11. For the network of Fig. 9.79: a. Determine the mathematical expression for the magnitude of the ratio Vo/Vị- b. Using the results of part (a), determine Vo/V; at 100 Hz, 1 kHz, 2 kHz, 5 kHz, and 10 kHz, and plot the resulting curve for the frequency range of 100 Hz to 10 kHz. Use a log scale. c. Determine the break frequency. d. Sketch the asymptotes and locate the - 3-dB point. e. Sketch the frequency response for Vo/V; and compare to the results of part (b). 0.068 µF + V; 1.2 k2. Vo FIG. 9.79

11. For the network of Fig. 9.79: a. Determine the mathematical expression for the magnitude of the ratio Vo/Vị- b. Using the results of part (a), determine Vo/V; at 100 Hz, 1 kHz, 2 kHz, 5 kHz, and 10 kHz, and plot the resulting curve for the frequency range of 100 Hz to 10 kHz. Use a log scale. c. Determine the break frequency. d. Sketch the asymptotes and locate the - 3-dB point. e. Sketch the frequency response for Vo/V; and compare to the results of part (b). 0.068 µF + V; 1.2 k2. Vo FIG. 9.79

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Build Circuit 1b in Multisim. Using MultiSim’s Oscilloscope, display and measure the voltages including the phase angles with respect to the input voltage. THIS IS 1b Problem: 1b) For the circuit shown , let R= 1kohm, L1 = 10mH, C1= 50nF. Calculate the values of Z, Phase Shift, I, Vr, Vc, VL , PR, PAPP and Power Factor. Do this for V1= 10 V at 10000Hz. Find resonant frequency. Measure phase shift like so: a) Measure the difference in times of the peaks for the two different waves. b) Divide this difference by the period length. The ratio tells you what fraction of a cycle the time difference is.c) One cycle is 360 degrees (or 2π radians) so multiply the fraction in step 2 by 360 degrees to convert that time difference into a phase shift (degrees)
Q10. If the impedance of a circuit = 20 – j10n, if a voltage source is connected across this impedance, which if the following statements is correct?
if the value needed,a : 9b : 9
The load is connected to 100V (rms) and dissipates 1kW at lagging power factor of 0.9. Find the phasor V1 where VL=100<0 degree and frequency equals 400 rad/s.
Impedance of AC circuit and Admittance of AC circuitSHOW THE CIRCUIT USING ANY SOFTWARE OR YOU CAN DRAW IT MANUAALYY thNAKSS
21. In the phasor diagram of balanced star connected system the angle between VR and VRY is -30 degree. Select one: True False
From the choices below, select which impedance diagram most accurately illustrates the impedance of a 120 kΩ resistor. Note the impedance is represented on the polar plot by the red line.
QI Consider the circuit of Figure (1) z )0+ j40 Q Figl a. Calculate the sinusoidal voltages v1 and v2 using phasors and the voltage divider rule. b, Sketch the phasor diagram showing E, V1, and V2
find apparent power of source.
Example 9.15
Determine the Phasor values of V1 and V2
Calculate in the circuit of Fig. 9.51.