11. Steam at a pressure of 2MPA and temperature 300°C is passed at a constant rate into a desuperheater unit. The desuperheater is accomplished by continuously spraying water at 95 °C onto incoming superheated steam. The amount of water injected is so regulated that both the water and superheated steam finally change into dry steam at 2 MPa. If the resulting mixture of dry saturated steam leaves the desuperheater at 2MPA and the rate of I kg/s, find the mass of superheated steam used per hour and the mass of water to be injected per hour. Fond also the diameter of the pipe through which the superheated steam flows to the superheater if the speed of the steam through the pipe is not to exceed 25m/s.

11. Steam at a pressure of 2MPA and temperature 300°C is passed at a constant rate into a desuperheater unit. The desuperheater is accomplished by continuously spraying water at 95 °C onto incoming superheated steam. The amount of water injected is so regulated that both the water and superheated steam finally change into dry steam at 2 MPa. If the resulting mixture of dry saturated steam leaves the desuperheater at 2MPA and the rate of I kg/s, find the mass of superheated steam used per hour and the mass of water to be injected per hour. Fond also the diameter of the pipe through which the superheated steam flows to the superheater if the speed of the steam through the pipe is not to exceed 25m/s.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A saturated liquid–vapor mixture of water, called wet steam, in a steam line at 1600 kPa is throttled to 50 kPa and 100°C. What is the quality in the steam line? Use data from the steam tables.
If saturated liquid steam at 850 kPa is throttled to 120 kPa, what is the quality of the resulting steam?
Question 2 Steam flows steadily through an adiabatic turbine. The inlet conditions of the steam are 5 MPa, 600°C, and 90 m/s, and the exit conditions are 50 kPa, 90 percent quality, and 55 m/s. The mass flow rate of the steam is 14 kg/s. Determine: 2.1 The turbine inlet area, and 2.2 The power output in MW.
Hot combustion gases enter the nozzle of a turbojet engine at 260 kPa, 747°C, and 80 m/s, and they exit at a pressure of 85 kPa. Assuming an isentropic efficiency of 92 percent and treating the combustion gases as air, determine the exit temperature.
In an adiabatic turbine, this steam flow is 50 kg / s. The power produced by the turbine is 29 MW.Steam enters the turbine with a pressure of 50 bar and a speed of 60 m / s. At the outlet, at a pressure of 0.06 barIt comes out as saturated water with a speed of 130 m / s. Accordingly, the heat lost by the turbine andFind the turbine inlet and outlet temperatures of steam
Refrigerant-134a enters the coils of the evaporator of a refrigeration system as a saturated liquid–vapor mixture at a pressure of 140 kPa. The refrigerant absorbs 180 kJ of heat from the cooled space, which is maintained at –10°C, and leaves as saturated vapor at the same pressure. Determine the entropy change of the refrigerant.
Water vapor enters a continuous flow adiabatic turbine at a pressure of 25 mPa and a temperature of 700 degrees. It comes out as saturated steam at 50 kPa pressure. Calculate the required mass flow to produce 13 mW of power, ignoring kinetic and potential energy changes.A)8.8 kg/sB)11.5 kg/sC)14.8 kg/sD)3.8 kg/sE)5.5 kg/s
Hot combustion gases enter the nozzle of a turbojet engine at 260 kPa, 747°C, and 80 m/s, and they exit at a pressure of 85 kPa. Assuming an isentropic efficiency of 92 percent and treating the combustion gases as air, determine the exit velocity.
In a certain geothermal area, studies show that 1,500,500 kg/hr of pressurized ground water is available at 2500 psia and 6200F. The water will be throttled to 250 psia to produce ert steam and this mixture will be passed through a water separator to remove the water droplets so that saturated steam at 250 psia is available at the entrance of steam turbine for the proposed power plant. Other data are as follows: Discharge pressure of turbine 25 in. Hg. Vaccum Turbine Engine efficiency 75% Mechanical Loss1.5% of shaft power Generator efficiency 97% Assume atmospheric pressure to be 30 in. Hg. Determine the maximum amount of power in kW that the plant can generate.
Refrigerant-134a enters the coils of the evaporator of a refrigeration system as a saturated liquid–vapor mixture at a pressure of 140 kPa. The refrigerant absorbs 180 kJ of heat from the cooled space, which is maintained at –10°C, and leaves as saturated vapor at the same pressure. Determine the total entropy change for this process.
What is the total entropy change to expand water at 30 psia and 70 percent quality to 10 psia in a closed system undergoing an isothermal, reversible process while exchanging heat with an energy reservoir at 350°F? Use data from tables.
Air with mass flow rate of 1 kg/s enters the first stage of a compressor at 100 kPa and 300 K and exit the second stage of the compressor at 2677 kPa. If the compressed air outgoing from the first stage of the compressor passes through an intercooler, then enters the second stage of the compressor at temperature 353 K. What is the indicated isothermal efficiency for the compressor assuming ideal compression process with polytropica index n = 1.3 for both stages, no pressure loss in the intercooler, and the pressure ratio across the first and the second stage of the compressor are equal?