15-20|A one-way interior slab panel, continuous on both ends, is built integrally with the beam supports. It has an unsupported span if 3.2m. and carries a total factored uniformly distributed load (including self-weight) of 11.2 KPa. Use D12mm reinforcement, fc' = 28MPA and fy=350MPA %3D 15. Based on the NSCP code provisions for solid one-way slabs, what is the required minimum thickness for the given slab? a. 320.0 mm b. 160.0 mm c. 133.3 mm d. 114.3 mm e. None of the above 16. Using the NSCP approximate moments for one way slabs, what is the design positive moment at midspan? 11.46 kN-m b. a. 10.42 kN-m 8.19 KN-m 7.17 kN-m None of the above с. d. е. 17. Using the NSCP approximate moments for one way slabs, what is the design negative moment at the interior face of the interior support? 11.46 kN-m b. a. 10.42 kN-m 8.19 KN-m C. 7.17 KN-m None of the above d. е. 18. What is the minimum steel reinforcement ratio for the given slab with fy=350MPA? a. 0.0016 b. 0.0017 C. 0.0018 d. 0.0020 e. None of the above 19. What is the maximum allowable spacing of reinforcement for the given slab if hf = 125mm? a. 250 mm b. 375 mm C. 450 mm d. 453 mm е. None of the above

15-20|A one-way interior slab panel, continuous on both ends, is built integrally with the beam supports. It has an unsupported span if 3.2m. and carries a total factored uniformly distributed load (including self-weight) of 11.2 KPa. Use D12mm reinforcement, fc' = 28MPA and fy=350MPA %3D 15. Based on the NSCP code provisions for solid one-way slabs, what is the required minimum thickness for the given slab? a. 320.0 mm b. 160.0 mm c. 133.3 mm d. 114.3 mm e. None of the above 16. Using the NSCP approximate moments for one way slabs, what is the design positive moment at midspan? 11.46 kN-m b. a. 10.42 kN-m 8.19 KN-m 7.17 kN-m None of the above с. d. е. 17. Using the NSCP approximate moments for one way slabs, what is the design negative moment at the interior face of the interior support? 11.46 kN-m b. a. 10.42 kN-m 8.19 KN-m C. 7.17 KN-m None of the above d. е. 18. What is the minimum steel reinforcement ratio for the given slab with fy=350MPA? a. 0.0016 b. 0.0017 C. 0.0018 d. 0.0020 e. None of the above 19. What is the maximum allowable spacing of reinforcement for the given slab if hf = 125mm? a. 250 mm b. 375 mm C. 450 mm d. 453 mm е. None of the above

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Load = 3000 lb Q:Find Stresses at: Section A-B & Section D-C "18.0"- "5,5" Plain Concrete: D Compressive Strength : 280 (Psi) "12.0"- "0.5"-
The 5-story building design project will have its beams and slab poured monolithically and formed a T- section as shown. Determine the design strength oMn in accordance with the ACI/NSCP Code. The tension steel is 9- 36 mm diameter bars (As of 36 mm = 1006 mm2) with three bars in each of three layers. Assume 12 mm stirrups are used, and there is 25 mm between layers. Use fc' = 28 MPa and fy = 413.70 MPa. 750 mm T175 mm 1000 mm 9-36 mm dibmeter bars 350 mm dooo
Design a one-way slab with a simple span of 3.0m. The slab is to carry a uniform live load of 7.15 kPa. Assume f’c = 27.6 MPa and fy = 276 MPa for main and temperature bars. use: -12 mm dia RSB for main reinforcement -10 mm dia RSB for temperature and shrinkage reinforcement hello please answer this thanks ☺️
A rectangular beam has b = the concrete compression strength is yield strength fy = 415 MPa. reinforcement use NSCP 2010 N.A. As 350 mm and d= 460 mm. 30 MPa and the steel Calculate the required steel 70 mm. area if the steel cover is 350 Md= ML = 460 230 KN-m 160 KN-m 70 mm mm
Design the slab reinforcement if the maximum positive moment is Mup=wul2/11 . and the maximum negative moment is Mup=wul2/19. Include the design for S&T bar. Given: length = 6m span = 2m Wu= 8.572 kPa Slab thickness = 150 mm f'c = 28 MPa fy= 219 MPa main bar = 10 mm s&t bar = 8mm
3 نقاط The minimum reinforcement using mild steel in slab should not be less than .., if fy=420 MPa ...... 2.0% 1.8% 0.15% 0.18%
Double reinforced section-A', is known] The design moment for a RC beam is M=450kN-m, bXh=250mmX550mm. If the concrete of grade C35, the steel is of grade HRB400. there are 3 t 20 reinforcement embedded in the compression zone and A',-942mm2. Design the required reinforcement A,. Data: C35 concrete: f =16.7N/mm, f, = 1.57N / mm a, =1.0 HRB400: f, = 360N/ mm, 5,= 0.518 a 40mm %3! %3D Effective depth: h, 550-65= 485mm %3D
5. The beam shown is reinforced for positive moment with three epoxy-coated #11 bars. The bars terminate at the center of the supports. Neglecting beam weight (concentrated loads are very heavy), determine if the required development length is satisfied. Assume As required = 4.55in², 2 in. clear cover on all sides of the longitudinal reinforcement, normal weight concrete, #3 stirrups @12 in o.c., f'c = 5000 psi and fy = 60,000 psi. 8 ft | Pu 20 ft Pu 8 ft ge2 of 56 30 in b=14in. ed 5/15/2020 As = 3-#11
Please answer asap. Will rate immediately. Thank youuu A slab panel is carrying a superimposed dead load of 2.70 kPa and superimposed live load of 6.0 kPa all over the 4.0m x 18m light storage area. The slab is restrained. The concrete to be used has strength of 28MPa (normal weight). The main reinforcement has yield strength of 350MPa. Use concrete cover of 20mm. The thickness uses a multiple of 10mm. The main reinforcement used us 16mm in diameter. The shrinkage and temperature reinforcement used is 12mm in dia. The unit weight of concrete is 23.6 kN per cubic meter. Using USD, 1. Determine the spacing of 10mm temperature and shrinkage rebar. 2. Determine the ultimate pressure that the slab will carry 3. Determine the spacing of 12mm main rebar at the midspan 4. Determine the spacing of 12mm main rebar at the support.
A continuous solid slab system shown in Fig. (1) supported by beam with (bw=300 mm and h-650 mm) and the beams supported by columns (350 mm x 350mm). The slab system carries a uniform dead load (excluding self-weight) 5.6 kN/m² and live load 6.2 kN/m². Design the slab SI and S2, and calculate the load on beam B1. Draw all the reinforcement detailed sections. (Using f'c =30 mPa, fy= 420 mPa, bar dia. Ø 12). 4m 4.3 m 4.3m 4m Fig (1). 5 m 5m S1 81 B1 $2
Q2// A floor system consists ofconcrete slab supported by continuous beam h = 140mm , bw = 300mm,d = 550mm, f 28MPA, fy = with: %3D 420MPа. Determine the steel reinforcement required at mid span of interior beam to resist service dead load moment Ma = 320KN.m and service live load moment M = 250 kN.m %3! %3D 8m + 3m 4 3m 3m 1-1
A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f'c = 21 Pa and steel yield strength fy = 415 MPa for 20-mm bars and fy = 275 MPa for 16-mm bars Determine the limiting tensile steel ratio for a tension controlled condition in positive or negative bending with the given material strengths.