140 mm 140 mm A centric load P is applied to the granite block shown. Knowing that the resulting maximum value of the shearing stress in the block is 17 MPa, determine the the normal stress (MPa) exerted on that surface where shear is maximum, (2 decimals). Note: If compression add minus sign. 11:05 am

140 mm 140 mm A centric load P is applied to the granite block shown. Knowing that the resulting maximum value of the shearing stress in the block is 17 MPa, determine the the normal stress (MPa) exerted on that surface where shear is maximum, (2 decimals). Note: If compression add minus sign. 11:05 am

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Calculate the corresponding depth of uniform stress block in a reinforced concrete beam 40*10 deep reinforced with the bars 20mm in diameter enclosed with 10mm diameter stirrups when the tensile steel strain is 0.008 and concrete strain is 0.003. f'c = 22MPa.
An open top standpipe as shown has a radius r= 2.2m and 20 mm wall thickness. Determine the height ? (?? ??????)of the water that will result to a circumferential stress of 24MPa in the wall of the standpipe. NOTE: The specific weightof water is 9.81???3. Remember, pressure is equals to the product of specific weight and height. Use 2 decimal places.
f’c = 28 fy = 415 Mpa ex= 320mm a. Calculate depth of neutral axis b. Calculate the stress in extreme compression reinforcement in Mpa
A hollow, circular, steel column (E = 30,000 ksi) is subjected to a compressive load P. The column has length L = 8.0 ft and outside diameter d = 7.5 in. The load P = 85 k. If the allowable compressive stress is 7000 psi and the allowable shortening of the column is 0.02 in., what is the minimum required wall thickness t min?
A 4.75-in. outside diameter polyethylenepipe designed to carry chemical waste is placedin a trench and bent around a quarter-circular 908bend (see figure). The bent section of the pipe is52 ft long.(a) Determine the maximum compressive strainεmax in the pipe.(b) If the normal strain cannot exceed 6.1x10 -3 ,what is the maximum diameter of the pipe?(c) If d = 4.75 in., what is the minimum acceptablelength of the bent section of the pipe?
Define while applying the direct shear test on sand grains and for glass rods, will the angle of internal friction be of same range?
Provide correct answer Thanks for the help Determine maximum principal stress
A piece of engineering equipment is supported by thefoundation shown. The diameter of the circular pin is 20 mm. a.) Determine the value of P so as not to exceed the allowable bearing stress of 310.5 Mpa in the circular pin.b.) Determine the value of P so as not to exceed the allowable shearing stress of 138 Mpa in the circular pin.
A piece of engineering equipment is supported by thefoundation shown. The diameter of the circular pinis 20 mm. a.) Determine the value of P so as not toexceed the allowable bearing stress of310.5 Mpa in the circular pin.b.) Determine the value of P so as not toexceed the allowable shearing stress of 138Mpa in the circular pin.
d. Secant modulus at a stress of 62 ksi.e. Tangent modulus at a stress of 65 ksi.
Discuss aboout Self-straining loads
29 A square footing 2.2 m x 0.39 m thick supports a 300 mm square column at its center. Column loads are service conditions: DL = 317 kN LL = 217 kN f’c = 21 MPa fy = 415 MPa Concrete cover to the centroid of steel reinforcement = 100 mm Calculate the nominal one way shear stress in the slab. Write your final answer with 2 decimal places if the unit is MPA.