11. In an RC series circuit EMF = 120.0 V, R = 1.40 MQ, and C = 1.80 µF. (a) %3D Calculate the time constant. (b) Find the maximum charge that will appear on the capacitor during charging. (c) How long does it take for the charge to build up to 20 uC? (d) What is the maximum current through the resistor? (e) What is the potential difference across the capacitor after it has been charging for 1.0 sec? (Đ Sketch the charge and current as functions of time. (g) After being totally charged, the capacitor is carefully disconnected from the circuit above without discharging it. It is connected to a 520 kQ resistor and begins to discharge. What is the time constant for this circuit? (h) What will be the potential difference across the capacitor after 400 msec? (i) Sketch the charge and current as functions of time.

11. In an RC series circuit EMF = 120.0 V, R = 1.40 MQ, and C = 1.80 µF. (a) %3D Calculate the time constant. (b) Find the maximum charge that will appear on the capacitor during charging. (c) How long does it take for the charge to build up to 20 uC? (d) What is the maximum current through the resistor? (e) What is the potential difference across the capacitor after it has been charging for 1.0 sec? (Đ Sketch the charge and current as functions of time. (g) After being totally charged, the capacitor is carefully disconnected from the circuit above without discharging it. It is connected to a 520 kQ resistor and begins to discharge. What is the time constant for this circuit? (h) What will be the potential difference across the capacitor after 400 msec? (i) Sketch the charge and current as functions of time.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Given the capacitance of four capacitors Ca= 30 µF, Cb = 20 µF, Cc = 40 µF and Cd = 10 µF. If Cb and Cc are connected in parallel and the parallel combination is connected in series with Ca and the combination is further connected in parallel with Cd, calculate (a) the equivalent capacitance (b) the voltage across each capacitor if the circuit is supplied by 240 volts DC source (c) the charge on each capacitor.
A 150-volt electromotive force is applied to an RC-series circuit in which the resistance is 1500 ohm and the capacitance is 5 micro Farad (uF). If q(0)=0, find the charge and current at t=0.005 s. charge: q = micro Farad (uF) current: i = milli ampere (mA) Determine the charge as t approaches infinity. charge: q= micro Farad (uF)
The voltage pulse applied to the 100 mH inductor shown is 0 for t<0 and is given by the expression v(t)=20te−10t V for t>0. Also assume i=0 for t≤0. Sketch the current as a function of time.
A circuit with a supply voltage of 2.5 V is being powered through a package. The packagehas a resistance of 100 m and a certain inductance L. The circuit requires at least 2.25 Vto function correctly. If this voltage is required in a time of 1ns, calculate the effectiveinductance L for the package.
In the circuit shown, let Eo= 10[V], R = 3[Ω], and L =0.6[H]. The switch is closed at time t = 0. From time t = 0 to t = L/R. (a) Find the total energy that has been supplied by the battery. and b) Calculate the total energy that has been dissipated in the resistor, and (c) Determine the energy that has been stored in the inductor. (Hint: Find the rates as functions of time and integrate from t= 0 to t = L/R.)
A current of 5A flows in a resistor of 2 ohms. 18 kJ is the energy dissipated in 300 seconds in the resistor. True/False Linear Circuit is the one whose parameters are not constant. True/False Choke is used to limiting the current flowing through it. True/False In an Inductive circuit, relationship between inductance (L) is directly proportional to the inductive reactance (XL). True/False
Capacitance= 4uF , Hence time constant is 5.33μs For the capacity value, calculate the estimated time to come to the final state.Plot capacitor current and voltage graphs and show if it works in harmony with the time constant you calculated. NOTE: if you want you can use falstad online circuit simulator.
A resistance of 100 Ω, an inductance of 0.1 H, and a capacitance of 5(10−5) F are connected in series.If the total electromotive force is given by 110 sin 377t, such that at t = 0,Q = 0, and i = 0, find thecurrent for t > 0.
3. A ceramic capacitor has an effective plate area of 5cm2 separated by 0.1mm of ceramic of relative permittivity of 100. Calculate the capacitance in microfarads. If the capacitor is given a charge of 1.5 µC what will be the potential difference (pd) between plates? & calculate the energy stored in it
The distance between the parallel two plates is 4d, the area of the parallel plates is A / 2 andif the energy stored in the system is 2W, the potential difference between the plates is W andFind in C (capacitance)?
capacitor having capacitance of 10uF is connected with 1k ohm resistor in series. The switch of the DC supply of 10 Volts, closes at t = 0. Compute the following a. Draw a circuit diagram for t- and t+ b. Compute the time constant c. Plot the Voltage with respect to time, showing the behavior of capacitor charging(take at least 10 values of time in seconds to draw a graph).
The triangular voltage pulse shown below is applied to a 200 mF capacitor. a) Write the expressions thatdescribe vc(t) in the five time intervals t < 0, 0 ≤ t ≤ 2 , 2 ≤ t ≤ 6, 6 ≤ t ≤ 8, and t > 8. b) Derive theexpressions for the capacitor current, power, and energy for the time intervals in part (a).