Figure 30 mm 250 mm 30 mm 200 mm W -25 mm V B 1 of 1 Part A If the wide-flange beam is subjected to a shear of V = 31 kN, determine the maximum shear stress in the beam. Set w = 200 mm. (Figure 1) Express your answer to three significant figures and include the appropriate units. Tmax= Submit Provide Feedback OL HÅ Value 3 Request Answer Units ?

Figure 30 mm 250 mm 30 mm 200 mm W -25 mm V B 1 of 1 Part A If the wide-flange beam is subjected to a shear of V = 31 kN, determine the maximum shear stress in the beam. Set w = 200 mm. (Figure 1) Express your answer to three significant figures and include the appropriate units. Tmax= Submit Provide Feedback OL HÅ Value 3 Request Answer Units ?

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.9.4P: A circular pole is subjected to linearly varying distributed force with maximum intensity t0....

See similar textbooks

Similar questions

A thin-walled aluminum tube of rectangular cross section (sec fig me) has a centerline dimensions b = 6.0 in. and b = 4.0 in. The wall thickness t is constant and equal to 0.25 in. Determine the shear stress in the tube due to a torque T = 15 kip-in. Determine the angle of twist (in degrees) if the length L of the tube is 50 in. and the shear modulus G is 4.0 x 106 psi.
A two-axle carriage that is part of an over head traveling crane in a testing laboratory moves slowly across a simple beam AB (sec figure). The load transmitted to the beam from the front axle is 2200 lb and from the rear axle is 3800 lb. The weight of the beam itself may be disregarded. Determine the minimum required section modulus S for the beam if the allowable bending stress is 17,0 ksi, the length of the beam is 18 ft, and the wheelbase of the carriage is 5 ft. Select the most economical I-beam (S shape) from Table F-2(a), Appendix F.
A square tube section has side dimension of 20 in. arid thickness of 0.5 in. If the section is used for a 10-ft-long beam subjected to 1250 kip-in, torque at both ends, calculate the maximum shear stress and the angle of twist between the ends. Use G = 11,600 ksi.
A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?
A circular pole is subjected to linearly varying distributed force with maximum intensity t0. Calculate the diameter daof the pole if the maximum allowable shear stress for the pole is 75 M Pa.
A simple beam with a W 10 x 30 wide-flange cross section supports a uniform load of intensity q = 3.0 kips/ft on a span of length L = 12 ft (sec figure). The dimensions of the cross section are q = 10.5 in., b = 5.81 in., t1= 0.510 in., and fw = 0.300 in. Calculate the maximum shear stress tjuly on cross section A—A located at distance d = 2.5 ft from the end of the beam. Calculate the shear stress rat point Bon the cross section. Point B is located at a distance a = 1.5 in. from the edge of the lower flange.
A machine shaft supported on bearings 2 m apart is to transmit 180 KW at 200 rpm while subjected to a reversed bending load of 5000 N located at a distance of 60 cm from one bearing. Allow a shear stress of 40 MPa and a bending stress of 80 MPa, determine the shaft diameter for steady loading if km = 1.5 and ks = 1.0. note: answer must be in mm
E 4G 1:09 1 0 K/s ۲ نیسان، ۲۰۲۱ :) > ۱۱:۲۶ ص اسئلة مقاومة المواد 0-1 The gears attached to the fixed-end steel shaft are subjected to the torques shown in fig. The shaft has diameter of (14 mm ).Determine the max shear stress and the angle of twist A relative c . use G=80 Gpa A 280 N.m 150 N.m B c 40 N.m ) ) 43 0.4m 0.3m Q-2 Draw the shear and moment diagram for the beam loaded shown in fig 15 KN 80 KN .m 5 KN/m B 5 m 5m ū
A propeller shaft is required to transmit 45 kW power at 500 rpm. It is a hollow shaft having inside diameter 0.6 times the outer diameter. It is made of plain carbon steel and the permissible shear stress is 84 N/mm^2. Determine the inner and outer diameters of the shaft.
What is the maximum normal stress, MPa, due to bending on section a-a? For W310x52, S = 748µm^3. Answer in whole numbers, no units. (Example: 123MPa --> 123)
A 5-mm thicc plate of steel is formed into the cross section shown in Fig. P8.13. Locate the shear center for the cross section. e Figure P13
A section of a rotating shaft is under an alternating bending moment of 70Nm and a torque of 35Nm. The yield strength of the material is 560 MPa and the ultimate tensile strength of the material is 700 MPa. The estimated actual endurance strength is assumed to be 210 MPa and the stress concentration factor is 1.5 for well rounded fillet. (Design Factor = 2) Determine the minimum diameter of the section of the shaft: D = mm