14.) Find the value of power dissipated if a voltage v = 240 sin (30t + Tt/4) is applied to a resistor of 32 ohms.

Q: se the superposition theorem, find the current in t40 resi:stor of the circuit shown. 202 10V SO V…

A:

Q: 25. Each RC circuit in an op-amp (a) causes the gain to roll off at -6 dB/octave (b) causes the gain…

A: 25. Answer: answers (a) and (b)   Explanation: a) It is also a valid option. The RC network is a…

Q: mine the number of bits per level required when using FSK with 4 alffere frequencies and QAM with a…

A: It is given that: FSK with 4 different frequencies QAM with a constellation of 256 points

Q: 1 a) Calculate resonant frequency, & where f. and @. VLC b) half-power frequencies fi and f2 where R…

A: The given circuit is a series RLC resonance circuit and the resonance will happen if the impedance…

Q: Difference between technical ang operational definitions

A: Technical definition means a list of description that how the device is designed to work and what…

Q: A sinusoidal signal passes a continuous time LTI system, the output is O another sinusoidal signal…

A: The solution is given below

Q: Solve for the inverse Laplace transform of the following functions 6(s+3) (s+1)(s+2)(s+4) s3+2s+6 a.…

A:

Q: (a) Household appliances need to be individually fused to keep them safe in case of fluctuations.…

A: A list of household appliances are given in the question. We need to determine the rating of fuses…

Q: 2) The amplitude of the emf in the below circuit is 150V, while the angular frequency is 60x. The…

A: As per the guidelines of Bartley we supposed to answer first three subpart only for solution of…

Q: S t A or B: (A) The voltage across a 5-mF capaciter is shown. Determine the current through the…

A:

Q: Power [dB] 10. Compute the Root Mean Square(RMS) delay of the following channel's power delay…

A: Formula to calculate RMS value is given below: =P12+P22+ ----+Pn2

Q: The -------parameters may not reflect the actual operating conditions but simply provide an…

A: 1. The advantages of the re model are that the variables are determined by the real operating…

Q: c) The waveform shown in Figure 1c is passed into an Ideal Low Pass Filter (ILPF) which has a…

A: Given the signal as shown below: The waveform shown in Figure 1c is passed into an Ideal Low Pass…

Q: Find the current and voltage using superposition across the 4- k2 resistor(I, and Vx, respectively).…

A:

Q: ded system is determined by the _________ of the gains of each stage. a.product b.difference c.sum…

A:

Q: The drawback to using this equivalent circuit, however, is that it is defined for a set of operating…

A: Answer: hybrid   Explanation: a) It is not a valid option. It is not a type of AC model b). It is…

Q: For tha cirenits ahown, calenlab rhe currout hrongh the 9 A resiator as ing za emperposition…

A:

Q: b) Calculate the cut-off frequency and overall gain for the circuit in Figure Q2(b). (ii) Justify…

A:

Q: In an amplifier circuit, the magnitude of the output current is always greater than the input…

A: The function of the amplifier is increases the magnitude of input signal or power. So the output…

Q: Q2- For tha cirenits ahown, calenlat re eurront hrongh the 9 A reaiator ugs ing zu Enperposition…

A: In this question we need to find a current through 9 ohm resistor by using superposition theorem.

Q: [3] Complete the following timing diagram for the D type flip-flop covered in class (the flip-flop…

A: D flip-flop: The D flip-flop is a single-digital-input timed flip-flop. The output of a D flip-flop…

Q: The maximum and minimum stresses in the dielectric of a single core cable are 40 KV/cm (rms) and 10…

A: Given, Maximum stress in dielectric, gmax=40 kVcm (rms) Minimum stress in dielectric, gmin=10 kVcm…

Q: A 11 (mA mA 12 60 V V R1 3002 R2 6002 V1 V2 Fig. 5-4 Measured Values Calculated Values Rem V1 = V1 =…

A:

Q: Hiw/Consider the glam shown below. dblae the closed Loop hanser function CO/RS)

