need help - discrete time signal An analog signal x. (t) = sin(480nt) – 3 sin(720nt) is sampled at 600 times per second. What is the expression for the resulting discrete time signala[n]?O a.-2 sin()O b. -4 sin()O c. 2 sin()O d. sin()Oe.- sin()O f. 4 sin()The analog signal aa (t)j(120at-) + e–j(180xt-) is sampled at F, = 300 Hz. What is the expression for the resulting discrete time signal a n?O a. 2 sin(2)O b. -0.5 sin()sin()O d. -2 sin()Oc.- sin()O f. 0.5 sin()Oe.

NOTE- As per the policy we can solve one question, please post other question as separate question .…

An analog signal ¤a(t) = sin(480at) – 3 sin(720at) is sampled at 600 times per second. What is the expression for the resulting discrete time signal ¤[n]? -2 sin( ) O b. -4 sin( ) O c. 2 sin() O d. sin() O . - sin() O f. 4 sin()

An analog signal ¤a(t) = sin(480at) – 3 sin(720at) is sampled at 600 times per second. What is the expression for the resulting discrete time signal ¤[n]? -2 sin( ) O b. -4 sin( ) O c. 2 sin() O d. sin() O . - sin() O f. 4 sin()

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Signals and Systems An analog signal is given as x(t) = 5 + 2 cos(20??) + 3 cos(400??)a) What is the bandwidth of x(t)? Determine the Nyquist sampling frequency for x(t), both in radian/sec (ws), and in Hz (Fs ).b) Formulate ?? (??), the signal sampled with the Nyquist frequency.c) Plot frequency spectrum of the sampled signal, Xp(jw).d) Determine the filter to reconstruct the signal x(t).e) Is it possible to reconstruct the signal x(t) for Ts = 0.004 [s]? State that if aliasing error occurs ornot
A subcarrier given in Eq. 4.1 is amplitude modulated by an information signal given in Eq. 4.2. The resulting AM signal is then used to amplitude modulate the signal given in Eq. 4.3 to generate a signal that is finally transmitted. Derive a mathematical expression for this final signal that is transmitted. How, in practice, can this system be made with minimum harmonic distortion? Equations for Question 04
A digital communication link carries binary-coded words representing samples of an input signal, xa(t)=3cos⁡(600πt)+2cos⁡(1800πt)The link is operated at 1,000 samples/s. (a) What is the folding frequency? (b) What is the Nyquist rate for the signal xa(t)? (c) What are the frequencies in the resulting discrete-time signal x(n)? (d) Will there be any aliasing here? (e) Which frequency will alias to what frequency
Obtaining broadband FM signal from narrowband frequency modulated (FM) signal is shown below. The narrowband FM signal has a maximum frequency deviation of 100 Hz. The frequency of the local oscillator is f0=100 kHz. Since the sign at point A is Ac(cos 2πf0t+θ(t)), express the signs at points B and C. Ac is a constant and θ(t) is a function of m(t).
A continuous time signal, x(t) = sin(20πt) + cos(40πt), is sampled uniformly at intervals of T to obtaina discrete time signal,x(n) = sin(πn/5) + cos(2πn/5).a) What is the value of T assuming no aliasing has occurred?b) Assume both frequency components have been aliased. In this case, is your choice of T unique? If not,specify some choices of T consistent with the information given
During a vibration measurement experiment in the Mechanical Engineering Department at Hacettepe University, a piezoelectric accelerometer output is given by this mathemtaical equation: a (t) = 1 + 4 sin(43.98t) + 7sin(100.53t) in gravity acceleration (g) value. a) Determine the frequencies (in Hz) contained in the signal. Round your results to nearest integer value. b) What is the minimum sampling rate to avoid aliasing? c) Sketch clearly the frequency spectrum if the signal is sampled at 15 Hz. d) Now, the signal is filtered with a low-pass Butterworth filter to remove the maximum frequency component. It is desired to attenuate the amplitude of this component to at least 5 % of its value. If the sampling rate is now 20 Hz, what will be the order of the filter? e) If the blue one is our signal, then what is red and green ones? Write down the mathematical relation between the three signals? (Use labels as blue, red and green signal.)
a) Calculate the range of values K will take for the steady-state error to be “??? ≤ 0.04” when the input of the system is ?(?) = ?. b) Calculate the value range that K will take so that the damping ratio can be “1 > ξ ≥ 1 2√6”. c) Calculate the damping ratio “ξ” and the undamped natural frequency ?? value so that “? = 0.5”.
Kindly help to answer this figure shown. Find the transfer function of the system whose signal flow graph is shown
An FM signal, eFM = 50 sin [2π(800k)t - 4 sin 2π(5k)t] is produced by a frequency modulator with -500Hz/V frequency deviation constant. Determine (a)Determine the equation of the carrier signal (b) What is the equation of the modulating signal (c) Determine the approximate bandwidth of the FM signal (use Carson’s Approximation)
4. A single sideband signal is derived from a sinusoidal carrier of 100kHz and audiofrequencies between 6kHz and 10kHz. In this situation, the upper sideband wouldextend from:a 106kHz to 110kHzb 210kHz to 216kHzc 90kHz to 94kHzd 6kHz to 10kHz 5. A BFO:a extracts the lower sideband from a DSB transmission.b generates a signal that is exactly twice the frequency of the system carrier wave.c generates a sinewave of constant frequency.d allows FM signals to be demodulated on an AM broadcast receiver
A robotic system with transfer function ?(?) =(100)/(s(0.1s+1)(0.1s +1)) is controlled with gain K as shown in the figure. A)To analyze the frequency response of this system, draw the Nyquist graph. B)Apply the Nyquist stability criterion. C)Verify the stability analysis you made in part (b) by plotting root locus plots for the positive and negative values of the K gain. D)Calculate the gain value that makes this system borderline stable and show it on Nyquist and Root locus graphs. E)Calculate the gain margin, phase margin, gain crossover frequency and phase crossover frequency values. F)Explain whether the system is stable over the gain margin and phase margin values. WE NEED TO SOLVE THE PROBLEM IMMEDIATELY. PLEASE HELP.
Obtain the observable canonical state space form of the system whose pulse transfer function is given below.please pay