13. A 25 kVA, 3-phase, Y-connected, 400 V synchronous generator has a synchronous impedance of 0.05 + j1.6 2 per phase. Determine the full-load voltage regulation at 0.8 power factor lagging. a. 10.6% b. 5.5% C. 22.2% d. 25%

13. A 25 kVA, 3-phase, Y-connected, 400 V synchronous generator has a synchronous impedance of 0.05 + j1.6 2 per phase. Determine the full-load voltage regulation at 0.8 power factor lagging. a. 10.6% b. 5.5% C. 22.2% d. 25%

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.41P

See similar textbooks

Related questions

Q: Calculate the value of RC in ohms. at VCC=18 V, IB=23 uA, and VC=7V and B=52

A: Given: Vcc=18 vIB=23 μAVC=7 and β=52 Calculation of RC in the given circuit :

Q: A. Write the correctresistance and tolerance of the color bond resistors. Resistor Color Bond Resist...

Q: 7. A long - shunt compound generator delivers a load current of 50A at 500V and has armature, series...

A: The solution is given below

Q: What quantity of charge must be delivered by a battery with a potential difference of 100 V to do 50...

A: Given: Potential difference, V = 100 V Energy, W = 500 J

Q: 1. What is the barrier potential of a silicon diode when the temperature is 100°C. ANS. Vf = 0.55V 2...

A: Given, Two problems with answer. We have to find the steps and write. Please find the below attachme...

Q: A poor conductor is characterized by a conductivity 200 (S/m) and permittivity € = 460. At what angu...

A: We need to find out angular frequency for given condition

Q: R: = 60 R = 45 Re= 1025 12 V R = 80 Rg = 60 REa R2 = 8n Ri = 20 Rs = 60 R = 40 R; = 8n Figure 12

Q: 3-IS there a relationship between splicing losses and bending losses if we take into consideration t...

A: Splicing Loss: Splice loss refers to the part of the optical power that is not transmitted through ...

Q: (a) Find both wattmeter readings in Fig. 12.39 if VA = 100/0" V rms, VB = 50/90° V rms, ZA = 10 – j1...

A: The circuit diagram is shown below, Here,VA=100∠0° VVB=50∠90° VZA=10-j10 ΩZB=8+j6 ΩZC=30+j10 Ω

Q: b) Obtain the Fourier series coefficient of the signal x[n] shown in Figure Q3(b). x[n] 3 4 Figure Q...

Q: Advantages and disadvantages of DIGIT IC

A: Brief description : Digital integrated circuits are one of the major advantage on the analog discret...

Q: An overhead line 50 kms in length is to be constructed of conductors 2.56 cm in diameter for 50 Hz s...

A: Given data: An overhead line has, Length, l = 50 km Diameter, d = 2.56 cm = 0.0256 m Radius, r = 0....

Q: 1. In the linear transformer circuit below, calculate the ff: a. Input impedance b. Current in prima...

A: According to Bartley policy, only 3 question is to be attempted but as these questions are interlink...

Q: 1. Importance of studying earth resistance and resistivity. 2. Importance of bringing the earth resi...

A: Given, About the earth resistance.

Q: Given: Pt. Q (2,-3,6) and Pt. R(3, 0, -6) Solve for the following: a. Displacement vector (d1) from ...

Q: Power factor adjustment minimizes. power in the circuit, allowing the large percentage of the power ...

Q: A 3-phase generator connected in wye has the following characteristics: Eo = reactance Xs = 1442, li...

A: The solution is given below

Q: 520 V 16 N 260 N 1 A 40 Ω Vo 250 N 6Ω Using superposition to get the Thevenin voltage (in volts) see...

Q: How much energy is required to move 5C of charge from one point in a circuit to another when the vol...

Q: Calculate the required R1 in ohms RC=1920 ohms, IB=23 uA, VC=9V, R2=6916 ohms, RE=282 ohms and B=13...

Q: Problem 1 Using a map, determine the Boolean expression in Product-of-Sums (POS) form of the functio...

A: In this question, We need to determine the boolean expression in the POS form. We know Maxterm ce...

Q: what is the total resistance of the circuit if R1= 10Ω R2=5Ω R3=5

Q: 9. A 250 V DC long-shunt, compound motor takes a current of 82 A at full load. Calculate the motor e...

