Problem (7.1): An element in plane stress from the frame of a racing car is oriented known angle 6 (see Figure 7.30). On this inclined element, the normal and shear have the magnitudes and directions shown in the figure. Determine the normal and she stresses acting on an element whose sides are parallel to the xy axes; that is, determine Oy, and Txy. Show the results on a sketch of an element oriented at 0 =0°. at stresses 4,180 psi 2,360 psi 0=30° 15,220 psi Figure (7.30)

Problem (7.1): An element in plane stress from the frame of a racing car is oriented known angle 6 (see Figure 7.30). On this inclined element, the normal and shear have the magnitudes and directions shown in the figure. Determine the normal and she stresses acting on an element whose sides are parallel to the xy axes; that is, determine Oy, and Txy. Show the results on a sketch of an element oriented at 0 =0°. at stresses 4,180 psi 2,360 psi 0=30° 15,220 psi Figure (7.30)

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter8: Vertical Stress Increase In Soil

Section: Chapter Questions

Problem 8.6P: Two line loads q1 and q2 of infinite lengths are acting on top of an elastic medium, as shown in...

See similar textbooks

Similar questions

In the figure, forces with resultant intensity Fx = 3P (unit N), Fy = 2P (unit N) and Fz = P (unit N) act on the side faces of the cube whose dimension a = 20 mm. The limit stress for the uniaxial stress case in the material is 40 / Mpa safety coefficient n = 2. How many Newtons (N) is the largest P value according to the Von Mises assumption for the cube to be safe? please please fast help me
Determine the stress components (σx′ , τx′y′) acting on the inclined plane AB in (Figure 1), where τxy=−38.5MPa. Solve the problem using the method of equilibrium.
Q#2 Draw the Mohr,s circle for the stress element shown in figure. Determine the principal stresses and maximum in-plane shear stresses and also draw respective stress elements. Furthermore find out stresses on planes whose normal make an angle of 45 and 135 degress with x-axis. Show your results on stress elements (10 marks)
Mechanics of Materials (Statically Indeterminate Members) A homogeneous bar with a cross-sectional area of 400 mm2 is attached to fixed supports as shown in the figure. It is subjected to lateral forces P1 = 20 kN and P2 = 50 kN. Determine the normal stress developed in segments AB and BC.
The frame given in the figure below has three degrees of freedom in C (1,2,3) and three degrees of freedom in B (4,5,6) .In Figure 1:Open the vertical deformation at node C and apply force F and close the other degrees of freedom.Now , If we separate the CD column and the BC beamAccording to the stiffness method What is the status of the forces and moment on the CD in C? In other words, what is the ratio of forces R1 F R3 R4 R5 R6 Apply to CD column in C? And what is the position of the forces and anchors on BC in B and C? In other words, what is the ratio of forces R1 F R3 R4 R5 R6 Applied to BC beams in C and B? In Figure 2:Open the rotation at node C and insert the momentM and close the other degrees of freedom.Now , If we separate the CD column and the BC beamAccording to the stiffness method What is the status of the forces and moment on the CD in C? In other words, what is the ratio of forces R1 R2 M R4 R5 R6 Apply to CD column in C? And what is the position of the forces and…
In Figure 2, the system under the torsional effect;Draw the torsional moment diagram.Determine the torsional angle CA (rotation angle) that will occur at point C.Determine the maximum shear stress that will occur in the system.(G=80 000 MPa)M1(Nm) 9000 M2(Nm)2000 D1(mm) 90 D2(mm) 60 D3(mm) 50 D4(mm) 30
Figure shows a state of plane stress consists of normal stresses σx = 60 MPa and σy = -40MPa; and unknown shear stress, ?xy. The maximum principal stress was determined to be 104.34 MPa. Using Mohr’s circle, determine; the magnitude of the shear stress, the principal plane and the minimum principal stress. Then, sketch the element showing all stresses in its proper orientation, the maximum shear stress, associated normal stress and the orientation of the element. Then, sketch the element showing all stresses in its proper orientation, the stress components acting on the inclined plane AB. Then, sketch the element showing all stresses in its proper orientation.
The system shown in the figure consists of two bars and is subjected to a force at B and C.[d1 = 53 mm, d2 = 32 mm, L1 = 1.2 m, L2 = 1.3 m, E= 120 GPa, PC = 35 kN, PB = 35 kN] Determine the deformation of rod (2)? Determine the displacement of point C?in mm
3.2: Find the angle & in the case of stress shown in the figure. The answer: 71,57 degree
S1) The figure shows the stress distribution in the rectangular cross section of a beam.According to this;(a) Write the expression for stress ?x, taking into account the directions of Fx, My and Mz.(b) Show that My is zero for symmetrical normal stress distribution.(c) Using the stress function ?x, find the axial force Fx acting on the rectangular cross sectionin width b and height h.(d) Obtain the equation of Mz bending moment.Hint: In this question, using the stress distribution in the figure, it is aimed to determine thecross-sectional effects of Fx, My ve Mz causing this stress distribution
Determine the magnitude of the shear stress (in units of MPa) when the state of stress is oriented 45 degrees from the element shown (aligned with line AB).
Solve for the equivalent force on an inclined surface. Look at Figure A.1 below. You will see a triangular block cut from a stress block with known stresses. The size and thickness of the block does not matter, so we will assume the area of the sloped inclined surface is A (sorry that it is the same symbol as the Point). If the area of the sloped surface is A, then the area of the other two surfaces is A cos (Theta) and A sin (Theta). First, draw a FBD of the block by multiplying each stress (normal and shear, known and unknown) by their associated area (in terms of A). Second, break the stress vectors on the side and bottom into components along the x’ and y’ axes. Third, sum the forces in the y’ direction and set them equal to zero (you should now be able to cross out the value of A for each term in your equation resulting in an equation with only one unknown, the normal stress in the y’ direction). Solve for the value of the normal stress in the y’ direction. Now repeat for…