I 20 132Q.25: For the linear transfomer circuit1:512,00y+shown:1002V,1. Find the value of V,, V2, h & 2?2. Calculate the total input power.(Ans.: V,=102-36.87°V. V2-504143.13°V, 4=2A. I,=0.4Z180°A & Pin=24W):-1752ideal

Answered: Image /qna-images/answer/7bc884eb-f4d6-4406-90b1-3f6364566d50.jpg

1312 Q.25: For the linear transfomer circuit 1:5 shown: 12,00y 1. Find the value of V,, V2, 4 & ? 2. Calculate the total input power. (Ans.: V, =102-36.87°v, V2-50Z143.13°V, 4=2A, 2=0.42180°A & Pin=24W) =175C2 ideal

1312 Q.25: For the linear transfomer circuit 1:5 shown: 12,00y 1. Find the value of V,, V2, 4 & ? 2. Calculate the total input power. (Ans.: V, =102-36.87°v, V2-50Z143.13°V, 4=2A, 2=0.42180°A & Pin=24W) =175C2 ideal

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

What are the unity-gain frequency and slew rate of the bipolar amplifier as shown if I1 = 100 μA, I2 = 400 μA, and CC = 10 pF? (b) If I1 = 300 μA, I2 = 350 μA, and CC = 10 pF?
(a) What are the Q-points of the transistors in the amplifier as shown if I1 =500 μA, R1 =1MΩ, I2 = 500 μA, R2 = 1 MΩ, and VCC = VEE = 7.5 V. Use βo = 80, VA = 75 V, Kp = 5 mA/V2, and VT P = −1 V. (b) What are the differentialmode voltage gain and input resistance and output resistance of the amplifier? (See Sec. 15.2.3.)
For the given amplifier circuit, asnwer the following question: a) For R1= 12 kΩ, R2= 10 kΩ, RE= 1 kΩ, RC = 1.2 kΩ, determine the following dc parameters: VB, VE, IE, and VC . (assume stiff voltage divider) b) For r’e = 5.5 Ω, R1= 12 kΩ, R2= 10 kΩ, RE= 1 kΩ, RC = 1.2 kΩ, RL = 7.5 kΩ, RS = 500 Ω, determine the input resistance at the base ( Rin(base) ), the total input resistance ( Rin(tot) ), voltage gain (Av) ,and attenaution. c) Assume that the overall voltage gain A’v = 120, the dc collector voltage VC = 6.3 V, and Vin = 15 mV rms. Determine the ac collector voltage (Vc) , then draw the total collector voltage waveform d) For r’e = 5.5 Ω, RE= 1 kΩ, RC = 1.2 kΩ, RL = 7.5 kΩ, determine the voltage gain if C2 is removed. Explain the effect of removing C2 on gain stability.
Since Vcc = 12 V, Vin = 690 mV, RB = 780 kΩ, RC1 = 27.9 Ω, RC2 = 25.4 Ω, RE = 470 Ω, RL = 47 Ω and β1 = β2 = 100 in the circuit in the figure Find the current (IL) flowing through RL? NOTE-1: VBE1 = VBE2 = 0.7 V will be taken. NOTE-2: Output impedances of transistors (r0) will be neglected.
Use BJT transistor to design an amplifier circuit that operates in the frequency range 10kHz-100kHz. Verify your design by simulating the design using the circuitmaker or multisim software. Use the standard resistor values (10% tolerance). The design should meet the following criteria: 1. Good stabilization of the Q-point 2. VCEQ is around ½ VCC. 3. High voltage and Current gain. From your design and simulation results, determine the following: a. β of the transistor b. VCEQ c. The voltage gain (AV) Please provide us with your simulation file and a report about your results
A common emitter amplifier as shown in Figure Q2 has the following parameters, β = 100, R1= 33K, R2 = 10K, RC = 3K3, RE = 1K, ro =  and VBE = 0.7 V.State all assumptions made.i. Check whether βRE>>10R2 is satisfiedii. Use the appropriate approach of analysis to determine the Quiescent point; IBQ,ICQ and VCEQ.iii. Draw the small signal equivalent circuit. Determine input impedance, Zin, outputimpedance, Zout, and the voltage gain, AV, if RL=20kΩ.
Differential amplifier circuit with resistive load topology and the current source, ISS is 0.2mA. Assume the circuit is symmetrical in which (W/L)1 = (W/L)2 =25/0.5 and μnCox = 50 μA/V2. i)Please evaluate the transconductance, gm and differential small-signal voltage gain, Av. Then, if the aspect ratio (W/L)2 = 2(W/L)1, investigate the effect on the transconductance of transistors M1 and M2. ii)Prove that gm2 = 2gm1.
Electronic Consider the circuit shown in figure, where be=710 mV, B = 100, and VA = ∞. Assume that the emitter current is equal to collector current. Sekildeki devre için BE=710 mV, B = 100 ve VA = ∞ oldugunu dikkate aliniz. Emiter akiminin kollektör akimina esit oldugunu kabul ediniz. Circuit parameters / Devre Parametreleri Rg = 30 kM, Rc = 400 R, RE = 400 R, Vcc = 4 V -> Alttaki devre için Q, transistörunün kollektor akimini Ic belirleyiniz. (Determine the collector current Ic of Q, for the circuit shown below.) (dogru katsayisi: 0.5) -> Alttaki devre için Q, transistörunün kollektör gerilimini Vc belirleyiniz. (Determine the collector voltage Vc of Q, for the circuit shown below.) (dogru katsays:: 0.5)
The input resistance of the amplifier used in the oscillator circuit shown in the picture is very large. No-load voltage gain is given as K0 = 5. For L = 0.1mH; Calculate the value of C1 and C2 capacitors for the circuit to oscillate at f0 = 2MHZ.
A) Design a buck-boost converter with the specifications: Vin = 28 V, in the range [24V,32V], Vout=12 V (with opposite polarity to Vin), load power in the range [0, 120 W], such that to operate in CCM for any line and load value. Select a switching frequency of 100kHz. Choose C= 1.8mF, 25V, 2.5mΩ
Since Vcc = 12 V, Vin = 690 mV, RB = 780 kΩ, RC1 = 27.9 Ω, RC2 = 25.4 Ω, RE = 470 Ω, RL = 47 Ω and β1 = β2 = 100 in the circuit in the figure Find the current (IL) flowing through RL? NOTE-1: VBE1 = VBE2 = 0.7 V will be taken. NOTE-2: Output impedances of transistors (r0) will be neglected. a. 16,56 mA b. 23,46 mA c. 8,28 mA d. 17,94 mA e. 20,70 mA f. 13,80 mA g. 26,22 mA h. 11,04 mA
For the circuit shown in Fig. 1 below, the transistor parameters are B =150, VBE =0.7V and VT=26mV. a) Determine the operating point parameters. b) Draw the small signal equivalent circuit based on the re mode c) Determine: i Gain of the transistor, Av Input impedance, Za i. Gain with signal, An V. Output voltage, given that V, =30mVSinot