14"#3 stirrup25"4- #11 4. Analyze the beam shown below given fe' = 3500 psi and fy= 60,000 psi:(a) Use d = 22 in. (effective depth of tension reinforcement), assuming the compression steelyields at the ultimate stage, calculate the reinforcing ratio of flexural reinforcement.(b) Is the beam underreinforced or overreinforced? Show reasons to your answer.(c) Calculate the nominal flexural strength of the section: M,?(d) Determine the design capacity of the section: øMn.

Solution Given Data f'c=3500 psify=60000 psid=22 in

Answered: 14" #3 stirrup 25" 4- #11

Engineering

Civil Engineering

14" #3 stirrup 25" 4- #11

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A prismatic beam having 275 mm x 500 mm is reinforced for flexure at the bottom with 5-ϕ16 mm with an effective depth of 420 mm. It is simply supported over a span of 6 m and designed to support uniformly distributed load over the entire span. Concrete weighs 24 kN/m3, Concrete strength f’c = 21 MPa and rebar strength fy = 280 MPa. 1. Determine the resulting depth of the uniform rectangular stress block in mm when the beam section reaches utlimate stage. 2. Determine the nomina moment strength in kN/m of the beam section as per NSCP 2015. 3. Determine the factored uniform load in kN/m the beam can sustain in addition to its factored self weight.
A reinforced concrete T-beam has the following properties: Flange width, bf = 1,350 mm Width of web, bw = 300 mm Gross depth, h = 500 mm Effective depth, d = 420 mm Concrete strength, f’c = 21 MPa Steel strength, fy = 415 MPa 10. If the beam is reinforced with 3-20-mm-diameter bars at the bottom (in single layer), determine the resulting depth of rectangular stress block at ultimate stage. = mm (2 decimal places) 11. What is the condition of failure? = (Balanced, Tension controlled, Compression controlled, Transition) 12. Calculate the design moment strength of a typical interior beam. = kN⋅m (whole number)
A prismatic beam having 250 mm x 500 mm is reinforced for flexure at the bottom with 4-ϕ16 mm with an effective depth of 420 mm. It is simply supported over a span of 6 m and designed to support uniformly distributed load over the entire span. Concrete weighs 24 kN/m3, Concrete strength f’c = 24 MPa and rebar strength fy = 280 MPa. Determine the resulting depth of the uniform rectangular stress block in mm when the beam section reaches utlimate stage. (A to D) Determine the nomina moment strength in kN/m of the beam section as per NSCP 2015. (E to H) Determine the factored uniform load in kN/m the beam can sustain in addition to its factored self weight. (I to L) A. 44.15 B. 78.85 C. 57.34 D. 98.56 E. 195.66 F. 89.60 G. 133.91 H. 110.15 I. 16.31 J. 39.16 K. 26.16 L. 20.51
Topic: Singly Reinforced Concrete A simply supported concrete beam 6m long is reinforced with four-28mm diam. tension barss. The beam has a width of 300mm and overall depth of 400m. The steel covering to the centroid of the reinforcements is 70mm, fc’= 30 MPa and fy= 418 MPa. A. Draw the stress diagram. B. Compute for the Ultimate capacity of the beam Note: Don’t conclude compression bars.
A doubly reinforced concrete beam has a max. effective depth of 630mm and is subjected to a factored moment of 1062 kn-m (including its own weight). fºc=27.58 MPa, fy = 413.4 MPa. Use 62.5 mm steel covering. 1. Determine the width of the beam. 2. Determine the reinforcement for compression. 3. Determine the reinforcement for tension.
A rectangular beam has a width of 330 mm and an effective depth to the centroid of the tension reinforcement of 432.5 mm. The tension reinforcement furnished is 7- 28 mm dia. bars and that for compression reinforcement is 4- 22 mm dia. bars placed 62.5 mm from the compression face of the beam. fy = 410.3 MPa and f'c = 35.9 MPa. Answer the following: (1) Determine the depth of the compression block. (2) Determine the design strength using 0.90 as the reduction factor. (3) Determine the concentrated live loads at the midspan in addition to the dead load of 19.7kN/m including the weight of the beam if it has a span of 9 m.
The concrete post shown is reinforced axially with four symmetrically placed steel bars each of cross-sectional are 900mm^2. If the 1000 kN axial load is applied and the moduli of elasticity are 200 GPa for steel and 14 GPa for concrete. Determine a) the stress in each of the steel bars, and b) the stress in the concrete.
The continuous beam and post system shown below supports a 10 kip vertical load and a5 kip horizontal load. Determine the combined normal stress at point “A” and point “B”.State if the points are in tension or compression.
Determine the prestressing force required for the precast concrete T-beam. Use the following data: Total moment = 250 kN-m Effective stress fse= 862 MPa Allowable concrete stress = f =11 MPa Consider zero stress at the bottom of the beam I=3673x106 mm A=103125 mm2 Eccentricity = 271.6 mm Centroid of steel is located at 100 mm from the bottom of the beam.
A rectangular reinforced concrete beam exposed to earth has a total depth of 600 mm and a width o 350 mm. It is reinforced with 3- 22 mm diameter bar (fy' = 315 MPa) in compression and 5 - 25 mm diameter bar in tension (fy= 345 MPa). fc' = 28 MPa a. determine the effective depth of the beam b. determine the depth of compression block c. check if steel yields for both tension and compression reinforcement d. determine the ultimate capacity of the beam
A rectangular reinforced concrete beam with width of 350 mm and effective depth of 600 mm is subjected to 250 Kn.m bending moment. the beam is reinforced with 6-25 mm bars. Use alternate design method and modular ratio, n = 10. a. find the location of the neutral axis from the bottom of the beam & moment of Inertia. b. Find the maximum stress of concrete and steel c. total compression force in concrete?
Calculate the required amount of reinforcement (in in2) considering the ultimate moment below. Use english units. Note: Use the following equations for minimum reinforcement in English units. Pmin for flexure = (3*sqrt (f'c))/fy greater than or equal to 200/fy f'c = 3000 psi fy = 40 ksi Mult = 200 ft-k