Q: Using superposition to get the Thevenin voltage (in volts) seen by the 250Q resistor, what is the co...

Q: 玩, 1 /3 早2 画Q 180% R4 Search 'Crop Page" PO Export PDF DE Edit PDF 3) The ECG Lead III signal is det...

A: OPERATIONAL AMPLIFER: An operational amplifier is an integrated circuit that can amplify weak elect...

Q: 5 Kilo bytes is equivalent to nibbles.

A: Converting Kilo bytes into nibbles

Q: Convert the following from rectangular to polar form: a) 10 + j10 b) 5 – j10 1) a) b)

A: Brief description : In the given question they want to know the polar form of rectangular functions....

Q: Collector characteristics for the Ge transistor If VEE =2 V, VCC =12V, and RC = 2k , size RE so that...

A: For a Ge transistor - VEE=2VVCC=12VRC=2kΩVCEQ=6.4 V

Q: Problem 2: A stationary loop of conducting wire, located on the x-y plane, is in the presence of the...

Q: Determine the Q-point and find the maximum peak value of the base current for linear operation. Assu...

A: The given transistor is shown below: The Q point of the above transistor is given by the expressio...

Q: Characteristics of Digital IC

A: Characteristics of Digital IC 1. Fan out2. Dissipation in power3. Delay in propagation4. Noise thres...

Q: 6. A 6-pole DC generator with duplex lap winding has 48 slots and four elements per slot. The flux p...

A: Given, In a DC generator Poles, P=6 Duplex lap winding with 48 slots and four elements per pole. Flu...

Q: b) An engineer investigates the speed of motor, o(s) for excited de motor in Question 1(a). She cont...

A: Answer-

Q: T20 V v 4 O 4A O 1A O 5A O 3A

A: Norton'theorem: A two-terminal network containing linear and bidirectional elements and independent ...

Q: А. Suppose we replace the source vj with a DC voltage VI in series with a small time-varying voltage...

A: The circuit is given as iA=c2vA2+c1vA+c0-----1vA=vI-RiAvA=vi+VI-RiAVA+va=vi+VI-Ria+IA-----2

Q: Vcc RB RC Q1 NPN +88.8 RE Volts VE

A: We need to find Vcc for given circuit .

Q: t = 0 R=10 Q L=1 H v=20e-2t + C=1 µF i

Q: 4.Find the gain vo/vs of the circuit shown below 10K O 10KO Vs Vo 20kQ

Q: 11011.0101- 1101.0 11

A: 10 -1=1; 2-1= 1 100-001=11; 4-1=3 100-10=10 ; 4-2=2

Q: Power factor correction is usually done by adding _________ to the load circuit.

A: This question belongs to circuit theory . It is based on the concept of power factor improvement in ...

Q: Calculate the base current IB in uA when VCC=16V, VEE=-16V , RB=9205 ohm, RC=12529ohm, RE=11879ohm ...

Q: B. Study the usage of breadboard in electronics. Given the symbol of resistor as difference (battery...

A: Usage of breadboard and schematic diagram of circuit connection in breadboard:

Q: VI) For the circuit shown, answer the questions from 15-19. The load Zt = 8+j6 ohms, and the source ...

Q: j52 50260° v j20 n j40 2 l

A: Resistors, inductors and capacitors form an integral part of any electrical circuit. A source, eithe...

Q: 0. (8 points) Builda cireuit (with the minimal number of gates) that generates a parity bit for its ...

A: Priority encoder is another form of the encoder, the encoder has 2n input and n output Select lines...

Q: QUESTION 13 How many power consuming outlets may be installed on a 30 A, 120 V branch circuit in a c...

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any ...

Q: 56. Determine Ig and Vc for the network of Fig. 4.152. +8 V 3.3 k2 B = 110 3.9 k2 o-12 V Vc

Q: e.) Find the voltage output V.(t) of this circuit with the given values: Voltage input Vin = sin(2n ...

A: Capacitors and inductors are the energy storage elements which store the energy while operation. Cur...

Q: 8. The armature and shunt field resistance of a 50-kW, 220 V shunt generator is 0.026 ohm and 52 ohm...

Q: Vcc R1 RC Q1 NPN +88 8 R2 RE Volts VC

Concept explainers

Synchronous Generator

In comparison to an asynchronous generator, it is a machine where the rotor speed is equal to the rotating magnetic field produced by the stator, i.e., mechanical speed is equal to the electrical speed, thus called synchronous, and not asynchronous.

