X(k) be the six-point DFT…

Q: The (Z₁2 3+ 14 magnitude of the Complex number 22= 4-√3) is unity

A: Given: Complex number Z1=3+j4Z2=4-3j

Q: 5. Use Kirchhoff's Laws to calculate the potential difference and the current across each resistor…

A: In this question, We need to determine the potential difference and current in the each resistance…

Q: (a) Find the Fourier Transform of the impulse response, h[n] = 8[n] + 28[n 1] + 28[n-2] +8[n-3]. (b)…

Q: Q5. A 20 kVA, 2000/200-V, 50-Hz transformer has a high voltage winding resistance of 0.2 2 and a…

Q: For the electric network shown, the frequency response function is: 10 Ω www O + + vy(t) 1F= ₂(1)…

A: We need to find out Transfer function of given system

Q: 0. Modern transistors have now reached the limits in small sizes. We can now fit a maximum of about…

A: As per Bartleby policy we can answer only three questions at a time. I am answering first three for…

Q: Q2- 100 KVA, (6600/330) ,single-phase transformer, the primary connected to supply voltage 100 V and…

A: Transformer is a static device which is used to step up or down the voltage level or current level…

Q: In your answers below you may use sqrt(), but no trig functions, complex multiplication, or powers.…

A: As per our guidelines we are supposed to be the first question only. Kindly repost the other…

Q: 91. Choose only seven for the following: 1) ******** ............of measurement is difference…

A: Given Multiple choice questions based on measurement. Please find the below attachment for clear…

Q: Q2/ A 250 V shunt motor has an armature resistance of 0.25 0 and field resistance of 125 Q. At…

Q: A 60052 resistor is connected across the 60052 antenna input of a receiver. The bandwidth of the…

Q: Two unlike parallel forces, each of magnitude 50 kN are 200 mm apart from each other. what will be…

Q: An electron in a TV picture tube moves toward the front of the tube with a speed of V = 5.10 m/s.…

A: Given data, Charge on electron q=1.6×10-19 C Velocity of electron v=5×106 m/s Magnetic field B = 0.1…

Concept explainers

Filter

A filter is a device or process which removes some of the unwanted features or components like frequencies from a signal in signal processing. The feature of filters is the complete or partial suppression of some part of the signal, and filtering is a class of signal processing. This most often means removing some frequency bands or some frequencies. In the frequency domain, the filters do not exclusively act, especially in the image processing field many other targets for filtering exist. Without having to act in the frequency domain, the correlations can be removed for certain frequency components and not for others. The filters are widely used in electronics and telecommunication, in television, radio, radar, audio recording, music synthesis, control systems, computer graphics, and image processing.

Question

11. *Design a bandpass filter of the form in the figure below, with a lower cutoff
frequency of 20.1kHz and upper cutoff requency 20.3kHz. Take R=20k. Calculate L,
C and Q.
L
C
m
v¡(t)
v (t)
Answer: 15.915H, 3.9pF and 101.
R
+

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

1. A tuned circuit has a resonant frequency of 18 MHz and a bandwidth of 120 kHz. What are the upper and lower cutoff frequencies?2. What value of Q is needed to achieve a bandwidth of 4 kHz at 3.6 MHz?3. A filter has a 6-dB bandwidth of 3500 Hz and a 60-dB bandwidth of 8400 Hz. What is the shape factor?
The filter as shown is designed with R1 = R2 = 2.26 kΩ, R3 = ∞, C1 = 0.02 μF,and C2 = 0.01 μF. What are the new values of C1, C2, R1, R2, fo, and Q if the impedance magnitude is scaled by a factor of (a) 5 and (b) 0.885?
For a basic passive RLC bandpass filter, I am calculating the values of RLC for a specific resonance frequency and bandwidth. The resistor is 1 kilo-Ohm. For a bandwidth of 600 Hz, and a resonance frequency of 2kHz, what are the values of L and C given the following equations:Bandwidth = R/Lω0 = (1/LC)^(1/2)
The operational amplifier circuit shown in the figure is used as a high pass filter. Assume:C=150nF, Ro=200ΩR1 =2kΩ , R2 =6kΩDetermine:A. The Vo/Vs gain in decibels in the bandwidth.B. The cutoff frequency.
Design a bandpass filter with cutoff frequencies 20k Hz and 80k Hz, with ?=8. (a) Draw your circuit, labeling the component values and the output voltage.(b) 8.4k Ω.(c) What is the central frequency?
Answer the following wuth illustration and solutions. 1.) A second-order band pass filter is to be constructed using RC components that will only allow a range of frequencies to pass above 500Hz and below 1.5kHz. Assuming that both the resistor have values of 1kohms, calculate the values of the two capacitors required. Find also the center frequency of the two frequencies. This is the example/guide that might help.
Sketch a Bode plot, using straight-line approximation, for the range of frequencies from 1 Hz up to 1 MHz. Include magnitude and phase plots. put magnitude in dB. Graph should include: -how fast the transfer function “rolls off” below the cut-off frequency (in dB/decade) -the phase and amplitude for the three frequencies: ω = ωC, ω = 10∗ωC, ω = 0.1∗ωC fc = 500 Hz ωC = 2π(fc) This is for a passive high pass filter (single resistor, single capacitor)
Calculate the center frequency, the bandwidth, and the qualityfactor of a bandpass filter that has an upper cutoff frequency of121 krad/s and a lower cutoff frequency of 100 krad/s.
Find the transfer function for the circuit shown in figure 1. Plot the amplitude graph of 2logh10hw and the phase angle graph of H(jw)? Calculate the actual cutoff frequency? Calculate the true phase angle at the cutoff frequency?
DERIVE frequency transfer function of the filter circuit.( NEED ONLY HANDWRITTEN SOLUTION in 3 steps PLEASE OTHERWISE DOWNVOTE).
Find a chebyshev bandpass filters function to meet the following specifications: center frequency at 1500 rad/sec bandwidth is 200 rad/sec passband ripple= 1dB 20 dB attenuation at the stop frequency of 1200 rad/sec and 1800 rad/sec
For the following bandpass filter circuit, select the circuit elements in order to satisfy the following specifications: fl= 100Hz fu= 200Hz First, consider the lowpass filter on the left, which has a transfer function Hw= Rf1/R11 1/Rf1C1jw+1 The desired lowpass transfer function, written in hertz frequency, is H(w)= -1/(jf/fu+1) If R1 is selected to be 1000Ω then determine R11 in ohms. Enter R11. Omit the units. (hint: remember to convert between fand w when needed) Referring to question 1, what is C1 in μf Consider the highpass filtter on the night, which has a transfer function H(w)= - Rf2/R12 R12/C2jw/R12C2jw+1.The desired highpass transfer function is -if/ft/if/ft+1. If R12 is selected to be 1000Ω then determine Rf2 in ohms and C2 in μf.Enter Rf2 (hint: remember to convert between fand w when needed) Referring to problem 3, what is C2 in μf