13-30. The rib-joint pliers are used to grip the smoothpipe C. If the force of 100 N is applied to the handles,determine the state of stress at points A and B on the crosssection of the jaw at section a-a. Indicate the results on anelement at each point.100N-250 mm-25 mm25 mm10 mm20 mm|100NSection a-a

The pliers is an assembly of two components.

Answered: 13-30. The rib-joint pliers are used to…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The rib-joint pliers are used to grip the smooth pipe C. If the force of 100 N is applied to the handles, determine the state of stress at points A and B on the cross section of the jaw at section a–a. Indicate the results on anelement at each point.
10-1. The 500-kg engine is suspended from the jib crane at the position shown. Point B is just above the bottomflange. Determine the state of stress at point B on the cross section of the boom at section a–a. Please include a free body diagram.
The short concrete cylinder having a diameter of 50 mm is subjected to a torque of 500 N # m and an axial compressive force of 2 kN. Determine if it fails according to the maximum normal stress theory. The ultimate stress of the concrete is sult = 28 MPa.
The assembly is used to support the distributed load of w=500 lb/ft. determine effortnormal in bar BC and the shear stress in pins B and C. The bar has adiameter of 0.40 in. and each of the bolts has a diameter of 0.30 in. Express theanswers in ksi.
If each of the three nails has a diameter of 4 mm and can withstand average shear stress of 60 MPa, determine the maximum allowable force P that can be applied to the board.
The A-36 steel pipe has a 6061-T6 aluminum core. It is subjected to a tensile force of 200 kN. Determine the average normal stress in the aluminum and the steel due to this loading. The pipe has an outer diameter of 80 mm andan inner diameter of 70 mm.
The bellcrank is in equilibrium a) determine the diameter of the bar DE if the normal stress is limited to 100MN/m2.b) Determine the diameter of the pin located at C if the shear stress is limited to 70 MN/m2.c) Determine the crushing force in the support plates in C with a thickness of 6mm.
The small-block has a thickness of 0.5 in. If the stress distribution at the support developed by the load varies as shown, determine the force F applied to the block, and the distance d to where it is applied.
The bolt has a diameter of 20 (mm) and passes through a tube that has an inner diameter of 50 (mm) and an outer diameter of 60 (mm). If the bolt and tube are made of A-36 steel, determine the normal stress in the tube and bolt when a force of 40 (kN) is applied to the bolt. Assume the end caps are rigid.
Determine the normal stress and shear stress acting on the inclined plane AB. Solve the problem using the method of equilibrium described in Sec.
The spreader bar is used to lift the 2000-lb tank. Determine the state of stress at points A and B, and indicate the results on a differential volume element.
The collar has a mass of 5 kg and falls down the titanium Ti-6A1-4V bar. If the bar has a diameter of 20 mm, determine the maximum stress developed in the bar if the weight is (a) dropped from a height of h = 1 m, (b) releasedfrom a height, h 0, and (c) placed slowly on the flange at A.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS