12. A constant diameter pipeline is used to transfer water from one location to location. At outlet, pressure is 5 bar and inlet is 1 bar. Neglecting elevation difference, determine all the surviving terms of the energy equation. UM 13. Siphoning mechanism is used to transfer water from the tank using a pipe with a diameter of 2 cm and then discharged into atmosphere. Total head loss from A to C is 0.2 m and C to B is 0.4 m. h₂ = 1 m and h₂ = 2 m. Determine, a) the flow rate in the hose b) pressure at point C c) if puncture develops at point C, will water leak out of the hose, or will air leak into or nothing will Q Search

12. A constant diameter pipeline is used to transfer water from one location to location. At outlet, pressure is 5 bar and inlet is 1 bar. Neglecting elevation difference, determine all the surviving terms of the energy equation. UM 13. Siphoning mechanism is used to transfer water from the tank using a pipe with a diameter of 2 cm and then discharged into atmosphere. Total head loss from A to C is 0.2 m and C to B is 0.4 m. h₂ = 1 m and h₂ = 2 m. Determine, a) the flow rate in the hose b) pressure at point C c) if puncture develops at point C, will water leak out of the hose, or will air leak into or nothing will Q Search

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter10: Heat Exchangers

Section: Chapter Questions

Problem 10.19P

See similar textbooks

Similar questions

A centrifugal pump has the following characteristics as shown in Table 1. Table 1: Pump characteristics Q(m3 /s) 0.033 0.029 0.027 0.0235 0.020 0.017 0.0133 H(m) 40 60 66 75 80 84 90 Efficiency % 20 45 55 68 75 66 45 The pump is used to pump water from a low reservoir to a high reservoir through a total length of 1100 m of pipe 250 mm in diameter. The difference between the water levels in the reservoirs is 25 m. Neglecting all losses except friction and assuming λ=0.042, calculate: i. The discharge and head at the duty point for the pump. (20) ii. The efficiency at the duty point. (5) [2
A pump draws water from open reservoir A at 20 ft above pump centerline and lifts to an open reservoir B at 280 ft above pump centerline. The loss of head at the suction is 3 times the velocity head at the 6 inches suction pipe and at the discharge is 20 times the velocity head at the 4 inches discharge pipe. The pump discharge is 200 GPM. a. The total dynamic head in ft. 268.32 367.62 288.32 b. The water power in horsepower 31.49 13.54 19.45
1) Interpret solar power in the context of environmental impact.2. What is the rigid dichotomy between windmill and diesel-driven pumps?3. For a normal windmill-driven pump at 3 m/s wind speed, the yield at a 10 m Head is typically 0.12 liters/s per m2 of rotor area, value windmills in the context of yield.
A turbine is located at an elevation 200 m below that of the surface of the water intake. The friction loss in the pipeline leading to it is 8 m and the turbine efficiency is 90%. What is the power input delivered by the water to the turbine if the flow is 3.0 m^3/s in kW? CHOICES: a.5650.56 b.5690. 45 c.5050.78 d.5085.50
Air enters a fan through a duct at a velocity of 6.4 m/sec and an inlet static pressure of 2.4 cm of water less than atmospheric pressure. The air leaves the fan through a duct at a velocity of 11.26 m/sec and a discharge static pressure of 7.63 cm of water above the atmospheric pressure. If the specific weight of the air is 1.22 kg/m3 and the fan delivers 9.46 m3/sec, what is the fan efficiency when the power input to the fan is 17.36 KW at the coupling?
Air enters a fan through a duct at a velocity of 6.3 m/s and an inlet static pressure of 2.5 cm of water less than atmospheric pressure. The air leaves the fan through a duct at a velocity of 11.25 m/s and a discharge static pressure of 7.62 cm of water above the atmospheric pressure. If the specific weight of the air is 1.2 kg/m3 and the fan delivers 9.45 m3/s, what is the fan efficiency when the power input is 13.75 kW at the coupling?
A jet engine is bolted to a stationary test stand and run at full thrust. Air enters the engine at a rate of 80lbm/sec and fuel enters the engine at a rate of 0.8 lbm/sec. Additionally, the following values are known:Pinlet = 13 psi Pexhaust = 14.7 psiVinlet = 500 ft/sec Vexhaust = 1500 ft/secAinlet = 4 ft2 Aexhaust = 3 ft2Find the reaction force required to hold the engine in place on the test stand.
A turbine is located at an elevation 200 m below that of the surface of the water intake. The friction loss in the pipeline leading to it is 8 m and the turbine efficiency is 90%. What is the power input delivered by the turbine to the turbine if the flow is 3.0 m^3/s in kW? a.5121.41 b.5690.45 c.5085.50 d.5650.56
Water is being pumped the through one inch diameter piping arrangement to a higher elevation (5 meters up). Assume incompressible fluid conditions and some heat losses to the surroundings. At the inlet water pressure is 1 bar, temperature 15C, and volumetric flow rate is 0.02 m3/s. At the exit pressure is 2.2 bar, temperature is 10C and velocity of the stream is 40 m/s. Determine: a.Density of the inlet stream using NIST tables. b.Mass flow rate [kg/s] c.Determine h2 from known p2 and T2 using NIST tables d.Find heat rate removed from Q=m(h1-h2) Use Energy Balance Equation with enthalpy difference and in the units of kW to find pumping power in kW. NOTE: The heat is removed from the system, so it should be negative in your equation! show all steps please thanks
Water is being pumped the through one inch diameter piping arrangement to a higher elevation (5 meters up). Assume incompressible fluid conditions and some heat losses to the surroundings. At the inlet water pressure is 1 bar, temperature 15C, and volumetric flow rate is 0.02 m3/s. At the exit pressure is 2.2 bar, temperature is 10C and velocity of the stream is 40 m/s. Determine: a.Density of the inlet stream using NIST tables. b.Mass flow rate [kg/s] c.Determine h2 from known p2 and T2 using NIST tables d.Find heat rate removed from Q=m(h1-h2) Use Energy Balance Equation with enthalpy difference and in the units of kW to find pumping power in kW. NOTE: The heat is removed from the system, so it should be negative in your equation! show all steps please
Water is being pumped the through one inch diameter piping arrangement to a higher elevation (5 meters up). Assume incompressible fluid conditions and some heat losses to the surroundings. At the inlet water pressure is 1 bar, temperature 15C, and volumetric flow rate is 0.02 m3/s. At the exit pressure is 2.2 bar, temperature is 10C and velocity of the stream is 40 m/s. Determine: a.Density of the inlet stream using NIST tables. b.Mass flow rate [kg/s] c.Determine h2 from known p2 and T2 using NIST tables d.Find heat rate removed from Q=m(h1-h2) Use Energy Balance Equation with enthalpy difference and in the units of kW to find pumping power in kW. NOTE: The heat is removed from the system, so it should be negative in your equation!
The refrigerant R134a is passing through the diffuser with the inlet diameter of D1=1 inch; p1=150psi; and V1=1000 ft/s as a saturated vapor. The exit parameters are p2=400 psi, and velocity V2=0.5 ft/s. Heat transfer, Work, and Potential energy changes can be neglected. NOTE: Use English units. For the kinetic energy change do not forget dividing to (778*32.2) conversion factor to obtain Btu/lbm. From NIST tables use BTU/lbm units for the enthalpy. Determine: a.Exit temperature in F; b.Mass flow rate in lbm/s; c.Exit diameter D2 in inches. d.Determine exit temperature. show and expalin each step please