11.1 Two steel plates with S, = 50 ksi are attached by transverse-loaded fillet welds, as shown in Figure P11.1. Each weld is 4 in. long. E60 series welding rods are used, and good welding practice is followed. What minimum leg length must be used if a force of 33,000 lb is to be applied with a safety factor of 3.0? B F = 33,000 lb FIGURE P11.1 D F = 33,000 lb E60 series welding rods S, = 50 ksi (plates) SF = 3.0 Note: There are two 4 in. welds.

11.1 Two steel plates with S, = 50 ksi are attached by transverse-loaded fillet welds, as shown in Figure P11.1. Each weld is 4 in. long. E60 series welding rods are used, and good welding practice is followed. What minimum leg length must be used if a force of 33,000 lb is to be applied with a safety factor of 3.0? B F = 33,000 lb FIGURE P11.1 D F = 33,000 lb E60 series welding rods S, = 50 ksi (plates) SF = 3.0 Note: There are two 4 in. welds.

Welding: Principles and Applications (MindTap Course List)

8th Edition

ISBN:9781305494695

Author:Larry Jeffus

Publisher:Larry Jeffus

Chapter13: Flux Cored Arc Welding

Section: Chapter Questions

Problem 12R: What is the maximum plate thickness that an FCS weld can be made with 100% penetration without...

See similar textbooks

Similar questions

A GTAW operation is performed on low carbon steel, whose unit melting energy is 10.3 J/mm3. The welding voltage is 22 volts and the current is 135 amps. The heat transfer factor is 0.7 and the melting factor is 0.65. If filler metal wire of 3.5 mm diameter is added to the operation, the final weld bead is composed of 60% volume of filler and 40% volume base metal. If the travel speed in the operation is 5 mm/sec, determine (a) cross-sectional area of the weld bead, and (b) the feed rate (mm/sec) at which the filler wire must be supplied.
An angle iron made of AISI 1040 CD steel is welded to metal as shown and loaded with a dynamic load varying between +40kN and +60kN. E70XX (Sut = 482MPa, Sy = 393MPa) will be used as the welding electrode. Find the factor of safety of the weld zone. Note: that both static and dynamic loads are applied to the source.
A bracket to be welded into a steel channel using E-60 electrode 345 Mpa) Two welding sets are suggested as shown in Fig. (1)Based on maximum shear stress failure theory and safety factor of (2.5) (a) Find the weld size for each set. (b) Which set would you recommend A or B ?
An RSW operation is used to join two pieces of sheet steel having a unit melting energy of 8369.85 J/cm3. The sheet steel has a thickness of 0.3125 cm. The weld duration will be set at 0.25 sec with a current of 11,000 amp. Based on the electrode diameter, the weld nugget will have a diameter of 0.75 cm. Experience has shown that 40% of the supplied heat melts the nugget and the rest is dissipated by the metal. If the electrical resistance between the surfaces is 130 micro-ohms, what is the thickness of the weld nugget assuming it has a uniform thickness?
Assume that two 1.5-mm thick steel sheets are being spot welded at a current of 4000 A and current-flow time is 0.3 s. Using electrodes 5 mm in diameter, estimate the amount of heat generated and the amount of heat required to melt the weld nugget. Use an effective resistance of 350 un. Take u= 9,7 Joule/mm Which one of the following are correct? O a. If the electrodes were 7 mm diameter, the amount of heat generated would decrease b. The amount of heat generated by the equipment is between 1600 to 1700 Joules c. The equipment has enough power to weld the steel sheets. d. The equipment does not have enough power to weld the steel sheets e. The amount of heat required is between 700 and 750 Joules
A mild steel ammonia receiver is a cylinder 2 m in diameter with a pressure load of 1250 kPa and a design stress of 65 MPa. The lap welding tensile strength is 450 MPa and the weld -joint efficiency is assumed to be 100%. Compute the bursting pressure of the receiver in kN/m².
Does all of the heat produced by an SMA weld stay in the weld? Why or why not?
When estimating weld cost, what weld joint design factors should be considered?
How is the E7018 molten weld pool protected?
What is the maximum plate thickness that an FCS weld can be made with 100% penetration without beveling the joint?
Sketch 2 NDT symbols illustrating different methods that can be used to indicate multiple test requirments for the same section of weld.
The welding parameters to be used to butt weld a metal alloy are being evaluated. In order to set up the welding machine, the melting factor for the metal (f2) has to be determined. The welding machine can deliver 4000 watts of power and the heat transfer factor for the welding process (f1) is 0.9. The final weld bead consists of 8 0% filler metal and 40% parent metal. The melting temperature of the filler metal and the parent metal is the same 2540 deg F. The cross-sectional area of the weld bead is 0.5 sq inches. The rate at which filler metal is added to the weld is 1 cu inch per min. Conversion factor 1 Btu = 1055 J and 0 deg F = 460 deg R Calculate the melting factor.