#13 AP Physics 1 question attached. Questions 12-14 refer to the following material.1.0 m1.0 m1.5 mA cylinder at rest is released from the top of aramp, as shown above. The ramp is 1.0 m high, andthe cylinder rolls down the ramp without slipping. Atthe bottom of the ramp, the cylinder makes a smoothtransition to a small section of a horizontal table andthen travels over the edge at a height of 1.0 m abovethe floor, eventually landing on the floor at ahorizontal distance of 1.5 m from the table. 13. After the cylinder leaves the table, but before itlands, how do the rotational kinetic energy andenergy of the cylindertransłational kineticchange, if at all?RotationalTranslationalKinetic EnergyKinetic Energy(A) Increases(B) IncreasesIncreasesStays the sameIncreases(C) Stays the same(D) Stays the sameStays the same

In this question we have to answer whether Rotational Kinetic Energy and Translational Kinetic…

13. After the cylinder leaves the table, but before it lands, how do the rotational kinetic energy and transłational kinetic energy of the cylinder change, if at all? Rotational Translational Kinetic Energy Kinetic Energy (A) Increases (B) Increases (C) Stays the same (D) Stays the same Increases Stays the same Increases Stays the same

13. After the cylinder leaves the table, but before it lands, how do the rotational kinetic energy and transłational kinetic energy of the cylinder change, if at all? Rotational Translational Kinetic Energy Kinetic Energy (A) Increases (B) Increases (C) Stays the same (D) Stays the same Increases Stays the same Increases Stays the same

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter11: Angular Momentum

Section: Chapter Questions

Problem 27P: A solid cylinder of radius 10.0 cm rolls down an incline with slipping. The angle of the incline is...

See similar textbooks

Similar questions

A solid cylinder rolls up an incline at an angle of 20 . If it starts at the bottom with a speed of 10 m/s how far up the incline does it travel?
A hollow cylinder that is rolling without slipping is given a velocity of 5.0 m/s and rolls up an incline to a vertical height of 1.0 m. If a hollow sphere of the same mass and radius is given the same initial velocity how high vertically does it roll up the incline?
A diver goes into a somersault during a dive by tucking her limbs. If her rotational kindetic energy is 100 J and her moment of inertia in the tuck is 9.0kgm2 , what is her rotational rate during the somersault?
Repeat Example 10.15 in which the stick is free to have translational motion as well as rotational motion.
A 40.0-kg solid sphere is rolling across a horizontal surface with a speed of 6.0 m/s. How much work is required to stop it? Compare results with the preceding problem.
While exercising in a fitness center, a man lies face down on a bench and lifts a weight with one lower leg by contacting the muscles in the back of the upper leg. (a) Find the angular acceleration produced given the mass lifted is 10.0 kg at a distance of 28.0 cm from the knee joint, the moment of inertia of the lower leg is 0.900kg-m2 the muscle force is 1500 N, and its effective perpendicular lever arm is 3.00 cm. (b) How much work is done if the leg rotates through an angle of 20.0° with a constant force exerted by the muscle?
Three objects of uniform densitya solid sphere, a solid cylinder, and a hollow cylinderare placed at the top of an incline (Fig. CQ10.9). They are all released from rest at the same elevation and roll without slipping. (a) Which object reaches the bottom first? (b) Which reaches it last? Note: The result is independent of the masses and the radii of the objects. (Try this activity at home!) Figure CQ10.9
A solid cylinder of radius 10.0 cm rolls down an incline with slipping. The angle of the incline is 30 . The coefficient of kinetic friction on the surface is 0.400. What is the angular acceleration of the solid cylinder? What is the linear acceleration?
A tennis ball is a hollow sphere with a thin wall. It is set rolling without slipping at 4.03 m/s on a horizontal section of a track as shown in Figure P10.62. It rolls around the inside of a vertical circular loop of radius r = 45.0 cm. As the ball nears the bottom of the loop, the shape of the track deviates from a perfect circle so that the ball leaves the track at a point h = 20.0 cm below the horizontal section. (a) Find the balls speed at the top of the loop. (b) Demonstrate that the ball will not fall from the track at the top of the loop. (c) Find the balls speed as it leaves the track at the bottom. What If? (d) Suppose that static friction between ball and track were negligible so that the ball slid instead of rolling. Would its speed then be higher, lower, or the same at the top of the loop? (e) Explain your answer to part (d). Figure P10.62
What three factors affect the torque created by a force relative to a specific pivot point?
A turntable (disk) of radius r = 26.0 cm and rotational inertia0.400 kg m2 rotates with an angular speed of 3.00 rad/s arounda frictionless, vertical axle. A wad of clay of mass m =0.250 kg drops onto and sticks to the edge of the turntable.What is the new angular speed of the turntable?
A gyroscope slows from an initial rate of 32.0 rad/s at a rate of 0.700rad/s2 . How long does it take to come to rest?