A:

Q: Design a frequency divider circuit from JK flip-flops which generates a 12.5MHz signal from the…

A: Frequency Division : A frequency divider can be used to construct from j-k flip flops with the help…

Q: (a) Summarize the differences between passive filter and active filter in terms of gain, cost and…

A:

Q: Astable multivibrator was designed using a 555 timer. The periodic time of the output signal should…

A: We need to find out the value of resistance for given timer

Q: Operational Amplifiers] Determine I and Vout

A: In this question,   We need to determine the voltage Vo and current I as shown the circuit.  We are…

Q: 3. Calculate the inductance of the line of the circuit as shown. The radius of conductor x is 20mm…

A: In this question we need to find a inductance of line

Q: b) i) Arrange AM, SSB-SC, DSB-SC, and FM in the decreasing order of bandwidth required for…

A: Since you have asked multiple questions, we will solve one question for you. If you want any…

Q: V1 V IT R1 mA 3002 V2 = 80V V R3 6002 VA V

A:

Q: Vo (w) H.W.1: For the circuit shown, obtain the transfer function Identify the type of V, (m) filter…

A:

Q: H.W. : Design a low-pass RC filter to have a cutoff frequency of 30 krad/s. Use a 0.01- uF…

A:

Q: Find the Fourier Transform of the triangular pulse -t for – 1 <t < 0 | x(t) = (1+t for 0 <t <1

A: In this question,   We need to determine the Fourier transform of the given signals.

Q: (TCO 1) If the gain in decibels of an amplifier is 76.9, what is the straight gain? 6998 6578 6745…

A: Given, Gain of an amplifier in decibel is 76.9

Q: (a) The following circuits made of universal gates could be replaced with just one single gate for…

A:

Q: Which of the following characteristics indicates a practical amplifier design in terms of input…

A:

Q: Q3 Referring to the circuit in Figure Q3, determine the values of current, i, and iz by using nodal…

A: We need to find current for given circuit

Q: 6. Whether the value of synchronous impedance (Zs) is constant? State the conditions on which it…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: In a Common Emitter (CE) Fixed Bias (FB) configuration, the output impedance is almost equal to…

A: DC conditions are represented via transistor biassing. Transistor biassing is defined as the proper…

Q: a) I) Sketch (with full labelling) an example of each of a random, energy, power signals. i) Sketch…

A: Random Signals: The lack of predictability characterizes a random or stochastic signal. In contrast…

Q: An analog signal ¤a(t) = sin(480at) – 3 sin(720at) is sampled at 600 times per second. What is the…

A: NOTE- As per the policy we can solve one question, please post other question as separate question .…

Q: V1 V IT R1 mA 3000 V2 R3 110 V V3 V 6000 V R2 2002 Fig. 5-8 Measured Values Calculated Values…

A: This problem can be solved by using ohm's law

Q: In Geiger -Muller counter, no amplifications is needed when operated in the avalanche mode. O true O…

A: Since one avalanche mode in Geiger-Muler counter results in  consecutive avalanche which makes ion l…

Q: Problem 3 A 3-phase 2-pole induction motor is rated 190 V, 60 Hz, it is connected in Y, and has R2 =…

A:

Q: 2) The amplitude of the emf in the below circuit is 150V, while the angular frequency is 60x The…

A:

Q: (c) (i) Design a first-order high pass Butterworth filter with a cut-off frequency of 5 kHz and pass…

A:

Q: For the circuit as shown in figure below, find the value of Vx such that the 5A current source…

A:

Q: Simplify the following complex numbers. (Write your answers in rectangular form a. i257 + i388 + i4…

A: The solution is given below

Q: A circuit consisting of a resistor in series with an inductance

A:

Electrical Heating Unit

The conversion of electrical energy to heat energy is known as electric heating. The heating system that converts the electrical energy to heat energy for various application is called electrical heating unit. Electricity is employed as the firing mechanism in electric heating systems, which transforms electric current to heat. Electric heaters have heating elements in the form of electric resistors.