Salient Pole Rotor

Salient pole rotor includes a large number of exposed poles mounted on a magnetic wheel. The construction of a bright pole is as shown in the image on the left. The proposed poles are made of metal laminations. The rotor winding is provided on these poles and is supported by pole shoes.

Question

13. A 25 kVA, 3-phase, Y-connected, 400 V synchronous generator has a synchronous impedance of
0.05 + j1.6 2 per phase. Determine the full-load voltage regulation at 0.8 power factor lagging.
a. 10.6%
b. 5.5%
c. 22.2%
d. 25%

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A generator rated 1MVA, 13.8 kV 60 hz 3-phase wye connected, 6-poles has 19Ω synchronous reactance per phase and negligible resistance. The field copper loss and SPL are 15 kW and 30 kW respectively. Determine the % VR and efficiency of the generator at rated load and unity power factor
A 3-Phase 10Kva, 400 V, 50Hz star connected alternator supplies a rated load at 0.8 power factor lagging. If the armature resistance per phase is 0.5Ჲ and the synchronous reactance is 10Ჲ, using the e.m.f method, estimate the alternator’s voltage regulation
A3 phase , 15 kV, 60 Hz, 30 MVA, Y-connected cylindrical-rotor synchronous machine generator has Ra =0.5 Ω per phase and Xs =5.2 Ω per phase. The generator delivers the rated load at 15 kV and 0.85 lagging power factor. Determine the excitation voltage, Ef, for this operating condition.
When this generator is connected to a 13.8 kV distribution feeder of negligible impedanceand operates at an output power of 8.75 MW at 0.9 power factor lagging, work out the field current, the reactive-power output, and the load angle for this operating condition.
A three-phase wye-connected wound rotor synchronous generator rated at 10 KVA, 230 v has synchronous reactance of 1.2 ohms per phase and armature resistance of 0.5 ohm per phase. What is the power factor such that the voltage regulation at full-load is zero?
A 760-kVA, 2300-V, three-phase, Y-connected, synchronous generator is operated at its rated speed to obtain its rated no-load voltage. Later, another test finds that the short-circuit phase current is 128A. The average resistance of each phase is 0.56 ohm. 1) Determine the synchronous reactance per phase. 2) Determine the voltage regulation when the generator delivers the rated load at its rated voltage and 0.75 PF lagging.
The effective resistance of a 2200 V, 50 Hz, 440 KVA, 1 -phase alternator is 0.5 ohm. On short-circuit, a field current of 40 A gives the full load current of 200 AS. The electromotive force on open-circuits with same field excitation is 1160 V. Then the synchronous impedance and reactance is _______ ohm and _______ ohm respectively.
An 11 kV, three-phase, turbo alternator has a synchronous impedance per phase of(0,4 + j0,8) Ω and it supplies 2 kA at unity power factor to an infinite bus. Theexcitation is increased so that the emf is increased by 20%. Sketch a general loaddiagram and determine the following from this diagram: the armature current for maximum power output, the actual maximum power output
A 3-phase, 11-kVA, 10-MW, Y-connected synchronous generator has synchronous impedance of (j 8.0) Ω/ph. If the excitation is such that the open circuit voltage is 14 kV, determine (i) the maximum output of the generator (ii) the current and p.f. at the maximum output & (iii) the voltage regulation Please answer all subpart please try in typing format please
A 3-phase, Y-connected, 60 Hz, 6 MVA, 13.2kV synchronous generator has a synchronous reactance of 0.9 ohms and negligible resistance. It supplies a constant power load at rated conditions at 0.83 pf lagging. At the load, the line current lags the line-to-neutral voltage by how many degrees?
The armature resistance and synchronous reactance of a 2 kV, 3-phase, wye-connected synchronous motor is 0.2 ohm and 2.2 ohms respectively. The power input is 800 kW at normal voltage and the generated line emf is 2500 V. Determine the line current and power factor.
2.2 A three-phase synchronous generator has a reactance of 1.5 p.. and negligible resistance. It supplies a rated current of 1.0 p.. at 1.0 p.u. terminal voltage to a lagging load of 0.9 power factor. Determine the rated excitation voltage in p.u. and the internal load angle. Construct the performance chart of the generator in 2.1 (above) assuming its rating is 450 MVA.