13) A bucket full of water hangs from one end of a string that passes over a light pulley. The other end of the string is driven by an oscillator of constant frequency, and the fundamental mode of standing waves is observed with one loop formed between the oscillator and the pulley. Holes are poked in the bucket causing it to start leaking water. When the bucket's mass drops to 1/4 of its initial value, oscillator oscillator ??? pulley pulley leaking bucket water-filled bucket (m) (m'=m/4) (a) No standing waves are observed on the string (b)A standing wave with two loops is observed (c) A standing wave with three loops is observed (d)A standing wave with four loops is observed

13) A bucket full of water hangs from one end of a string that passes over a light pulley. The other end of the string is driven by an oscillator of constant frequency, and the fundamental mode of standing waves is observed with one loop formed between the oscillator and the pulley. Holes are poked in the bucket causing it to start leaking water. When the bucket's mass drops to 1/4 of its initial value, oscillator oscillator ??? pulley pulley leaking bucket water-filled bucket (m) (m'=m/4) (a) No standing waves are observed on the string (b)A standing wave with two loops is observed (c) A standing wave with three loops is observed (d)A standing wave with four loops is observed

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A farmer has a pump which discharges 100 lpm of water at a head of 10 m. The pump is driven by anelectric motor at speed of 1700 rpm through 4”x 4” pulley-drive combination for the motor and thepump, respectively, what would be the pump output if the motor pulley is changed to six inchesdiameter?
1. For a given pump, the diameter, the gauge pressures at the inlet and outlet are −30 × 103 P a and 200 × 103 P a, respectively. If the flow rate is 0.1 m3/s, and the power required is 25 kW, find the efficiency. The intake and discharge are at the same height. 2. The impeller of a radial-flow turbine has an outer radius of 4 f t, turning at 200 rpm. The volume flow rate is 1000 ft3/s, and it discharges in the axial direction. Neglect all losses. If the tangential component of the velocity at the inlet is 5 f t/s, find: (a) The torque exerted on the impeller. (b) The power developed by the machine.
a mass stand in floor which execute SHM vertically at 5hz frequency .show that mass losses contact with floor if displacement exceed 1 cm.?
Problem 2Given: A wave of 0.3 m wave height and period 1.3 seconds is generated in a wave tank. The wave tank is 90 m. long, 3 m wide, and 3 m deep and filled with fresh water to a depth of 1.5 m. The density of water is 997 kg/m3. Required:a) Determine the classification of the wave (i.e., shallow, intermediate, deep).b) Evaluate the wave celerity, length, and group celerity.c) Evaluate the energy in one wavelength.
1)A wave with a period T = 10 seconds is propagated shoreward over a uniformly sloping shelf from adepth d = 656 ft to a depth d = 9.8 ft. Find the wave celerities C and lengths L corresponding to depths d =656 ft and d = 9.8 ft 2) A wave in a depth d = 12 m, height H = 3 m, and a period T = 10 sec. The corresponding deepwaterwave height is H0 = 3.13 m.Find:(a) The maximum horizontal and vertical displacement of a water particle from its mean position when z= 0 and z = -d.(b) The maximum water particle displacement at an elevation z = -7.5 m when the wave is in infinitelydeep water.(c) For the deepwater conditions of (b) above, show that the particle displacements are small relative tothe wave height when z = -L0 /2 3)A concrete coated steel gas pipeline is to be laid between two offshore platforms in 100 m water depthwhere the maximum environmental conditions include waves of 20 m wave height and 14 s period. Thepipeline outside diameter is 46 cm, and the clay bottom slope is 1 on…
Assume that annual energy requirement of an industry is 20000 kWh . DETERMINE size of wind turbine that is required to be installed to meet the energy requirement . Following assumptions are taken into account for estimation Annual energy requirement - 20000 kWh Propeller type wind machine is used . Coefficient of performance -0.40 Wind speed at 15 meter height is 5 meter / sec ( if the turbine hub is placed at the height other than 15 meter , the wind speed should be estimated as shown in " vertical wind speed variation section Density of air - 1 kg / m Capacity factor -0.30
Compare the apparent frequencies of a 2550 Hz source moving away from you at 25 m/s and when you are moving away from the source at 25 m/s. Assume of 30 degrees Celsius.
Problem 15.6 Solve the given problem: A Laser doppler velocimeter was used to determine the velocity of the water flow in an open channel whose cross section is a triangle with a base of 0.532 m and a depth of 0.444 m. If the velocity of the water flow is 8.97 m/s, determine the mass flow rate in kg/s
A wave of period 10 s is propagating toward a rubble mound breakwater in water of constant depth h = 30 m. A pressure gage located at 10 m from the bottom in front of the breakwater shows a time record with an envelope beating between minima of amplitude 2,100 N/m2 and maxima of amplitude 4; 700 N/m2. Calculate the rate (per meter of width) at which energy is dissipated by the breakwater. At what separation distance do the pressure maxima occur?
PROPAGATION OF ERROR You are tasked to supervise the design of 0.5MW wind turbine to be constructed in a Wind Farm in Pililla, Rizal. Suppose the design criteria are as follows: The air density as surveyed after 2 year period averaged at 1.225 kg / cubic meter. The sweeping diameter of the rotor blades is 125m, and the anemometer reading in the area amounts to 4.2m/s on a 2 year period of survey. What is the theoretical power output of the turbine assuming 100% efficiency of operation? Your answer must be in kW and in two decimal places with correct signs. In the previous problem, if the diameter measurement is off by 0.1m and the anemometer reading is also fluctuating by 0.05m/s and if the error measurement for theoretical power output must be limited to 3%, WHY OR WHY NOT should you accept the design? * Show complete solution in paper.
please answer A pump impeller rotating at 1400 rpm has an outside radius of 21 cm, the vane outlet angle β2 is 158° and the radial velocity at the outlet Cr2 is 4 m/s. Assuming radial flow at inlet, draw the theoretical outlet velocity diagram and calculate the various velocities and angles.( A)What is the theoretical head Ho, in meters, assuming that the circulatory flow coefficient η∞ = 1.,(B)In the preceding example; assume a deviation of 10° applied to β2 due to circulation after the modern theory. The flow is 30 lit/s. After drawing/illustrating the velocity diagram, find the theoretical head Ho, in meters, assuming radial flow at inlet, neglecting the deviation in inlet velocity diagram. (c)Assuming that the mechanical efficiency ηmech = 0.95, the hydraulic (or manometric) efficiency ηman = 0.8, find the required break horsepower to drive the pump.
1. You are tasked to supervise the design of 0.5MW wind turbine to be constructed in a Wind Farm in Pililla, Rizal. Suppose the design criteria are as follows: The air density as surveyed after 2 year period averaged at 1.225 kg / cubic meter. The sweeping diameter of the rotor blades is 125m, and the anemometer reading in the area amounts to 4.2m/s on a 2 year period of survey. In the design specifications given, if the actual measurement of power via the substation amounts to exactly 530kW and given that the windspeed is off by 0.05m/s, what could have been the error in the measurement of diameter? Your answer must be in 3 decimal places and in correct signs and measurement. Show complete solution in paper.