11.5 Derive Hagen-Poiseuille equation for a steady viscous flow in a horizontal pipe with a diameter of ro. The fluid is incompressible with a constant viscosity. Assume one dimensional flow and constant pressure gradient Hint: start with the continuity equation and the Navier-Stokes equation in the cylindrical coordinates, which is:

11.5 Derive Hagen-Poiseuille equation for a steady viscous flow in a horizontal pipe with a diameter of ro. The fluid is incompressible with a constant viscosity. Assume one dimensional flow and constant pressure gradient Hint: start with the continuity equation and the Navier-Stokes equation in the cylindrical coordinates, which is:

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Find the type of flow based on the Reynold's Number for a fluid of sp.gr 0.8 which is flowing in the flow channel of diameter 300mm, velocity of flow is 1000m/s and dynamic viscosity of 17.6poise
I6 a) Determine the radial positions of a pitot tube for a 6-point traverse in a 0.3 m inner diameter pipe. Show your calculations. b) If the fluid velocity measured at the pipe center is 0.3 m/s and yields a Reynolds number based on local velocity of 4000, what is the fluid cross-sectional average velocity in the pipe? c) At what value of Re is the discharge coefficient of an orifice meter approximately independent of geometry and flow rate?
Water with a dynamic viscosity of 0.892 cP flows in a smooth pipe of diameter, D = 50 mm and length, L = 10 m. The cross-sectional mean velocity is 1.50 m/s. What type of flow is observed? Calculate the discharge, the entrance length and the friction coefficient. Please solve according to question... I need all answers... Thank you
In a pipe of diameter 300mm the center line velocity and the velocity at a point 100mm from the center, as measured by pitot tube are 2.4 m/s and 2.0 m/s respectively. Assume the flow in the pipe to be turbulent find: 1-Dischrge through the pipe,2-Coefficient of friction, 3 Height of roughness projections.Please do not waste my question solve with correct answers only.
For the flow of 12.9 L/min of water at 75 degrees Celcius in a plastic pipe, 16mm OD x 1.5mm wall, compute the expected maximum velocity of flow. Answer is 1.95m/s. Please show how to solve.
liquid (density 800kg/m3, viscosity 10−3 kg/ms) has to be supplied at a mean speed of 2m/s through a pipe of diameter 12.5mm with a surface roughness equivalent to that for structural steel. What is the magnitude of the pressure gradient necessary to achieve this flow? Your answer should have a positive sign and be to the nearest 10 Pa/m. You may wish to use the Moody diagram.
Subject : Fluid mechanics Read the question carefully and give me right solution according to the question. Two pipes with C1 = 120, connected in series, discharge 4.75 cfs with a loss of head of 27 ft. Each pipe has a length of 1000 ft. If one pipe has a diameter of 18 inches, determine the diameter of the other pipe. Neglect minor losses. Note: Diagram not given
What is the Reynold’s number for a flow of oil (SG = 0.80, ? = 0.00200 lb-s/ft2) in a 6-in diameter pipe at a flow rate of 10ft3/s. Is the flow laminar or turbulent? thank you!
A fluid flow is given by V = 8x³ i - 10xy j Find the shear strain rate and state whether the flow is rotational or irrotational.
Find the type of flow based on the Reynold's Number for a fluid of sp.gr 0.8 which is flowing in the flow channel of diameter 300mm, velocity of flow is 1000m/s and dynamic viscosity of 17.6poise. Write short notes on Non Uniform flow with e quations
Find the head lost due to friction in a pipe of radius 20 cm and length 50m, through which oil is flowing at a velocity of 5 m/s using (a) Darcy formula (b) Chezy formula for which C= 65, Take Specific gravity of the oil is 0.8 and Dynamic viscosity is 8 X 10-3 poise.
A service truck transfers hydraulic oil with a kinematic viscosity of 200 cSt through a 2-in. I.D. hose 100 ft. long to a bulldozer at a flow rate of 50 gal/min. What is the pressure drop between the service truck and the bulldozer if the fluid Sg is 0.85?